Question about Cars & Trucks

1 Answer

After running for awhile engine cuts out troybuilt model 12a-466n063/700

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,103 Answers

Check electronic ignition module for possible overheatig and replacement.. also be sure the coolig fins on the block are not full of dirt...can clean out with compressed air..repost findings and oil level is full also....

Posted on Jan 21, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 1999 rodeo had a knocking sound, now it's pounding sound

Sounds like major bearing failure caused by lack of oil. You will probably need a new engine

Aug 04, 2016 | Cars & Trucks

1 Answer

Engine cuts off after start

have a load test done on the battery as you have a dead cell and the alternator cannot produce enough current to feed the dead cell and the ignition system at idle.

Dec 26, 2013 | Cars & Trucks

2 Answers

I have 85 rx7 12a engine carb getting spark and fuel,it will turn but it won't start what could it be.

It takes 3 things for a car to run... spark, fuel, and air. Sounds like you should be looking for a problem with the air, IF it is getting spark and fuel. Food for thought.

Feb 29, 2012 | 1985 Mazda RX-7

1 Answer

91 primera sr18 Di,have fixed vacume leak's in inletmainfold,replaced the airflow meter,have got it running excellently but after it has been running for awhile,it randomly dies and wont start again f

I had a similar problem. Nissan sr18di engine. car would run fine and randomly engine would cut off and only start after 20 minutes. Changed distributer
fine since

Nov 09, 2011 | Cars & Trucks

1 Answer


The code p1391 is telling you that your ckp/cmp sensor signal is lost. What it is saying in normal terms is that the (crankshaft position sensor and the camshaft position sensor) are not sending a signal from time to time. That is why the car cuts out and will not start. First thing is to look at both sensors and check the wireing to each for any damage. The ckp is located on the front of motor on bottom side. The cmp sensor is located on the back of engine near the top. You have either one or both sensors that are not giving a signal to the pcm (power control module ). Hope this will help.

May 30, 2010 | 2001 Dodge Neon

1 Answer

My 2005 Nissan cuts off and will not start until the engine cools

I would try getting an active diagnostic scan done on the vehicle but it sounds like it has something to do with the ignition system possibly an ignition control module or another sensor.

Aug 27, 2009 | 2005 Nissan Altima

1 Answer

After recharging with red tech 12a the compressor cuts in and out and the idle goes up and down. The gage on the low side at idle reads 55 and with the AC off goes up to 110.What did I do wrong?

You didn't state what year the car was. If it's in the 90's or 2000's, It takes the R134A freon, not the 12A, and it should have been charged on the low side, not the high side.

Jul 16, 2009 | 2000 Saturn L-Series

1 Answer

1994 honda accord will start runs awhile then cuts out .

Could be fuel delivery; fuel filter clogged, worn fuel pump.
Does it still have battery power when it dies, cranks but no start? How long does it take to start again? When does this occur, engine hot/cold? Does it happen all the time or sometimes? How long does it run until it cuts?

Jun 11, 2009 | 1994 Honda Accord

1 Answer

How to identify what engine I have

there are two models of engine in this year one is a 1.1 liter
and the other is a 1.3 liter both rotary engine
you can identify them like this

the 1.1L engine is a 4 brl carbureted engine
the 1.3L engine is fuel injection

yours is a 12a = 1.1 liter rotary carbureted engine
the 1.3l is a 13b engine code fuel injected

Have a great day !!!!


Dec 11, 2008 | 1984 Mazda RX-7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14548 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides