Question about Cars & Trucks

Open Question

I'm driving a Hyundai Avante 2007. I'm facing 2 problems recently. The first one was there is a noise once I let go of the acceleration pedal. It will gradually stop once I step onto the brake pedal. The second problem was the vibration when I step onto the acceleration pedal once I hit the 80/90 km/h. I've changed both side wheel shaft and the centre bearing. Both problems still persists. Any help?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

fischmilch
  • 96 Answers

SOURCE: Honda Accord 2003 - Engine and steering vibration

You might to have a tire shop check the wheel for roundness, not balance. A tire can be balanced and be out of round, causing the shaking you describe. On front wheel drive cars, the wheel/hub assembly may be bad, which a good tire shop can tell you if it is. Can't say if it will be expensive, the hub is relatively inexpensive. Labor will probably be the deal-breaker.

Posted on Nov 07, 2008

csmock132
  • 4669 Answers

SOURCE: abs noise in 2001 Audi A6 2.7 T Quattro

It is common that ABS system do this from too much air gap to a wheel speed sensor. I would check the left front, since that is the side you had apart. Make sure the air gap is o.k and the reluctor wheel is the same size as the old one.

Posted on Mar 28, 2009

Monster80
  • 460 Answers

SOURCE: Vibration at speeds of 45-55mph

Check your drive shaft u-joints..Number one cause.Have a great night!!!

Posted on Apr 03, 2009

  • 79 Answers

SOURCE: Vibration and noise from front end while driving

Jack up the front end and put stands under it and block rear wheels. Look at axle boots and see if they are cracked. Try turning wheel back and forth sharply and see if you can hear any clicking. Problem could be outer axle joints. If the boots are cracked or you hear a clicking noise you will have to replace the axle. The axle and boot come as a complete unit. Please let me know what you find out.

Posted on Apr 15, 2009

billshoff
  • 23 Answers

SOURCE: On my 2005 subaru legacy outback 2.5l replaced

If I understand you correctly, you feel a vibration it the brake pedal when you apply the brakes. Is that correct?
Have your brake rotors re surfaced; they are warped.

"engine makes cavitating noise" ....what does this mean?

Posted on May 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car will not accelerate


Further information will be required unless you would nlike a simple solution like.
Step one start said vehichle
Step 2 apply foot ti brake pedal and put gear selector in drive
Step 3 remove foot from brake pedal to accelerator pedal
Step 4 apply presure to accelerator pedal untill desired speed has been acheived
Note these steps will not work for manual transmission see section 37

For braking see section 22

Oct 13, 2013 | Hyundai Cars & Trucks

1 Answer

Renault Kangoo 1900 diesel van squeeling over 26 mph but ok if i hold the same speed.


suspected clutch throw out bearing
failing
pressing on the clutch pedal loads up the bearing and the noise stops but removing the foot from the peddle allows the the pressure plate fingers to spin a loose bearing race ans so makes the noise

Mar 16, 2017 | Cars & Trucks

1 Answer

When slowing down high pitch noise Hyundai i30 2011


your drivetrain is screaming already. Hope for the best.

Jul 20, 2012 | 2011 Hyundai i30 1.6

1 Answer

1992 corolla won't accelerate


the auto-transmission control linked to accelerator pedal might have changed its position.loosen the screw on the sliding lever,start the engine ,slowly slide the lever and once it started engaging set t/m about 900rpm.

Feb 27, 2012 | 2007 Toyota Corolla

1 Answer

I have an s80 2007 d5 diesel volvo. the


I took the car to volvo garage in the morning . They found out that there was a cut cable in the engine compartment near the throttle valve.
Anyway i want to express my thanks to you for your immediate response.

Regards
George

Feb 08, 2010 | 2007 Volvo S80 V8 Sedan

2 Answers

Gas pedal reving up and not relaxing.


I have had a problem on a 2008 Santa Fe with the gas pedal going to idle while driving. I shut the car off and turned it back on and it behaved normally so I drove it to the dealer. It had triggered the check engine light and the Hyundai mechanics were able to read a code that told them that the problem was in the sensor on the pedal. They replaced it under warranty. No problem since.

Jan 29, 2010 | 2007 Hyundai Santa Fe Limited

1 Answer

2007 Hyundai Sonata


the car is front wheel drive so you may have a brake problem. maybe a loose brake caliper or pads.

Aug 09, 2008 | 2007 Hyundai Sonata Limited Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...