Question about 1993 Isuzu Rodeo

Open Question

Intake manifold 93 isuzu rodeo - 1993 Isuzu Rodeo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: engine light was on and engine idles rough.

these O2 sensors are cat convertor check sensors. id be checking cat convertors and hopefully you should try replacing if not all ready is the front bank 2, O2 sensor
if you have scanner can you see fuel trims in data display to confirm high fuel trim only on bank 2 either +-5 or more indicates problem and if bank 2 sensor 2 has fixed high 700mv reading cat no good(warm idling)

Posted on Jul 10, 2009

Ad
  • 484 Answers

SOURCE: 93 isuzu rodeo wont go in gear its a 5speed, there

Follow the line from the clutch master cylinder to the transmission and look at the slave cylinder. Do you see a leak anywhere? Pull back the boot on the slave if you have to. If there is a leak (and there should be because you do not just lose fluid from the clutch hydraulics) you will need to replace the faulty component and bleed the system. To bleed the system, get a glass jar, tubing that fits securely on the bleeder valve and the appropriately-sized wrench. After you replace the leaking part, open the clutch master cylinder's reservoir and fill it with brake fluid. Put the box (closed) end of the wrench on the bleeder valve and then put the tubing on and run it into the jar. The shorter the length of this line, the better. Pour enough brake fluid into the jar to submerge the end of the line. Now have someone help you in the car by pumping the clutch pedal. Open the bleeder valve and watch for the brake fluid to start coming out. When it does, close the valve. Have the person operating the clutch pump the pedal a few times and then hold it down. Open the valve and let the fluid run out, then close the valve. Repeat this procedure until no air comes out anymore.

i hope this helps out,
matthew

Posted on Oct 25, 2009

Testimonial: "thank you"

c17hydro
  • 2984 Answers

SOURCE: replacing a new starter on a 93 isuzu rodeo

Don't know what size motor you have because you didn't post it so please pick the proper one:

This is for the 4 cylinder motor--

8e64f3e.gif
4-cylinder engine starter connections



  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. If equipped, it may be necessary to disconnect and remove the EGR pipe to access all the starter bolts.
  4. Tag and disconnect the starter battery and control wiring at the starter.
  5. If equipped, remove the starter bracket and/or heat shield.
  6. Remove the starter-to-engine bolts.
  7. Move the starter away from the engine and down to remove from the vehicle. Some starter may be installed with shims between the starter and engine. When the starter is removed, these shims may fall out. Do not loose them.
To install:
  1. Install the starter and shims, if equipped to the engine. Align the mounting bolt holes and insert the bolts. Hand-tighten the bolts.
  2. Tighten the starter mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  3. Install the starter bracket and/or heat shield, if equipped.
  4. Connect the battery and starter control electrical wires to the starter.
  5. If the EGR pipe was removed, install it.
  6. Lower the vehicle.
  7. Connect the negative battery cable.
  8. Start the vehicle to make sure the starter functions correctly.
This is for the V6 motor--

8fdc27b.gif
6-cylinder engine starter installation


  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle on jackstands.
  3. Label and disconnect the battery and starter control wires from the starter.
  4. If equipped, remove the starter bracket and/or heat shield.
  5. Remove the starter-to-engine mounting bolts.
  6. Lower the starter from the engine. If any shims are present, keep them for reinstallation purposes.
To install:
  1. Install the starter and shims, if equipped, to the engine. Tighten the mounting bolts to 30–34 ft. lbs. (39–44 Nm).
  2. Install the starter bracket and/or heat shield, if equipped.
  3. Reconnect the electrical connectors to the starter.
  4. Lower the vehicle.
  5. Connect the negative battery cable.
  6. Start the vehicle to make sure the starter functions correctly.

Posted on Nov 19, 2009

kel1guy2002
  • 3740 Answers

SOURCE: How to clean EGR valve passages in 1993 Isuzu Trooper DOHC V6

You have to the EGR valve (sometimes the Intake manifold to EGR Vlalve line also). After you remove it take a drill bit the about 20 % smaller than the actual hole of the outlet side and rotate the drill bit with your hand to dig out the carbon. Aditionally the line coming from the intake manifold to the EGR valve will clog near the connection to the EGR valve. I use either a single piece of copper wire or the wire that you would use to tie ribar together to clean the line. When your done cleaning take a piece of vacuum line and connect it to the diaphram side and **** on it... then plug the line well with your thumb. Grasp the valve and blow thru it... Air should blow thru it freely. Remove your thumb from the vacuum line and try blowing again.. No air should pass thru the valve.
Then reinstall the valve and start the vehicle with the vacuum line disconnected (but blocked off) Use another piece of vacuum line connected to the diaphram again and **** on the line.. The vehicle should die or run really bad. If it does this then you cleaned it correctly.

Posted on Jan 20, 2010

  • 617 Answers

SOURCE: timing belt replacement on 93 isuzu rodeo

what need to know? 2wd or 4wd and what motor, if need diagram need email address to send to

Posted on Feb 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for 99 Isuzu rodeo intake manifold


18 ft lbs. Start in center, work side to side toward the ends. Recheck twice with same pattern.

May 23, 2014 | 1999 Isuzu Rodeo

1 Answer

Where is 98 rodeo 3.2l v6 idle air intake sensor


The intake air temp is located in ducting hose or intake manifold assy..

Sep 20, 2013 | 1998 Isuzu Rodeo

1 Answer

Bad theromostat 3.2 isuzu how to


The thermostat on the 2001 Isuzu Rodeo 3.2L v6 is located on the top of the engine under the upper intake manifold. In order to replace it you will have to depressurize the fuel system by running the engine with the fuel pump fuze removed until the engine dies and then carefully remove the fuel rail and injectors. Then remove the intake manifold which will give you access to the coolant nozzle fixture attached to the top of the engine. The thermostat is in the top of the engine block under the nozzle fixture. Be sure to replace the thermostat with the proper replacement part (may be difficult to find) and put on new gaskets for the intake manifold before replacing it.

Apr 11, 2013 | 2001 Isuzu Rodeo

2 Answers

Where is the map sensor located on a 2004 isuzu rodeo 3.5l v6


check the right side of the intake manifold or the rear of the manifold

Mar 04, 2011 | 2004 Isuzu Rodeo

1 Answer

I have a 2001 isuzu rodeo ls. I was told that i need to replace the manifold gaskets. My husband did the top of the manifold gaskets. and it is still idling up and down. Is it easy to replace the...


This would be the intake manifold gasket that needs replaced if the diagnosed correctly. It is on the top of the engine. If your husband properly replaced the intake manifold gasket and you still have the problem then the diagnosis was wrong and something else is the problem.

Jan 08, 2011 | 2001 Isuzu Rodeo

1 Answer

Where is the nock senseser?? On a 99 Isuzu rodeo V6


If it is a v6 then they should be in the valley between to two heads and under the intake manifold. if it is a four cyl. check high on the block on the intake side.

Aug 19, 2010 | 1999 Isuzu Rodeo

1 Answer

Need torque specs for isuzu rodeo 3.2 intake manifold


josephrloop,

Go to: http://www.autozone.com/autozone/ymme/ymmeYear.jsp?_requestid=552857

Here you can select the year, make and model.

I hope this information proves useful and helps you with your intake torque success.

Cordially,

carsandcomps
Guru @ Fixya

Apr 10, 2010 | 2000 Isuzu Rodeo

Not finding what you are looking for?
1993 Isuzu Rodeo Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...