Question about Cars & Trucks

Open Question

2001 CRD Grand Voyager - Clutch won't disengage.

We have a 2001 CRD (2.5 diesel, manual transmission) Grand Voyager. We've recently (last 4 months) had the clutch replaced as it was slipping, but suddenly today, whilst out, the clutch won't disengage at all (can't select a gear with engine running & when car is started in 1st gear with the clutch pedal depressed, the car lurches forward as if clutch pedal is released). I believe the clutch on these is hydraulic,could it be a fluid problem ? If so is the master cylinder sealed or accessible to bleed / top up the fluid ? Thank you.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 566 Answers

SOURCE: GEARBOX WONT GO INTO GEAR

hi from uk could you please give a little more info ? what make/model car ? has this problem occured suddenly? has car been layed up off road some time prior to this unable to select gears ? this problem sounds very much like the clutch drive plate is either stuck to flywheel hence question above ? or it is sticking on primary/spigot shaft for some reason and failing to disengage drive to g/box? how does clutch pedal feel ? you might try selecting 2nd gear with clutch fully pressed and h/brake on then try starting engine if engine starts ?runs then put slight revs on and slip clutch a few times this may work if plate is sticking? if you come back with update may be able to advise further

Posted on Dec 24, 2008

Ad
  • 1596 Answers

SOURCE: rover 600 1997 not engaging any gears when clutch fully depressed

Sounds like the SLave Cylinder has givin up Possible the Reli=eice Bearing I ALWAYS Replace As A PAIR . If you can put in gear by having someone rock the car front to back and it holds well its pretty Obvious that you DO have A Clutch Master Cylinder or Clutch Slave aat Releice Bearing Problem AGAIN These Parts I REPLACE AS A PAIR. Before ANything Chech Fluid Level that will tell the store IF FULL Most Probably MASTER-- If EMPTY then See where it went Look At SLAVE if wet thats the Culpret. --->> I Hope this INFO helps you and have a good Day >> Please dont forget to RATE me ok ? Thank You

Posted on Jan 16, 2009

  • 34 Answers

SOURCE: 2001 VW Jetta 1.8L Manual Transmission

Check the fluid make sure its at the right level.

Posted on Mar 14, 2009

germcelchar
  • 389 Answers

SOURCE: 2002 Hyundai Accent won't go into gear.

Probably the arm that holds the rtelease bearing in the bell housing has slipped out of place. Get someone to depress the clutch while you check the arm is not loose. If the cylinders are working then its most likely the arm is disconected. If you are lucky you may get it put back in place by looking through the inspection hole but most likely you will have to seperate the engine and gearbox. Sorry I havent better news for you.

Posted on Aug 07, 2009

  • 157 Answers

SOURCE: Clutch pedal does not disengage clutch

If the car hasn't been driven for a while it could be corrosion on the fork but I think that is unlikely. I think you are right about the release bearing being jammed in the spring. If the truck has quite high mileage, it probably means a clutch job.

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep Cherokee 2.8 crd outo box does not engage. It disengaged while driving, now no gears available


is this a transmission problem. this non USA car.
if yes, which one you got.? a/t or m/t and which one.

what year car.
crd diesel.
the cherokee ended here in 2001
but the Lliberty is sold outside USA as a "Cherokee' odd as that is.
and with the CRD (of some type)

no gears, smackes of stick shift. after all A/T never shift gears
they use clutches totally, (but have plenary gear sets)
"NO gears ," does hat mean its stuck in neutral or the wrong gear.
if in neutral the foot clutch slave is leaking, lost all clutch fluid from the filler?
if the gear shift fails to shift, that is another matter, are all gears dead ? and stuck in netural?

May 04, 2015 | Jeep Cars & Trucks

1 Answer

2001 CRD Grand Voyager - clutch won't disengage.


Is there any fluid on the ground near the transmission? It's possible the clutch actuating cylinder has failed. If it was air in the line you would have noticed it the day you got it back. The master cylinder is on the firewall next to the brake master. You can add fluid if it's low. If it's empty then there may be a loose fitting or the bleeder screw on the actuating cylinder may be loose too.

Aug 09, 2017 | Chrysler Voyager Cars & Trucks

1 Answer

Manual transmission won't go into gear


Sounds like the clutch disc is toast.
Its possible the throw-out bearing has failed, but either way the transmission has to come out to fix either part.

Dec 24, 2012 | 2008 Subaru Forester

1 Answer

2004 Jeep Grand Cherokee CRD 2.7L injector seal leak issue


I would contact the dealer and see if the parts dept has a revised seal.

Jun 14, 2012 | Cars & Trucks

1 Answer

Transmission will not go into any gear


Stick a magnet on your pedal and if it doesn\'t stick then it\'s the OEM pedal and should be replaced with the steel pedal.

Pontiac had this \'awesome\' idea to make the clutch pedal out of aluminum and after 20 years the pedal actually starts to bend and bottom out on the floorboard before giving you all of the travel necessary to disengage the clutch. Fierostore.com sells a replacement pedal for about 50 bucks. This is the first place I would start since it is what fixed my 1986 Fiero GT 4spd.

If the problem is still manifesting then move onto bleeding/replacing the clutch master/slave cylinders.

I\'ve also seen the brackets on the transmission that the shift and select cables attach to have worn out and introduced a bunch of slop in the shifter, but this is less common.

I\'ve also seen the clutch release bearing seize because of a broken release bearing fork slipping around the collar and grabbing the freely rotating part of the bearing. This then leads to pressure plate fingers breaking off and soon no matter how hard you push, the clutch won\'t disengage. Tranny has to come out. Seen this once.

And last but not least, I\'ve also seen a nut on the inside of the transmission shift/select shaft come loose and leave the tranny stuck in the 3/4 fork. Seen this one time 5 years ago.

Good luck,

Rebel Faggioli

May 12, 2012 | 1986 Pontiac Fiero

1 Answer

Gear box oil


my granddad has a voyager LX CRD, he has problems with getting the car into gear, as he says if you are lazy (cutting corners on the gearbox) it won't go into gear. we checked the gearbox oil and it was low and also it seemed that it was transmission fluid (for an automatic car) ALTHOUGH my granddads car was a manual. this is the one thing that chrysler don't come first for - Manual Cars
hope i helped you

Apr 15, 2012 | 2002 Chrysler Voyager

1 Answer

I need an owners manual in English for JEEP GRAND CHEROKEE LIMITED 2.7 DIESEL CRD from 2002. My email address is folitek@mt.net.mk


You could try
http://www.mauritron2.com/service_manuals.html
or
http://www.mauritron2.com/operating_guides.html
We've used them in the past and found them very good.

Also if it is not listed then ask via the link

Aug 03, 2011 | 2002 Jeep Grand Cherokee

1 Answer

Where is the fuel filter on a chrysler grand voyager 2.5 crd diesel


Look underneath near one side or the other. Probably about midway back toward the gas tank.

Oct 05, 2010 | 2000 Chrysler Grand Voyager

3 Answers

Chrysler voyager clutch judder, have replaced clutch and flywheel but still judders mainly in reverse


You should flush the transmission out. Remember mopar uses high friction trans fluid and when this fluid gets somewhat old and looses friction then it will not operate properly.

Jun 19, 2010 | 2000 Chrysler Grand Voyager

1 Answer

Chrysler voyager crd


You must check the fluid right on the transmission because its a manual.

Aug 21, 2008 | 2001 Chrysler Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...