Question about 1997 Chevrolet K1500

Open Question

Picture of EGR Pintle Position Circuit on 1997 Chevrolet K1500

Where is the EGR Pintle Position Circuit

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

drsinister69
  • 2317 Answers

SOURCE: new egr valve code says closed pintle position.

You can remove the EGR and test with vacuum to see if it opens, it maybe carboned up. Also check the supply of vacuum to the EGR from the motor. The maybe a bad control vacuum solenoid, not allowing vacuum to open the EGR, when required.

Posted on Mar 15, 2010

ftw1952
  • 10319 Answers

SOURCE: 1997 CAVLIAR 2.2 LITER OB11 READS ( EGR FLOW

Either the EGR solenoid is at fault or the EGR valve is

Posted on Apr 21, 2010

redds55
  • 2620 Answers

SOURCE: 1996 chevy blazer check engine light code p1406

Replace EGR Valve

Posted on Oct 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable cause(s) of DTC P1406?


Definition of Diagnostic Trouble Code P1406 Audi: EGR Temperature Sensor Range/Performance BMW: Heated Catalyst Internal Control Module Checksum/ROM Error Buick: EGR Valve Pintle Position Circuit Cadillac: EGR Valve Pintle Position Circuit Chevrolet: EGR Valve Pintle Position Circuit Ford: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged GMC: EGR Valve Pintle Position Circuit Isuzu: EGR Valve Pintle Position Circuit Lincoln: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged Mazda: DPFE Sensor Downstream Hose Off Or Plugged Mercury: Differential Pressure Feedback Sensor Downstream Hose Off Or Plugged Oldsmobile: EGR Valve Pintle Position Circuit Pontiac: EGR Valve Pintle Position Circuit Saturn: EGR Valve Pintle Position Circuit Toyota: Turbo Pressure Sensor Range/Performance Problem Volkswagen: EGR Temperature Sensor Range/Performance Volvo: Termperature Warning > 100 degrees C

Jun 18, 2015 | Cars & Trucks

1 Answer

P1406 position circuit pintle


Yes an EGR will cause a vehicle to not start. That code means EGR is not working properly and That the pintle is stuck in the open or closed position. The EGR burns the unburned fuel that wasnt burned the first time by passing it through the engine again instead of raw fuel out the tailpipe.

Jan 01, 2014 | 1997 Chevrolet Astro

1 Answer

What would be the first and most likely reason for my 1997 buick lesabre to be giving me a egr pintle position circuit malfunction?


This code indicates a problem with the EGR valve's pintle position. The EGR Valve's pintle could just be stuck in which case the problem could be fixed by cleaning the EGR valve.

If the EGR valve is electronically controlled or cleaning the valve does not fix the problem, you will most likely have to replace the EGR Valve.

Keep in mind that the EGR valve relies on inputs from other sensors to determine the pintle position. If one of these other sensors is not operating correctly, it could be giving you a false P1406 error code.

Dec 19, 2012 | 1997 Buick LeSabre

1 Answer

Trouble code P1406 Failed EGR value, Open or short circuit condition Also code P0301 misfire cylinder 1 Next steps? Information for replacing EGR value? 1997 Bonneville SE 105K


P1406 Code - EGR Valve Pintle Position Circuit
The PCM monitors the EGR valve pintle position input to ensure that the valve responds properly to commands from the PCM and to detect a malfunction if the pintle position sensor and control circuits are open or shorted. If the PCM detects a pintle position signal voltage outside the normal range of the pintle position sensor, or a signal voltage that is not within a tolerance considered acceptable for proper EGR system operation, the PCM will set DTC P1406.

CONDITIONS FOR SETTING THE DTC

Ignition 1 voltage is greater than 10 volts.
EGR Feedback is less than 0.14 volt at any time.

OR

EGR Feedback is 0.4 volt greater or less than the EGR Closed Valve Pintle Position when the Desired EGR Position is commanded to 0%.

OR

Actual EGR Position is 20% greater or less than the Desired EGR Position.
Any of the above conditions are present for longer than 20 seconds.

ACTION TAKEN WHEN THE DTC SETS

The PCM will illuminate the Malfunction Indicator Lamp (MIL) during the second consecutive trip in which the diagnostic test has been run and failed.
The PCM will store conditions which were present when the DTC set as Freeze Frame and Fail Records data.

CONDITIONS FOR CLEARING THE MIL/DTC

The PCM will turn the MIL OFF during the third consecutive trip in which the diagnostic has been run and passed.
The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
The DTC can be cleared by using the scan tool Clear Info function or by disconnecting the PCM battery feed.

DIAGNOSTIC AIDS
Check for the following conditions:

Open EGR ignition filter circuit.

An open in the EGR ignition filter circuit will cause EGR Position Error to vary erratically while the EGR valve is operating. With the ignition ON, a test light should illuminate when connected between ground and the EGR ignition filter circuit at the PCM connector. If not, locate and repair the open in the EGR ignition filter circuit.

Excessive deposits on EGR valve pintle or seat.

Remove the EGR valve and check for deposits that may interfere with the EGR valve pintle extending completely or cause the pintle to stick.

Poor connection or damaged harness. Inspect the wiring harness for damage. If the harness appears to be OK, observe the Actual EGR position display on the scan tool while moving connectors and wiring harnesses related to the EGR valve. A change in the display will indicate the location of the malfunction.

Reviewing the Fail Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set

TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table:

Verifies that the malfunction is present.

The PCM contains a recirculation diode which filters the EGR ignition feed for the EGR valve. The recirculation diode is connected to the ignition filter (EGR ignition feed) circuit. If the ignition filter circuit is open, Actual EGR position may be erratic when compared to Desired EGR position. An open in the EGR ignition filter circuit will cause DTC P1406 to be set after an extended period of time.
If DTC P1406 will only set under certain conditions, the malfunction may be intermittent; refer to DTC P1406 Diagnostic Aids. If an intermittent wiring problem is not present, check for a poor connection at the PCM or the EGR valve. If the connections are OK and DTC P1406 continues to set, replace the EGR valve.

This vehicle is equipped with a PCM which utilizes an Electrically Erasable Programmable Read Only Memory (EEPROM). When the PCM is being replaced, the new PCM must be programmed.


------------------------------------------------------------------------------------------------------------------------------
P0301 Code - Cylinder #1 Misfire Detected
A P0301 code means that the the car's computer has detected that one of the engine's cylinders is not firing properly. In this case it's cylinder #1.

Symptoms may include:
the engine may be harder to start
the engine may stumble / stumble, and/or hesitate
other symptoms may also be present

Causes: A code P0301 may mean that one or more of the following has happened:
Faulty spark plug or wire
Faulty coil (pack)
Faulty oxygen sensor(s)
Faulty fuel injector
Burned exhaust valve
Faulty catalytic converter(s)
Running out of fuel
Poor compression
Defective computer

Possible Solutions:
If there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.

If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.


Check it and keep us updated.

May 03, 2011 | 1997 Pontiac Bonneville

1 Answer

I have a 2005 Dodge Dakota V8 4x4 My check engine light turned on. I took the truck to Autozone to have them hook up the machine and see what the problem was. It said I have a bad EGR Valve. I havent...


It can affect mileage, but it might not be the valve. EGR systems tends to get clogged by gunk. Take the valve off and see how dirty things are. If the system is clogged up, take apart as much as you can to clean it up. You can test the valve for operation with a good scanner (autozone doesn't do this--they just tell you the code). Here are instructions from autozone.com:

Linear EGR Valve Diagnosis
The linear EGR valve diagnosis procedure varies depending on the vehicle make and model year. Always follow the recommended procedure in the vehicle manufacturer's service manual. The scan tester may be used to diagnosis a linear EGR valve. The engine should be at normal operating temperature prior to EGR valve diagnosis. Since the linear EGR valve has an EVP sensor, the actual pintle position may be checked on the scan tester. The pintle position should not exceed 3% at idle speed. The scan tester may be operated to command a specific pintle position, such as 75%, and this commanded position should be achieved within two seconds. With the engine idling, select various pintle positions and check the actual pintle position. The pintle position should always be within 10% of the commanded position. When the linear EGR valve does not operate properly:
  • Check the fuse in the 12 V supply wire to the EGR valve.
  • Check for open circuits, grounds, and shorts in the wires connected from the EGR valve winding to the PCM.
  • Use a digital voltmeter to check for 5 v on the reference wire to the evp sensor.
  • Check for excessive resistance in the EVP sensor ground wire.
  • Leave the wiring harness connected to the valve, and remove the valve. Connect a digital voltmeter from the pintle position wire at the EGR valve to ground, and manually push the pintle upward. The voltmeter reading should change from approximately 1 V to 4.5 V.
436f9a1.jpg Linear EGR valve circuit. Courtesy of Chevrolet Motor Division-GMC.
If the EGR valve did not operate properly on the scan tester and tests 1 through 5 are satisfactory, replace the valve.

Here is what your valve looks like:
If you have more questions, please let me know.
a65cb7d.jpg

Oct 13, 2010 | 2005 Dodge Dakota

2 Answers

Chevy pickup 350 vortex code p-1406 comes up can't find what code means in my book. i know it has something to do with manufacturer control auxiliary emissions controls. i don't know where to look for the...


DTC P1406 IS EGR VALVE PINTLE POSITION CIRCUIT MALFUNCTION CONDITIONS.POSSIBLE CAUSE EGR SOLENOID CONTROL CIRCUIT IS OPEN SHORTED TO GROUND OR TO B+ -CHECK EGR VALVE FUSE - OR THE EGR VALVE AND PCM HAS FAILED.

Jul 09, 2010 | 2002 Chevrolet Silverado 1500

2 Answers

EGR Valve pintle intermittently sticking or not opening


possible but the code refers to the valve and or the solenoid to operate the valve
could be a loose / broken wire or bad ground connection
if it is that bad , replace the egr unit complete

Apr 19, 2017 | 1997 GMC Sierra

1 Answer

1996 gmc1500 misses off and on at steady gas pressure or idle.


Try checking the EGR valve for sticking open, sometimes they will cause the missfire code ,, sometimes there will be a small piece of carbon holding the pintle open.. If you can get a data stream on the scantool check egr pintle position the desired position will be different from actual position.. hope ya find it

Sep 24, 2009 | 1996 Chevrolet K1500

1 Answer

1997 blazer sluggish in drive reverse is fine


P0740 is TCC circuit malfunction P0753 is shift solenoid A circuit electrical P0758 is shift solenoid B P1406 is EGR pintle position and P01860 is TCC circuit.

Feb 03, 2009 | 1997 Chevrolet Blazer

Not finding what you are looking for?
1997 Chevrolet K1500 Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...