Question about Cars & Trucks

1 Answer

Radio reset after battery install - Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

You may have to call the dealer. Have your VIN number available. They should give that information to you.

Posted on Jan 22, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How do you reset the radio? What is the code?


notify dealer with vin and proof of ownership for code

Sep 20, 2016 | Suzuki SX4 Cars & Trucks

Tip

Reset the Radio on your 2001-2005 Honda Civic


If the radio on your 2001-2005 Honda Civic (as well as some other Honda products) has lost power for any reason (i.e. dead battery, blown fuse, etc), you will need to enter the reset code.

The reset code for the factory installed radio is located in the glove box. Open the compartment; On the back of the door, usually near the left side, there should be a small white sticker. The sticker has one alph-numeric set and one set containing five numeric digits. The number set with five digits is the reset code for your factory installed radio.

Turn on the radio. When you see "CODE", use the corresponding station pre-set buttons to enter the code. If entered correctly, the radio should active immediately.

on Jul 29, 2010 | Honda Civic Cars & Trucks

2 Answers

How can I unlock the theft lock?


try to do reset procedures.
1. remove positive power cable from battery
2. wait for 5 minutes
3.while waiting for 5 minutes switch on all possible accessory,like ignition,internal lighting,headlights,hazzard,A/C,open all door,step on brake pedals
4. after doing procedure #3 ,switch off all the above mentioned accessories
5.install back the positive power cable to your battery
hopefully this should reset your anit theft system to normal

Sep 05, 2015 | 2006 Pontiac Montana SV6

1 Answer

Hi there after I disconnect the battery on my 2004 Renault espace the radio stop working any ideas please,thanks


Some radios lose the memory when battery power is disconnected so you might have to reset the radio like if you are installing a new one

May 30, 2015 | Renault Espace Cars & Trucks

1 Answer

What are the precautions to take when removing the battery that will not disturb the car radio when you have no resetting disk for a car radio


get a 9 volt battery and cigarette lighter plug and connect the 9 volts battery positive to the center wire in the cigarette plug and negative to the second wire, then plug it into your cigarette lighter socket, then you can remove the car battery and install the new car battery. good luck :)

Oct 14, 2014 | 2005 Ford Fiesta 1.3

1 Answer

The radio no longer plays after installing a new battery, why?


After installing a new battery, lots of things need to be reset.
All the stations you were tuned to will have been lost - I suggest you start by checking the connections to the radio, and trying to re-tune to your stations. If that fails, check the fuse.

Feb 21, 2014 | 2007 Chevrolet Chevrolet Cobalt LS

1 Answer

What steps do you need to go through to replace the battery on a 2006 325xi?


Hi,
Before pulling out the old battery, you should write down the code of your radio so that when you install the new battery the radio will be asking for the operation code.
Replacing battery for that model should be less than 5 minutes to install new one, otherwise everything will be reset.
Hope that helps you out!
thanks for using Fixya!

Dec 17, 2010 | 2006 BMW 3 Series

2 Answers

New Battery installed, need a code to use radio


You can pull the radio and get the codes or call the dealer and get them up to you. You will need your vin # in the window and you will have ti have your name on the registration number before they will give it to you.

Jul 08, 2009 | 1994 Honda Accord

1 Answer

How do you reset the radio for a 2002 GMC 1500?


You will need to contact your local GM dealer with the VIN # proof of ownership & possibly the radio SIN # they will be able to retrieve the code for you if it is the original radio for your truck.
I know it's kind of late now but, If you need to replace your battery & don't have the code I recomend attaching another battery to the battery cables via booster calbes while you install the new battery.

I hope this helps
Farrout!

Mar 17, 2009 | 2002 GMC Sierra 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...