Question about Dodge Ram 1500

Open Question

How to change crankshaft sensor on 2002 dodge 5.9 engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 30 Answers

SOURCE: 04 Dodge SRT 4 crankshaft sensor

The Crankshaft Position Sensor is located directly next to the starter.

  1. On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
  2. Remove the Structural Collar
  3. Unlock and disconnect the electrical connector to the crankshaft position sensor.
  4. Remove the crankshaft position sensor bolt.
  5. Remove the sensor
Reverse Order to install except note that:

Use a twisting motion when installing the sensor.

Install and tighten the crankshaft position sensor bolt and tighten to 9 N·m (80 ±15 in. lbs.).

Posted on Aug 16, 2008

Ad

SOURCE: 2005 dodge crankshaft sensor

buy a new car or try the camshaft position sensor

Posted on Nov 08, 2008

  • 14036 Answers

SOURCE: 1997 Dodge Ram 1500 5.9 gas v8 engine. Lost Fire,

you have pcm problems or ASD relay problems.they both control the fuel and ignition.

Posted on Jun 05, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

  • 396 Answers

SOURCE: 2002 dodge stratus crankshaft sensor location?

The crankshaft or the shankcraft as we refer to it is inside the engine, it turns over the pistons. Never heard of such an animal. You may have a fuel pump going out, clogged fuel filter, fuel injectors, Idle air control valve going out, bad plugs, plug wires or distributors. Just began checking them one at a time.

Posted on Jun 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 dodge grand caravan 3.8 engine wont start


If you drove it to the dealer, the crankshaft sensor was not bad... Find another repair shop.

Aug 12, 2012 | 2002 Dodge Grand Caravan

1 Answer

Where is the crankshaft position sensor located its a 2002 dodge neon


The crankshaft position sensor is located between the alternator and the oil filter. You can identify this small component by the electrical connector attached to it and the single bolt that secures it to the engine block.

Mar 07, 2011 | Dodge Neon Cars & Trucks

1 Answer

Jsut want to know where crankshaft position sensor


Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

0996b43f80202990.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

0996b43f8020299e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below

Apr 15, 2010 | 2002 Ford Escape

2 Answers

1)How difficult is it to change crank case position senor for 2002 Olds Aurora 4.0 engine? Eng check lite on for that reason. 2) Losing oil only when engine running. Can smell in passenger compartment when...


2002 Oldsmobile Aurora V8-4.0 Replace Crankshaft (Sensors) A and B This car has 2 sensors 1- Raise and support car. 2- Remove the oil filter adaptor. 3- Remove crankshaft sensor electrical connector. For specific CKP sensor identification. 4- Remove the crankshaft sensor retaining bolt. 5-Remove the crankshaft sensor. NOTE= Inspect the CS sensor o-ring for wear or damage, if problem is found replace it also. 6- Lube O-ring with clean engine oil. 7- Install theretaining bolt TIGHTEN to 10 N.m (89lb in) 8-Install the CS sensor electrical connecror. 9- Install oil filtor adaptor. 10- Lower car. 11- Operate engine and inspect Cs sensor for oil leaks 12Perform the CKP system variation learn procedure.

Feb 10, 2010 | 2002 Oldsmobile Aurora

1 Answer

2002 dodge stratus crankshaft sensor location?


The crankshaft or the shankcraft as we refer to it is inside the engine, it turns over the pistons. Never heard of such an animal. You may have a fuel pump going out, clogged fuel filter, fuel injectors, Idle air control valve going out, bad plugs, plug wires or distributors. Just began checking them one at a time.

Jun 30, 2009 | 2002 Dodge Stratus

1 Answer

Engine stalls in drive after check engine light came on.


Have it sacnned for a code. it seems to be the speed sensor at the tranny.or the crankshaft position sensor. hope this helps. will you please vote ?

Dec 19, 2008 | 2007 Dodge Ram 1500 Quad Cab Sport

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...