Question about Cars & Trucks

1 Answer

Ford ranger wont start but if you put starting fluied it fires

New fule pumps new regulator have power to all and have reset inerta switch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,904 Answers

I would check the fuel pump and the fuel relay.

Posted on Jan 21, 2013

  • Dallen Jan 21, 2013

    Already put in new fuel pumps, put new fuel regulator in, can start it with ether, and checked the intermittant switch, have 40 psi on the fuel rail, still won't start...

  • Dallen Jan 21, 2013

    What is the function of the typical manifold absolute pressure sensor?

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

rainstreet
  • 1 Answer

SOURCE: MY FORD EXPLORER WONT START

fuel pump relay

Posted on Dec 17, 2008

  • 1114 Answers

SOURCE: 93 ford tempo v-6 replaced fuel pump but will not start did reset

by chance the replacement pump you used was it a "CARTER" brand I had one of those quit the same day installed it! also be sure that the feed wire on pump in tank is connected properly! you can change them by taking out the back seat of car!! the seat has 2 clips good luck

Posted on Dec 22, 2008

  • 74 Answers

SOURCE: 1998 ford ranger xlt

p0102= mass air flow sensor is dirty or needs to be changed.
p0232= recheck your wiring. you might have crossed wires when changing fuel pump or your fuel sensor might be faulty

Posted on Feb 18, 2009

VREGG
  • 41 Answers

SOURCE: 98 chevy camaro wont start how do you reset fuel pump regulator ran out of gas

BLEED INJECTOR SYSTEM NOT GETTING FUEL TO ENGINE TOP.

Posted on May 08, 2009

  • 1986 Answers

SOURCE: wont start wheres the reset button for fuel pump

I believe it should be in the passenger side kick panel or somewhere around there

Posted on Sep 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1987 ford wont start, will turn over,put in new gas tank pump new relays reset accater and will not pick up fuel from tank and new frame rail pump no gas anywhere


There is an Inertia switch which cuts off the power to the fuel pump. As you did not describe your model, look on the internet by searching the term "inertia switch location" and then put in your model. Also the crankshaft position sensor tells the engine that you are turning RPM. This regulates gas pressure and sometimes does not create a code to indicate this part failed.

Aug 23, 2015 | Ford Cars & Trucks

2 Answers

How do i toubleshoot my ford ranger cranks but wont start


What year? Inertia switch tripped. Fuel air spark compression. I have seen inerta switches plugs pulled out on the passenger side floor board many times. People's feet.

Dec 11, 2014 | Ford Cars & Trucks

1 Answer

No power to fuel pump when key is on 1987 ford ranger


ck the inertia switch located on the foot wal under the carpet

Sep 11, 2014 | 1987 Ford Ranger

2 Answers

Why is my 1987 ford ranger acking iike its loosing fule pressurs win diving


It may BE losing fuel pressure, Robert. Check the fuel pressure and flow rate at the fuel rail. Filter, plugs, and cap have nothing to do with fuel pressure - your fuel pump and pressure regulator are the only things that can change fuel pressure very much.

Aug 08, 2014 | 1987 Ford Ranger

1 Answer

1994 ford ranger ran ot of gas now won't start. Put fuel in it made sure saftey switch (reset switch) was okay. But still wont start. Fuel pump seems to be working. Any suggestions ...


Do you know what the fuel pressure is at?

Try this. While somebody cranks the engine over whack the bottom of the fuel tank (about dead center) with a rubber mallet. If the vehicle starts replace the pump. The fuel pump is kept cool by the fuel in the tank. Running the tank dry is hard on the fuel pump.

May 04, 2011 | 1994 Ford Ranger Supercab

1 Answer

I have a 95 ford ranger 3.0 The fuel pump will not will not pump (run) I have checked the fuse and relay. I have also check the inerta switch and it checked ok. the ignition switch checked ok. What...


The next step is to take a 12v test light and check for power+ground at the tank, if you've got power and a good ground but still no sound from the pump, then it's time to replace it.(be sure the key is on while testing) hope this helps.

Sep 18, 2010 | Ford Ranger Cars & Trucks

1 Answer

I have a 1998 ford wind star new fule pump but still not geting fule , wont crank engine turns ove but won;t start


INSTALL PRESSURE GUAGE THEN CK, VOLTAGE TO PUMP PCM TURNS ON PUMP RELAY FOR 2 SECONDS WHEN KEY CYCLED ON ,, IF NO POWER CK INERTIA SWITCH ( MAY BE TRIPPED ) IF NO POWER TO INERTIA SWITCH CK FUEL PUMP RELAY IF NO VOLTAGE AT PUMP RELAY THEN CHECK FOR SPARK AT PLUGS IF NO SPARK CK PCM POWER RELAY IT SUPPLIES VOLTAGE TO PCM THAT INTURN POWERS FUEL PUMP RELAY

HOPE THIS HELPS

Aug 08, 2010 | 1998 Ford Windstar

1 Answer

Get spark, but no power to new fuel pump 1999 ford Ranger


the inertia switch is in front of the passenger seat, bolted to the fire wall, hidden by the carpet on an 89 and behind the kick panel on the 99. 99 should have a picture that looks like a gas station pump with a line thru it. pull panel off, push big red button. on 89 its the little grey button on the top.

Oct 03, 2009 | 1989 Ford Ranger

2 Answers

Stalls when giving it gas


these were hard to fix when they were new in 1990, question:::: does it run and rev-up hi normally in neutral/park??? with a timing light does the distributor show full advance???you claim "CUTS-OUT", like back-firing ??you may need to test the COIL, TPS (throttle position sensor) and LOOM to isolate the cause,.. try those and let me know the outcome....GL

Jul 06, 2009 | 1990 Ford Ranger SuperCab

1 Answer

Have a 86 ford ranger 2.3 l 4cy in mornings


its your fule filter theres 2 of them i the 86 ford ranger you need to change them the location of the fule filters are on google just tipe in fule filter 1986 ford ranger location it should pop up there about 8 dollors a peace easy fix and your truck is like new also get a new battey if you havent k have a good day. oh i know this because i own one had the same problem

Apr 02, 2009 | 1986 Ford Ranger 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...