Question about 1994 Jeep Cherokee

Open Question

Fuel pressure specs on 1994 jeep 4.0

Fuel pressue specs

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
michigan man
  • 3533 Answers

SOURCE: low oil pressure

the first i would do is to see if the oil sending unit is ok and if you gage is working right and if they are then checkout the oil pump.

Posted on Feb 14, 2009

Ad
  • 6982 Answers

SOURCE: torque specs on 1994 jeep

Main bearings at 80 foot lbs. rod bearings at 30 foot pounds. Make sure you check clearances with plastigage before you button it up and light it. Anything out of clearance may require an over or undersized bearing. Also, on final install, use a swipe of pre-lube on bearing faces but make sure the inside of the rods and caps as well as the backside of the bearing shells are absolutely clean and dry.

Posted on Oct 12, 2010

  • 6982 Answers

SOURCE: just need to know the

Running, pressure should be about 31psi....running with regulator vacuum line detached should be around 39psi A large difference indicates a problem, a small variance (one or two psi) may just be an inaccuracy in your gauge. No change when disconnecting vacuum indicates a bad regulator.

Posted on Feb 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

93 park ave.irs stuttering and it dies when u put it in drive


Could be anything from stuck on Tcc solenoid to a faulty fuel pump. May have enough fuel pressue to start but not run under load. TCC is in transmission and controls converter lockup if it happens at a stop it will shut the car off. My bet would be on the fuel pump. Check the fuel pressure and volume spec in a chilton book and install a fuel pressure guage to insure that it us at spec. Fuel pressure guages can be bought at any chain autoparts store there is a shrader valve on fuel rail that it hooks up to. Be sure to take all saftey precautions when using this.

Mar 19, 2017 | Cars & Trucks

2 Answers

Car doesn't seem to get enough gas to engine


Have you done a tune lately on the car?
I would also suspect a fuel pump problem is you've done a tune up recently.

Jul 11, 2008 | 1994 Hyundai Excel

2 Answers

On a 2004 Jeep Wrangler 4.0 it take about 30 sec to start I put a fuel gauge and it takes a while for the fuel to reach 45 psi I have to cycle the key on n off about 4 times then it will start after i


is this a double post, i just posted a huge full answer
just a while ago, on gc.
for same pressure..
the pump check balls bad,or fuelpumpreg inside.
or the injectors leak
last poster too, said awhile, 1s, 1min, 1hr what is while>
spec. is 1/2 min leak down or longer.
so>? but keyon 4 times, is fail

unplug injectors, (elect) is pressure 49 +-5 psi? and holds.
now, bingo.
leak down fails now.
yes the filers are all in tank
yes, the injectors can leak

un connect fuel rail hose, to rail block it.
hold pressure now
yes, bad leaking injector
no,, pump assy bad. assembly, why takes bench tests.

Jan 20, 2015 | 2004 Jeep Wrangler

1 Answer

Jeep grand cherokee takes a long time to start. cranks but no ignition


have a fuel pressure test done on the fuel manifold to check for pump--regulator and filter problems.

Jan 11, 2014 | 1994 Jeep Grand Cherokee

1 Answer

Does a 2003 jeep have an inertia switch?


as always check all fuses first....fuse 12,19,and 24, for sure.
which engine,? there are many and a diesel.
each engine has unique EFI and specs....

did you scan the ECU? some engines has DTCs for pump pressure.
look there. using a scan tool.(any in usa work, newer)
my wild guess , car cranks but dont start?
just a clue here.?

looked at alldata.com and there are no cut out.s.
no inertial, rollover or oil pressure fuel cuts.

the PCM controls 1 fuel pump relay that powers the pump.
we check fuel pressure cranking, to see if it meets spec.
if not , work that,
if good, pressure, then we back up and check spark
fuel is last, not first test.

and if you had a real FSM it does tell you all permisses
for it to allow pump to run.
it cuts fuel for lost spark is one.
or unflood mode.

1: fuses good?
2: all dash lamps glow key on,including the CEL?
3: got spark cranking? if not there will be no fueling by design (logic)
4: if compression is good, the engine runs with test fuel for
say 3 seconds, so you check fuel pressure cranking
and get 0 PSI (the actual pressure, is very important in this diagnosis.
0 , 10psi, 60? ( can be pump, 12v power to pump or regulator bad.)

that is the order, and if you get to #4 we work that.








Dec 29, 2013 | 2003 Jeep Grand Cherokee

1 Answer

I have a 1996 jeep grand Cherokee Laredo. it began to stall at idle and now will not start


Check audibly the fuel pump. It will run for 3 seconds when ignition is turned on, but engine not started. If it makes noise, you could check for pressue at the fuel rail. There is normally a schrader valve you can press. Tske care, fuel under pressure will come out when pump is ok.
if ok, check for eventual fault codes with scanner.
could be crank sensor.

Nov 02, 2013 | 1996 Jeep Grand Cherokee

1 Answer

I have a 1994 wrangler.must crank starter multipul times for fuel to reach fuel rail on 2.4 or 2.5 4 cyl.Once finally starts will run great all day and start.Next day starts hard again.I replaced fuel


replace the fuel pump,the check valve that holds pressure on the fuel is in the fuel pump.The fuel in the lines is draining back into the tank

Dec 10, 2017 | 1994 Jeep Wrangler

1 Answer

I need Fuel presure specs on a 94 Disco 3.9


2.39-2.672 kgf/cm2 .
pressue drop maximum 0.7kgf/cm2

Mar 14, 2010 | 1994 Land Rover Discovery

1 Answer

What should the fuel pressure be for a 2003 jeep wrangler


1. Connect fuel pressue gauge, start engine
2. Observe test gauge. Normal operating pressure should be 339kPa+/- 34 kPa (49.2 psi +/- 5 psi
3. Turn vehicle off.
4. Pressure should not fall below 30 psi for 5 minutes

i have these directions plus more about if want in pdf format, need email address to send if want

Feb 04, 2010 | 2003 Jeep Wrangler

2 Answers

1999 honda 4 cyl non v tech starts and dies does not idle just starts and dies until i try to start it like ten times then it will start and idle fine


Sounds like fuel problem.Check fuel pressue,make sure pressure is up to specs.If not,change fuel filter and fuel pressure regulator may be bad.

Sep 13, 2009 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...