Question about Acura MDX

Open Question

Where is the crankshaft position sensor on a 2001 Acura MDX

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 218 Answers

SOURCE: the location of the cps on a 2001 ml430

IT IS IN THE REAR OF THE ENGINE WHERE IT MOUNTS TO THE TRANSMISSION.THE SENSOR READS THE NOTCHES ON THE FLYWHEEL.ABOUT A 1/2 HOUR JOB.

Posted on May 07, 2009

Ad
  • 135 Answers

SOURCE: Need to replace both crankshaft position sensors 2001 Cadillac

4.6 the twocrankshaft position sensors are located on the front of the block just above and to the left of the oil filter. not hard to replace.

Posted on May 19, 2009

  • 1348 Answers

SOURCE: acura mdx 2005

30000 miles.the owners manual will tell you exactly.most honda are 48000 km,exception is the cvt type transmission which there is no service done.

Posted on May 26, 2009

  • 248 Answers

SOURCE: where are the camshaft and crankshaft position

crankshaft sensor is and the hormonic balance pulley and cam sesoor should b and the front of the motor toward the top. But to b sure u should get a book for u vehical

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram rear main seal


Don't need a diagram, you have to pull the transmission to replace the seal. It is the seal in the engine block that goes around the crankshaft output to the transmission.

Jul 31, 2014 | 2001 Acura MDX

1 Answer

How to change rear main engine seal on acura mdx 2001


http://www.mdxers.org/forums/73-2001-2006-acura-mdx/47786-mdx-transmission-rear-main-seal-diy-tutorial.html

Jul 31, 2014 | 2001 Acura MDX

1 Answer

2001 MDX will not idle


Error Code: P0221
Description:
Throttle Position (TP) Switch/Sensor B
Accelerator Pedal Position (APP) Switch/Sensor B Range/Performance Problem
Possible Cause:
- Accelerator cable adjustment.
- Throttle position (TP) switch/sensor .
- Accelerator pedal position (APP) switch/sensor.
- Check valve clearance, adjust if required.

Mar 03, 2014 | 2001 Acura MDX

1 Answer

Where is crankshaft position sensor?


Here's your best step to take,click on link.Plus you will have it for other things,got one for all my vehicles.

Aug 30, 2013 | 2002 Acura MDX

1 Answer

My 2001 Acura MDX automatically disengage to neutra from gear four.I have service the gear,change the gear sensor and the fibers,still the problem persist.what is the way out?ensor


Hi,
Acura and Honda have a KNOWN Issue w/the Torque Converter in the Automatic Transmission. Very likely you'll need to have it rebuilt....may be cheaper to trade it in on a newer car.

Search for 'Acura automatic transmission issues' online.

Td

Nov 13, 2012 | 2001 Acura MDX

1 Answer

Changing cabin airfilter for a 2001 acura mdx


It is. I believe on your MDX you have to remove the glovebox 10mm screws. Then there is a drawer in the plastic HVAC housing that unclips on both sides and slides out. If it hasn't been changed before, on most Honda and Acura SUVs you have to carefully cut the plastic that covers the support to remove the metal bar to get to the drawer. You need to keep the plastic because it screw into it's old position after the job is complete.

Mar 12, 2009 | 2001 Acura MDX

2 Answers

Camshaft position sensor location


crank sensor is a component used in an internal combustion engine to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control ignition system timing and other engine parameters. Before electronic crank sensors were available, the distributor would have to be manually adjusted to a timing mark on the engine.

The crank sensor can be used in combination with a similar camshaft position sensor to monitor the relationship between the pistons and valves in the engine, which is particularly important in engines with variable valve timing. It is also commonly the primary source for the measurement of engine speed in revolutions per minute.

Crank sensors in engines are usually comprised of magnets and an inductive coil. They are principally based on the Hall effect. Common mounting locations include the main crank pulley, the flywheel, or occasionally on the crankshaft itself.

Some engines, such as GM's Premium V family utilise crank position sensors which read a reluctor ring integral to the Harmonic Balancer. This is a much more accurate method of determining the position of the crankshaft, and allows the computer to determine within a few degrees the exact position of the crankshaft (and thereby all connected components) at any given time.

Dec 27, 2008 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...