Question about 1996 Acura Integra GS-R

1 Answer

Replaceing fluid after a new clutch in 1996 integra

Where do you fill the trany with new oil

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Filmmaker:

    Uploaded 5 video answers.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 35 Answers

Right side, just behind the axle.

Posted on Apr 28, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How remove and replace clutch slave cylinder 1996 acura integra


10 mm line wrench and a 12 mm wrench or socket. Takes 2 people to bleed it. Look at your master cylinder inside the cabin, they leak too. Most people recommend replacing both at the same time. On a car this old, you might replace the rubber hydralic line too.

Jun 19, 2014 | 1996 Acura Integra GS-R

1 Answer

Where is the trans fill plug on a 1996 dodge avenger


I helped a mechanic,once,to change a transmission mount(?) and in the process he pointed at a plug on the side of the transmission and he said it was where you fill up with fluid (oil or transmission fluid,depends what it uses) you start filling and as you do, you check level by sticking your finger in the hole and stop filling when you feel the tip of your finger get wet.... Good luck and wash your finger afterwards!!!!!

Jan 29, 2013 | 1996 Dodge Avenger

1 Answer

Vw jetta 98 revs shoots up after driving for a few kms


You will need to have the trany checked it may be low on fluid, theres a way of checking the fluid, i would have a job check it or if it a standard shift then the clutch may be slipping and need to be replaced but if its automatic trany then i would have the fluid checked i have run into this problem a few times and it was due to a leak a small leak in the trany oil and when the fluid got low the trany would slip and in some cases not shift or move. hope this is helpful, good luck.

Dec 12, 2010 | 1998 Volkswagen Jetta

3 Answers

Transmission clutches slipping what do we need to do


Take off the oil pan of the trany,check the oil condition,the bottom of the oil pan,see if there is to much metal or clutch parts,you may need to replace it or repair it.check the condition of the filter.

Sep 29, 2010 | 1996 Mercury Grand Marquis

1 Answer

Where do I top up my Toyota Prius Hybrid Transmission


On this would be alot easier on a lift, on the front of the trany theres a fill and drain plug,the top one is the fill, remove the plug and the trany oil should be 0- 5 mm from fill hole, MAKE SURE CAR IS LEVEL!, add if needed, is fluid is needed have car checked for leaks, when installing plug replace gasket with new one and torque to 29 ft lbs.hope this helps,note; make sure to use toyota fluid type ws only.

May 22, 2010 | 2006 Toyota Prius

1 Answer

How do i inject the transmission fluid in the transmission


there is a small filler neck in frt. of the trany , with red cap on it. Brake the cap , there will be a plug under.
Proccedure : engine on idle , take of plug at the bottom of trany oil pan(with engine on idle!!!!! , if engine off , fluid will leak out) , use transfering pump to pump oil in to filler neck untill it starts leaking from bottom plug , wiat till it only drips , put bottom plug back in and torque it. Now you can shut engine off and seal filler neck.
Use only approved trany fluid .This trany takes syntetic fluid.

Apr 22, 2010 | 1996 Volkswagen Jetta

2 Answers

1999 mercury sable trans fluid in radiotor


replace radiator, the trany cooler which is part of radiator is leaking inside radiator, flush cooling system after replacing rad, also i would flush trany also to be 100% sure that theres no coolant in that oil, hope this is helpful,

Dec 13, 2009 | 1999 Mercury Sable

1 Answer

Replacing fluids 0n 1996 300zx


radiator antifreeze: open drain **** on radiator and drain refill with water re plug and leave radiator cap off. start vehicle. watch when coolant drops or rises drastically as that is the thermostat opening. at that time re open drain **** and fill radiator with hose water at the same time. when water coming out is completely clear again turn vehicle off and drain radiator again. fill with antifreeze and water mix. 50/50

oil: jack up car, find oil plug, directly behind steering rack on oil pan. undo plug and drain oil into container. while oil is draining remove oil filter. wait for oil to drain completely then re-install drain plug and new oil filter(filled with oil) undo oil cap and pour in oil 4.5 quarts on n/a and 5 for turbo. tighten cap and your done.

brake system: dont attempt, use an experienced mechanic as the lines need to be bled in numerous places including inside the car from the abs module mounted behind the passenger seat.
easy brake system: individually bleed brakes while adding fluid until clear fluid comes out. (not efficient)

a/c: do not attempt unless you have an evac pump for ac systems.

clutch: same as easy brake except using the bleed valves at the slave cylinder and on passenger side fender well.

washer fluid: add fluid and squirt a little to make sure there is no air in the line

Jul 18, 2009 | 1996 Nissan 300ZX

1 Answer

Clutch not responding


well if you have mixed a wrong type of fluid (such as power steering or oils) you are going to have to replace the clutch master cylinder and slave cylinder. Before you install the new parts be sure to drain all the old fluid out of the clutch line, and flush the clutch line with brake cleaner and blow compressed air thru until its clean and dry. install your new parts and fill with fresh (NEW) fluid whatever the manufacturer recommends most any DOT 3 or DOT 4 brake fluids will work (read the cap on the resivoir) and proceed with bleeding the air from the system, i usually fill up the resivoir with the bleed screw open(on the slave) until fluid with no air comes out and then proceed with the bleeding process this is called gravity bleeding and will help speed things along be sure to rate this and good luck this is not very hard to do and should take about an hour HERE IS THE MASTER
AND HERE IS THE SLAVE about $80 in parts altogether including fluid please rate _JEFF

Sep 13, 2008 | 1996 Toyota Camry

Not finding what you are looking for?
1996 Acura Integra GS-R Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...