Question about 2005 Chrysler 300

Open Question

2006 Electronic Throttle control light

The ETC light in my Chrysler 300 is coming on. It happens when I am at a stop, car is idling, and simultaneous the Traction Control light comes on. Less than 11 months ago Chrysler dealer identified code P1001 as a short runner valve binding and the valve cover gaskets and upper intake maniford replaced. This visit cost me $3009.92. Last month repaired a vaccum leak and EGR gasket. This car just hit 60K...Any advice.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Where is the EGR valve

I saw on another forum...that it is on the rear of the motor on the passenger side. It also stated that it is easy to replace. I haven't looked yet.

Posted on Aug 19, 2008

Ad
  • 1 Answer

SOURCE: Engine Light On - 2006 Chrysler 300 3.5 engine

I have a 2005 Chrysler 300. The engine light comes on from time to time -- sometimes it will stay on for a week or so and then go off for at most a day or two. I had the code read yesterday and the feedback was "EGR pressure flow is low." My car has about 65K miles. Is this a typical problem with this car? I was told replacing the EGR valve would fix the problem. How easy is it to replace an EGR valve on this vehicle? Once replaced, do I need to reset the computer --- if so how do I do this? If it is easy to fix, could you please provide step by step directions and show me location of the part in question that needs replaced?

Posted on Apr 10, 2009

  • 14036 Answers

SOURCE: I HAVE A 2003 CHRYSLER 300M SPECIAL 3.5HO AND

yep po132 shorted to voltage po152 shorted to voltage.this means lean conditions .you got in take leak .if you get a high voltage conditions you got rich mixture.bad plugs or stop up air filter.

Posted on May 01, 2009

  • 412 Answers

SOURCE: 2005 Chrysler T&C EGR valve solenoid problem

YOU NEED TO DISCONNECT THE BATTERY FOR 5-10 MINUTES FOR FAULTS TO CLEAR COMPLETELY..HAVE SEEN THIS PROBLEM BEFORE AFTER REPLACING AN EGR VALVE..IT WAS A TECH TIP FROM CHRYSLER ENGINEERING..THE EGR VALVE WAS THE PROBLEM,BUT THE PCM WOULD NOT LET THE CODES GO EVEN AFTER CLEARING THEM WITH SCAN TOOL..ALSO CHECK CONNECTIONS AT EGR CONNECTOR FOR SPREAD PINS

Posted on Jul 26, 2009

c17hydro
  • 2984 Answers

SOURCE: need to replace a idle air control valve on a 1999 300M Chrysler

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the IAC electrical connector.
  3. Remove the IAC mounting screws.
  4. Remove the IAC.



da3669e.gif

To install:
  1. Install the IAC to the throttle body.
  2. Tighten mounting screws to 5.1 Nm (45 inch lbs.) torque.
  3. Attach electrical connector to the IAC.
  4. Connect the negative battery cable.
  1. Disconnect electrical connector from IAC motor.
  2. Disconnect air plenum (where applicable).
  3. Remove two mounting bolts (screws).
  4. Remove IAC motor from throttle body.

3ccd55e.gif

To install:
  1. Install IAC motor to throttle body.
  2. Install and tighten two mounting bolts (screws) to 60 inch lbs. (7 Nm) torque.
  3. Install electrical connector.
  4. Connect air plenum (where applicable).

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn off electronic throttle control light


Well ---- you obviously know you need to check
for OBD Codes & diagnose the issue &
resolve the problem

Oct 20, 2014 | 2006 Chrysler 300

1 Answer

Chrysler 300 2006 v-6 tps light on dash


Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Oct 08, 2012 | Chrysler 300 Cars & Trucks

1 Answer

Etc light on 2009 Chrysler 300


Whenever this warning or any other stays on in the dash it is indicating that the systems control module has detected a fault, it then disables the system as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Oct 04, 2012 | 2009 Chrysler 300

1 Answer

Starting problems with 2006 Chrysler 300 3.5 v6


Hello 2006 Chrysler,

If your talking about the component that is located along the air duct run from the air filter to the throttle body it is caled a MAF sensor.
Mass Air Flow Sensors Components

Jul 23, 2017 | 2006 Chrysler 300

1 Answer

2006 Chrysler 300C starts but then dies out?


Can you describe the light? Based on the symptoms, one possibility is the Electronic Throttle Control light - a lightning bolt with a curved line on either side. This indicates that the electronic throttle control is not working properly, and will require service to repair the problem. Recommend you do not try to drive, as you will have no control over the throttle/engine speed.

Dec 11, 2011 | 2006 Chrysler 300 C

1 Answer

First the etc light came on and then the mil light


Have you checked to see if the gas cap is on tight. New cars have a pressurized gas tank. It will set a light if it doesn't seal good.

May 17, 2010 | 2005 Chrysler 300

4 Answers

My electronic throttle control warning light came on what is wrong with my 2007 Sebring?


I have an 08 Sebring and mine has been having the etc light come on and the car will stall..with little to no notice. It's at the dealer right now and they can't figure out what is causing this because the light doesn't stay on once you turn off the car and restart it. It's kind of relieving to me that someone else is having this problem. Hopefully Chrysler can figure out what the deal is with this!!

Mar 01, 2010 | 2007 Chrysler Sebring Sedan

Not finding what you are looking for?
2005 Chrysler 300 Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...