Question about 1996 Mazda Pickup

2 Answers

I have a 96 Mazda B4000 4wd pickup I need door lock cylinder one of mine is broke cant find any know where I could possibly find them. Thanks

I tried dealer jcwhitley almost every parts store I can think of

Posted by on

2 Answers

I would get 2 the same keyed alike from a salvage yard

From there a lock smith maybe able to reprogram if nec

Posted on Jan 21, 2013

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

You could try in some of the organized auto salvage yards especially which have precise part options such as this link - http://www.automotix.net/usedautoparts/1996-mazda-b4000-inventory.html which gives access to a complete inventory for used parts of the '96 B 4000. These are used parts but in good condition which also come with a warranty and free shipping combined with discounts. I get my stuff from them on a regular basis.

Posted on May 15, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 26 Answers

SOURCE: Mazda 5 replacing external handle on sliding door

Your door should be held on with clips. Removing the panel is sometimes hard, just take a good WIDE flat head screwdriver, and whatever tool needed to remove the screws holding the panel on, and be careful. Check underneath the panel, by the inside handle, and the arm point for screws. Once removed, take your WIDE screw driver, and don't quite pry them off, more or less try to get it underneath and pull towards yourself. There is no real easy way, just try to be patient with it, and if you hit any binds, look for more screws, its just a matter of patience for sure.

Posted on Feb 14, 2009

  • 1 Answer

SOURCE: where is the door switch? mine acts like the door isnt closeing and the interior light wont go off

I could not find this switch either, It is actually located in the door latch on the door jam. Switch is somewhere inside. Took my truck to mazda dealer and had it replaced. Anoying problem.

Posted on Sep 17, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: need to know the cylinder number locations on a 2004 Mazda MPV

Does anyone know the cylinder number locations??

Posted on Sep 24, 2009

  • 1 Answer

SOURCE: how do i take the inside cover of the back door of bt50 ute 2009

No assistance required.

Thx
Derek.

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 Toyota Camry keys are not working to open locked door from outside. First the passenger side and now the driver's side door.


Try spraying some silicon lubricant into the keyhole and slide the key in and out a few times.

If this does not work you may have to remove the interior door panel and trouble shoot the lock mechanism.

It's also possible the lock cylinders are worn and need to be rebuilt. This can be done by a qualified locksmith (look for a AAA certified locksmith). Or you can order new lock cylinders and get them re-keyed to match your ignition key.

Dec 16, 2009 | 1996 Toyota Camry

1 Answer

94 mazda B3000 3.0L cylinder head torque specs


Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Sep 17, 2009 | 1994 Mazda 2WD B Series Pickup

1 Answer

I am driving mazda mx-6 1992 but, i cant open my back door i don't know what is wrong


possibly the door lock arm has come off inside the door, if you cant open it from either side that is most probably the problem

May 15, 2009 | Mazda MPV Cars & Trucks

1 Answer

Where is the door switch? mine acts like the door isnt closeing and the interior light wont go off


I could not find this switch either, It is actually located in the door latch on the door jam. Switch is somewhere inside. Took my truck to mazda dealer and had it replaced. Anoying problem.

Apr 23, 2009 | Mazda B-Series Truck Cars & Trucks

1 Answer

1998 mazda B2500 doors wont unlock


The main reason for this is just being used and the little plates in the lock cylinder gets worn and then just keep moving around.

Jan 24, 2009 | 1998 Mazda Pickup

1 Answer

How to replace '96 Ford Explorer driver side exterior door handle


You will need to remove the door panel to gain access to the handle. Roll the window up or down as needed to get to the nuts that attach the handle to the door. You will also need to remove a rod the goes to the door lock. You will see the rod after the door panel is removed. Good luck.

Jan 19, 2009 | 1996 Ford Explorer

1 Answer

1995 chevrolet 2500 4x4 driver door latch operation can't shut do


I think you need to replace the latch assm. The 2 arms that grab the peg are spring loaded and if those springs break the arms won't grab. First try holding the outside door handle in the 'open' position and with your finger or a screwdriver see if you can release the 2 arms. If you can, but they fall back down, then they don't have any spring tension. With your frozen 'lock', if you mean the door lock cylinder you can try spraying wd-40 into it to lubricate it. Also, if your key is worn that may cause the lock cylinder to bind. Hope this helps.

Dec 06, 2008 | 1995 Chevrolet C/K 2500

4 Answers

Code to program my key fob


Here are the program instructions

1. Close the vehicle doors.
2. Turn OFF the ignition.
3. Remove the key from the ignition.
4. Press and hold the driver side door lock switch in the UNLOCK position.
5. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
6. Insert the ignition key into the ignition lock cylinder and remove the key. (Do not turn the ignition key in the lock cylinder.)
7. Insert the ignition key into the ignition lock cylinder. (Do not turn the ignition key in the lock cylinder.) Leave the ignition key in the ignition lock cylinder.
8. Release the door lock switch. The vehicle will sound three beeps in order to verify the Program Mode has been activated.
9. Press the LOCK and UNLOCK buttons together on the keyless entry transmitter and hold until the vehicle beeps twice to verify that the transmitter has been successfully programmed (this take approximately 15 seconds).
10. Perform the previous step to program up to four transmitters (including your old ones).
11. Remove the ignition key in order to exit the Program Mode

Oct 25, 2008 | 1999 Oldsmobile Intrigue

Not finding what you are looking for?
1996 Mazda Pickup Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...