Question about 1998 Lincoln Town Car

2 Answers

Heater core how to replace heater core in a 1994 lincoln town car? thank you.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Bad news for you because you may have to take the dash apart on the pass side to pull heater core a shop wasnts about $600 in labor but it can be done i did on my 1993 good luck

Posted on Jan 27, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

It is better if you take it to a shop . the entire dash has to come out and be put aside or you'll never get it out of the car sorry .i have done this mant times and that is the easyiest way or you'll find yourself ruining a new heater core

Posted on Jan 27, 2009

4 Suggested Answers

  • 193 Answers

SOURCE: 1989 Lincoln Town Car Heater core

Go to Autozone and purchase a Clymer repair manuel. It will show how to remove the dash. You need to find all the screws.

Posted on Nov 22, 2008

  • 333 Answers

SOURCE: Heater core - 1996 Lincoln Town Car

  1. Disconnect the negative battery cable.
  2. Drain the cooling system and disconnect the heater hoses from the heater core tubes. Plug the hoses and the heater core tubes to prevent coolant leakage.
  3. Remove the 3 nuts located below the windshield wiper motor attaching the left end of the plenum to the dash panel. Remove the 1 nut retaining the upper left corner of the evaporator case to the dash panel.
  4. Disconnect the vacuum supply hose(s) from the vacuum source. Push the grommet and vacuum supply hose(s) into the passenger compartment.
  5. Remove the right and left lower instrument panel insulators.
  6. On 1990-00 vehicles:
    1. Remove the cross body brace and disconnect the wiring harness from the temperature blend door actuator.
    2. Disconnect the ATC sensor tube from the evaporator case connector.
  7. Disconnect the vacuum jumper harness at the multiple vacuum connector near the floor air distribution duct. Disconnect the white vacuum hose from the outside-recirculating door vacuum motor.
  8. Remove the 2 hush panels.
  9. Remove 1 plastic push fastener retaining the floor air distribution duct to the left end of the plenum. Remove the left screw and loosen the right screw on the rear face of the plenum and remove the floor air distribution duct.
  10. Remove the 2 nuts from the 2 studs along the lower flange of the plenum.
  11. Carefully move the plenum rearward to allow the heater core tubes and the stud at the top of the plenum to clear the holes in the dash panel. Remove the plenum from the vehicle by rotating the top of the plenum forward, down and out from under the instrument panel. Carefully pull the lower edge of the instrument panel rearward, as necessary, while rolling the plenum from behind the instrument panel.
  12. Remove the 4 retaining screws from the heater core cover and remove the cover from the plenum assembly. Pull the heater core and seal assembly from the plenum assembly.
To install:
  1. Carefully install the heater core and seal assembly into the plenum assembly. Visually check to ensure that the core seal is properly positioned. Position the heater core cover and install the 4 retaining screws.
  2. Route the vacuum supply hose through the dash panel and seat the grommet in the opening.
  3. Position the plenum under the instrument panel with the register duct opening up and the heater core tubes down. Rotate the plenum up behind the instrument panel and position the plenum to the dash panel. Insert the heater core tubes and mounting studs through their respective holes in the dash panel and the evaporator case.
  4. Install the 3 nuts on the studs along the lower flange and one on the upper flange of the plenum. Install the 3 nuts below the windshield wiper motor to attach the left end of the plenum to the dash panel and the one nut to retain the upper left corner of the evaporator case to the dash panel.
  5. Position the floor air distribution duct on the plenum. Install the 2 screws and plastic push fastener. If removed, position the panel door vacuum motor to the mounting bracket and install the 2 attaching screws.
  6. Connect the white vacuum hose to the outside-recirculating door vacuum motor. Connect the vacuum jumper harness to the plenum harness at the multiple vacuum connector near the floor air distribution duct. Install the floor duct.
  7. If equipped with manual air conditioning, connect the temperature control cable housing to the bracket on top of the plenum and connect the temperature control cable to the temperature blend door crank arm. Adjust the temperature cable.
  8. If equipped with ATC, proceed as follows:
  9. Connect the temperature control cable to the ATC sensor and adjust the cable. Route and connect the vacuum harness connector to the ATC sensor and connect the electrical connector to the ATC servo connector. Do not block the sensor aspirator exhaust port with the excess vacuum harness. Install the ATC sensor tube between the sensor and the evaporator connector.
  10. On 1990-00vehicles:
    1. Connect the ATC sensor tube to the evaporator case connector.
    2. Install the cross body brace and connect the wiring harness to the blend door actuator.
    3. Install the bolt to attach the lower right end of the instrument panel to the side cowl. Install the right side cowl trim panel and tighten the right door sill plate attaching screws.
  11. Connect the vacuum supply hose(s) to the vacuum source.
  12. Install the right and left lower instrument panel insulators and install the 2 hush panels.
  13. Unplug the heater core tubes and the heater hoses and connect the heater hoses to the heater core tubes. Fill the cooling system.
  14. Connect the negative battery cable and check the system for proper operation. I hope this helps. Don,t forget to rate my answer.

