Question about 2008 Pontiac Grand Prix GXP

Open Question

2008 GXP front turn signal bulb replace

I need to replace the front turn signal bulb

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 401 Answers

SOURCE: need to replace the right front turn signal bulb

remove the 2 screws remove the light and replace the bulb

Posted on Nov 05, 2009

  • 57 Answers

SOURCE: 2004 Pontiac Grand Prix GTP front pass turn signal doesn't work

you would need to buy a blinker relay

Posted on Jul 11, 2010

  • 1 Answer

SOURCE: replace front right turn signal bulb

I replaced the front right turn signal on my 2005 Pontiac Montana by reaching up from underneath. I tried removing the battery but the opening from above was too small. I was able to pull the ground effects open enough to get my arm in. When you reach the bulb holder feel for two wings on the bulb socket and give the whole socket a quarter turn to and it will release. The wires are long enough so the entire bulb holder will drop down below the vehicle so you can easily replace the bulb.
Reverse the step to put it back in. You will not be able to see what you are doing so I had someone guide me by watching from above. Took less than 10 minutes once I decided to change the bulb from the bottom. I did not need to jack the vehicle up or use ramps.

Posted on Jun 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace a front turn signal bulb in a 2007 kia optima


Greg, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Front Turn Signal Change Kia Optima 2006 2010 2008 Kia Optima EX 2 4L 4 Cyl

Mar 27, 2016 | Kia Cars & Trucks

1 Answer

How do i replace right front turn signal bulb on 2008 cadillac dts


My automotive database says you have to remove headlamp assembly to replace bulb. To remove headlamp assembly, you need to remove front bumper fascia.
Why in the world should you have to remove front of vehicle just to change a bulb, I don't know? My database is the only info I have to go by. I doubt I can walk you through it, step by step, I can't see anything from here.

Mar 01, 2016 | 2008 Cadillac Dts

1 Answer

Where is the turn signal relay located. Changed bulb and it still doesn't blink


seems like it is in the fuse block under dash . or we would bot hear it clicking

Sep 07, 2015 | 2008 Pontiac Solstice GXP

1 Answer

How to change front turn signal bulb on 2008 SRX Cadillac


Nope don't need to drop the whole light assembly. I just took the wheel and inner cover off, then the 6 torx screws that hold the light hosing together , replaced the turn signal bulb and good to go!!

Mar 04, 2013 | 2004 Cadillac SRX

1 Answer

Change turn signal bulb 2008 srx


Front turn signal bulb replacement 2008 SRX . Jack up car & block . Remove front wheel & front half of the wheel house assemble. There are about 7 plastic pull rivets that have to be removed . Pull out the wheel house . Remove turn signal & driving light cover held on by 6 # T10 torx screws . Twist out socket & replace bulb # 3757NAK . Should take about 45 min.

Mar 26, 2012 | 2006 Cadillac SRX

2 Answers

My 2008 Chevy Cobalt coupe has a passenger side turn signal that flashes fast on the instrument panel. However, no turn bulb is burnt out in either the front or rear. The rear passenger turn blub just...


It is as simple as your hazzard switch needs to be replaced yes your hazzard switch as now turn signals are built threw the hazzard switch my PT Cruiser had same problem as my s10 replaced hazzard switch fixed the problem

Aug 18, 2011 | 2008 Chevrolet Cobalt

1 Answer

2008 Chevy Cobalt front right turn signal is not working. Back right signal blinks fast. Left signals work just fine. I tried replacing the bulb and it did not work. Do I need to replace the...


No - headlight ok.
The reason that the Right turn signal blinks fast is that there is half the normal load (resistance)
on the right side, since the Right front turn signal isn't working.
Since you replaced the Right front turn signal bulb, your problem lies in the bulb socket or
the wiring to the socket.
(1) try cleaning out the socket - there's probably a contact problem in the socket. You
may need to squeeze the contacts together to provide good contact to the socket contact.
(2) if contacts inside the socket are ok, try back-probing the socket - to make sure that the
socket is getting 12V DC to light the bulb. Replacing a bulb socket is easy, and commonly done.
Any auto parts dtore should be able to sell you a new socket - its just a matter of cutting out the
old one, and then splicing in the new one. Most shops will use small wire nuts, buried under several
wraps of E-tape (electrical tape).
(3) if bulb AND socket ok, you have the worst problem known to man - a wiring fault. In this case,
you'll want to run a new wire from the flasher module (under the dashboard) to the turn signal.

Jul 29, 2011 | 2008 Chevrolet Cobalt

1 Answer

How do i replace the front turn signal bulb on my 2008 chevy uplander it looks like I need to remove the front lamp assembly first. I got two of the connections off ( the bolt on top and the locking pin...


To get at the turn signal bulb, you gain access to it by first removing the headlamp housing which is directly above it. Remove the top bolt and locking pin (as you mentioned), then remove the headlamp housing by pulling it (or pushing it from behind) straight forward to release the friction pressure clip located near the outside edge of the housing. To prevent damaging the headlamp housing's rubber gasket, you may have to first release several of the plastic grille's black plastic clips nearest that housing by pulling upward on the clip heads and removing them; they are re-useable. It's simple and quick to do once you've figured it out. I carry spare bulbs...beats getting a ticket.

Feb 16, 2010 | 2008 Chevrolet Uplander

2 Answers

Need replace turn signal bulb


YOU HAVE TO THE FRONT HEADLIGHT HOUSING TO REPLACE THE TURN SIGNAL BULB.

Aug 24, 2009 | 1996 Chevrolet Cavalier

1 Answer

2008 Camry Front Turn signal Bulb


Front Open The Hood And View Back Of Headlight Turn And Then Pull Light.
Rear Open Trunk And Remove Carpet From Behind Light Now You Can View The Bulb Housing Turn And Pull.

Nov 16, 2008 | 2008 Toyota Camry

Not finding what you are looking for?
2008 Pontiac Grand Prix GXP Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...