Question about 1990 Ford F150

Open Question

1991 F-150 Torque specs axle nut - 1990 Ford F150

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: torque specs 7.5 inch rear axle 96 ford ranger

Differential bearing caps 70-85 ft lb
Ring gear bolts 70-85 ft lb
Pinion bearing preload if using original bearings 8-14 lb-in, if installing new bearings 16-28 lb-in

Posted on Jan 30, 2009

warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

tneubauer
  • 437 Answers

SOURCE: Torque Specifications

1. If you are speaking of the large yoke nut there is no "torque spec" per say, instead it is a rotational preload-

From Ford manual:
Use the special tool to hold the pinion flange while tightening the nut to set the preload.

  • Tighten the nut, rotating the pinion occasionally to ensure the differential pinion bearings are seating correctly. Take frequent differential pinion bearing preload readings by rotating the pinion with a Nm (inch-pound) torque wrench. The final reading must be 0.56 Nm (5 lb-in) more than the initial reading taken during removal.
2. If you are looking for the yoke straps that hold the universal in place to the yoke it is 14ft lb for the 4 bolts.

Posted on Jun 01, 2009

emissionwiz
  • 75108 Answers

SOURCE: spindle nut torque spec on a 2004 F-150

u DON'T torque this!! tighten the nut while spinng the rotor, then back off untiol it is free, then tighten it down until it seats tight, then turn another 1/8" tighter, that is it, any tighter u burn up the the wheel bearings

Posted on Feb 04, 2010

Zeevert
  • 373 Answers

SOURCE: axle nut torque specs 2004 escape

Front axle nut torque is 300Nm or about 220 ft-lbs.

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for axle nut


there is no torque specification. rule of thumb, tighten the nut til firmly tight, back off a half a turn.

Jul 31, 2014 | 2006 Pontiac Torrent

1 Answer

Front hub torque specs


The torque for the hub bolts is 120 ft. lbs
The torque for the axle nut is 185 ft. lbs.

Dec 29, 2013 | Dodge Cars & Trucks

1 Answer

What is the torque spec for the front center axle nut on a 2003 tahoe?


The torque specs.are for 15k series trucks is 155 ft.lbs.For 25/35 series it`s 133 ft.lbs.Hope this helps.Good luck.

Dec 03, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

97 F250 HD Rearend axle bearing retaining nut Torque Spec for used bearings. It is 10.25 sterling rear gear w/ 7.3L diesel eng.


Axle retaining nut torque spec is 55 to 60ft lbs. back off 5(new) or back off 8(used) clicks, and axle retaining bolts 60-80ft lbs in criss cross pattern.

Apr 25, 2011 | Ford F-250 Cars & Trucks

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

2 Answers

1995 Millenia S CV axle nut torque?


174-231 ft lbs. I would stay closer to 174.

Jan 27, 2010 | 1998 Mazda Millenia

1 Answer

Torque specs on replacing cv axle on 05 Pacifica


ok here we go tie rod=55 ft lbs axel nut= 180 ft lbs strut bolts= 65 ft lbs plus 90 degrees

Jan 07, 2010 | 2005 Chrysler Pacifica

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
1990 Ford F150 Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5471 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...