Posted on Mar 01, 2009

  • 610 Answers

SOURCE: heater blows only cols air-

sounds like a restricted heater core. if you remove the heater hoses from the engine, pour some cooling system cleaner in. let it sit for 10 or 20 minutes, then you can flush with a garden hose.

Posted on Dec 18, 2010

weekspena
  • 375 Answers

SOURCE: Where is the heater core located on a 1994 Lincoln

behind glove box!
Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing

  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core.
Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Posted on Jan 13, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater core replacement in a 2000 lincoln town car


remove the whole dash to get the heater unit out ,sorry no short cuts available

Jan 28, 2012 | 2000 Lincoln Town Car

1 Answer

Replace the heater core in a 2000 lincoln town car


For heater core replacing procedure.I suggest you to go through this related help links.Its all complete step by step procedure :----How to replace heater core for All car models?

Click the link below:---

http://technoanswers.blogspot.com/2011/11/how-to-replace-heater-core-for-all-car.html

--------------
How to Flush Heater Core?

http://schematicsdiagram.blogspot.com/2011/12/how-to-flush-heater-core.html

---------------
How to Remove Heater Core ?

http://howtobyme.blogspot.com/2011/12/how-to-remove-heater-core-on-2008-honda.html
Heater Core Replacement?

http://howtobyme.blogspot.com/2011/12/honda-heater-core-replacement.html

------------
To replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on.html------How to replace heater core?http://technoanswers.blogspot.in/2012/02/how-to-replace-heater-core-on_10.html
----------This will help.Thanks.

Jan 28, 2012 | 2000 Lincoln Town Car

1 Answer

Heater blows only cols air- one line going into heater core is hot, the other cold.....1994 lincoln town car


sounds like a restricted heater core. if you remove the heater hoses from the engine, pour some cooling system cleaner in. let it sit for 10 or 20 minutes, then you can flush with a garden hose.

Dec 18, 2010 | Lincoln Town Car Cars & Trucks

1 Answer

Where is the heater core located on a 1994 Lincoln Town Car?


behind glove box!
Inspect/Replace If it is necessary to remove the heater assembly, the cooling system must be drained before removing the heater core.
When a heater core leaks, a new heater core is installed or the old one repaired.
Heater Housing
  • The heater housing is usually under the dash and must be removed to gain access to the heater core.
  • Procedures for replacing the heater core vary with the year, make, and model of car. It threfore necessary to consult the manufacturer's repair manuals for the proper procedure for replacement.
f74-01.gif The heater housing is disassembled to get to the heater core.
Heater Core
  • Remove the access panels(s) or the split heater/air conditioning case to gain acess to the heater core.
  • Remove the heater coolant hoses.
  • Remove the cable and/or vacuum control lines (if equipped).
  • Remove the heater core securing brackets and/or clamps.
  • Lift the core from the case. Do not use force. Take care not to damage the fins of the heater core when removing.
  • To reinstall the heater core, reverse the removal steps.
When the heater core leaks and must be repaired or replaced, it is a very difficult and time-consuming job primarily because of the core's location deep within the firewall of the car. For this reason always leak test a replacement heater core before installation.

Dec 02, 2010 | 1994 Lincoln Town Car

1 Answer

Heter core liking


This is a very time consuming job and not for someone that doesnt like to undertake the tuff stuff.The dash has to be pulled to replace the heater core and the ac must beevacuated and recharged

Mar 28, 2010 | 1994 Lincoln Town Car

1 Answer

Heater door dont change to cool


this problem is due to a failed temperature control blend door actuator motor, this part in located about center of the dash on the air duck between the heater core and evaporator core, you must remove the dash Assembly to replace it.

Aug 05, 2009 | 1994 Lincoln Town Car

1 Answer

Heater core


I would recommend picking up a Haynes repair manual for your year and make of Lincoln, I have one for my Lincoln and it gives you all the instructions and troubleshooting hints and the estimate time is anywhere from 5-10 hours

Feb 20, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
1998 Lincoln Town Car Logo

461 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...