Question about 1985 Ford Bronco II

Open Question

I have a stuck door lock on my 85 Bronco II XLT. Won't manually or electronically lock.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: door actuator 1991 bronco( passenger side)

you need to  take off the inside panel. if i remember correctly its just a couple screws and it should pop off.

Posted on Jan 12, 2009

Ad
  • 69 Answers

SOURCE: lifter ticking ,clean oil, good oil pressure ,runs

sounds like a wornout push rod....if it ticks fast as you hit the gas ,then i beleive its the rod.

Posted on Jul 21, 2010

  • 161 Answers

SOURCE: My 1989 Bronco II driver

The gears are either misaligned or stripped. I really doubt they ate stripped. Getting the door panel off is a pain, but you will figure it out. I'm not talking about your model specifically, but typically you will have to remove 2 to 3 screws in the arm rest. And one screw in the hollow under the door handle. After that, the door should only be held on by christmass tree fasteners. Which are just plastic cone shaped fasteners that snap into a hole in the sheet metal. Try to be as close to the fasteners as possible while popping them out, so you don't tear them off the door skin. There is a tool made for this that I am sure you could borrow from autozone. It's a trim removal tool. The large gear that pushes your window up is most likely just out of place. Be careful. And make sure the battery is disconnected before you put your fingers in harms way.

Posted on May 07, 2011

  • 142 Answers

SOURCE: I have replaced fuse 63 an all doors now lock and

Probably rusted and needs to be freed up.

Posted on May 27, 2011

  • 68 Answers

SOURCE: My back doors on my

IF CENTRAL LOCKING REMOVE THE DOORPANELS. 2 WIRE WILL B5E CONNCTED WITH A CONECTOR BLOCK. NORMALLY BRASS. AJUST THEM TILL THE DOORS LOCK.

Posted on Jun 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bronco 2 won't keep running unless you hold the key


Very possible.
You could disconnect the rod between the lock cylinder and the switch to see if the lock is the problem. The switch is on the bottom of the steering column.

Apr 12, 2013 | 1988 Ford Bronco II

1 Answer

Bronco II won't start


86 ford bronco 2 won't start changed coil wire acts like it wants to start not getting spark

Nov 10, 2012 | 1988 Ford Bronco II

1 Answer

I have an 85 bronco 2 and the pedal is hard as a rock. All of the breaks are free! Could this be a booster?


Yes, your booster could be stuck therefore causing the pedal to be unable to move. Replace it.

Aug 27, 2011 | 1985 Ford Bronco II

1 Answer

1989 ford bronco II xlt running absolutely fine parked vechicle for an hour now it will not start but appears to want to turn over but won't


hard starting on hot engines is caused by just 2 things:

1. carbons in starter needs to be replaced.
2. ignition timing is overly advanced. timing should be recalibrated by your mechanic.

Aug 05, 2011 | 1989 Ford Bronco

1 Answer

How to get the right fuel pump relay for 1988 ford bronco 2 xlt can't see numbers on it. 4 wheel drive manual trans. 2.9 v/6 engine


Call the parts stores.

Call more than one to check prices.

Don't let them try to rip you off.

Nov 07, 2010 | 1988 Ford Bronco II

1 Answer

Lifter ticking ,clean oil, good oil pressure ,runs smooth , but ticks like a machine gun ?1990 bronco ii 80,000 miles 2.9L xlt 4x4


sounds like a wornout push rod....if it ticks fast as you hit the gas ,then i beleive its the rod.

Jul 21, 2010 | 1990 Ford Bronco II

1 Answer

What years will 1990 bronco 11 engine and driveline work ?


85-91 bronco II or ranger 2.9 cid
front drive shaft 85-90
rear drive shaft 89-90

Mar 29, 2010 | 1990 Ford Bronco II

1 Answer

Hello, I purchased a 1996 ford bronco xlt saturday. It has a viper alarm system & an ignition key only(does not fit the doors). It will lock you out of the vehicle & I have no other way to access...


you should be still able to use the vin to cut a new key at Ford,a locksmith is about $100.00----if not a complete lock set(2 doors,ignition and not sure about tail gate is about $75.00

Feb 16, 2010 | 1996 Ford Bronco

1 Answer

I have a 1987 Bronco 2 xlt and today when i pressed the 4x4 button it just wouldnt light up and wouldnt make the clicking sounds like it was engaging any ideas?


well after putting the bronco into a heated garage for about 30 minutes it seemed to go right into 4x4 so my guess is it was just froze up

Jan 07, 2010 | 1988 Ford Bronco II

1 Answer

Electric windows and door lock will only work when the drivers door is all the way open1989 Bronco II


The wire harness has a plug in in between the door and the car,the the plug is about to come loose,it runs threw a boot into the left kick panel.

Nov 04, 2009 | 1989 Ford Bronco II

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...