Question about Toyota Land Cruiser

Open Question

Toytoa landcruiser bonnet catch will not close

D4D model spring popped out from front bonnet dont kno where it goes...bonnet wont close

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

raycrazek
  • 106 Answers

SOURCE: landcruiser auto transmission,,how to check fluid level

when you open your hood look in the back of the motor on the left side.. you should see a stick with a circle on the end of it for your finger have you vehicle running warmed up that means let it run for 10 or 15 min. and then pull the stick out.. wipe it off real good. stick it back in all the way.. pull it back out and hold it horizontally and check it.. it's sometimes hard to read because it has bubbles on it.. try it a couple of times to get an accurate reading good-luck ray

Posted on Jan 16, 2009

  • 2 Answers

SOURCE: renault clio bonnet wont open

Get a second person to pull bonnet catch and you push up and down on the bonnet whilst catch is being pulled. 1, cable possibly stretched, 2, look at bonnet catch under the coloum to see if wire is attached, 3, try and lie under car and look up the back of the bulkhead to see the catch and release it manually. Hope that helps.

Posted on Aug 17, 2009

gordanddar
  • 477 Answers

SOURCE: The pass. side bonnet catch will not release and open the bonnet.

Have someone lift on the bonnet while you pull the release handle.

Posted on Nov 06, 2009

  • 70 Answers

SOURCE: front hood wont lock closed

you have a problem with your primary hood latch, your secondary latch keeps it from flying up into your windshield. inspect the pri. latch, it may have stuck and won't close. a thorough soaking with a good penetrating oil usually frees it up. if not you may have to replace the latch.

Posted on Dec 19, 2009

  • 1 Answer

SOURCE: ford focus 56year key wont open bonnet stripped

I also have the same problem with a 2007 ford focus. I have been informed that it is a common problem and that the barrel needs to be changed. I believe it is necessary to open the bonnet by trying to remove the panel/ covers from under the front bumper. I managed to get the panel off by removing about 8 screws but I was still unable to open the bonnet.
If you have any luck, would you please respond.

Posted on Jan 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Audi 2002 bonnet will not open. Bonnet pops when interior handle is pulled but will not open fully when pulling catch on front of car !!!!!


Sounds like you have a cable problem take it to a garage.These are very tricky to replace and expensive.

Feb 27, 2015 | 2002 Audi A4

1 Answer

Front bonnet catch wont release fully,i pull lever from inside and it releases bonnet just a couple inch, then when try to lift bonnet up it wont open. regards mike, and thanks in advance


There is another lever at the front of the car that you need to release too. This is to prevent the hood flying open if you accidentally pull the release while driving. After you release the latch inside the car, go to the front of the car, near the Audi rings in the center of the grill there is a small black tab that pops out. Pull up on it and the hood will open. Let us know if that worked.

Oct 23, 2013 | 2002 Audi A4

2 Answers

Hi, I have a 1995 Audi coupe, the bonnet is stuck on one side so when I pull the bonnet release the bonnet only pops up on one side. any ideas? thanks


get somone to push down on the bonnet and pull it up while u pull the relise handle. if dont work then strip the front grill and u should be able to open the catch manualy

Jul 10, 2013 | Cars & Trucks

2 Answers

2003 Landcruiser wont select Drive


This is a electronically controlled gearbox, so the first thing that must be done is to have the Transmission control module scanned for faults codes.

Jun 13, 2012 | 2003 Toyota Land Cruiser

1 Answer

I cannot open the bonnet of my car


I think the spring which pops the bonnet is too weak for its weight.
I keep a small pice of wood in the car which I put under the release lever. This holds the catch open while I go round to the front, lift the bonnet and release the safety catch.
Try it!

Feb 17, 2011 | 2000 Alfa Romeo 156

1 Answer

Opened my hood to give a buddy a boost now it wont close for me any tips


No good deed goes unpunished. It sounds like the secondary safety catch is bent and not going into it's opening. Look at where the pointy catches enter the front frame of the car and make sure they line up as you close the hood. If they do line up, it's possible that the catch that springs against the hood pin is frozen or stuck. Spray some penetrating oil into the latch mechanisms at the front frame of the car and also try pushing the release lever inside the car back into the closed position. Sometimes they get stuck in the open position.

Dec 14, 2010 | Ford Explorer Cars & Trucks

1 Answer

Where is the bonnet release catch on a ford focus


Go to the ford badge at the front of the car
Swivel the badge (its spring loaded)
Insert your ignition key and turn to the left (position 1)
The bonnet should pop up
Turn the key to the right (position 2)
You can now lift the bonnet.

Sep 20, 2010 | 2002 Ford SVT Focus

1 Answer

The pass. side bonnet catch will not release and open the bonnet.


Have someone lift on the bonnet while you pull the release handle.

Nov 06, 2009 | 1997 Mercedes-Benz E-Class

2 Answers

My bonnet on my BMW e36 wont close fully so it is flush to the wings like it is suppose to, is there anyway i can adjust the bonnet to make it be fully closed and flush to the rest of the car many thanks...


My bonet on my 1 series wont close properly it doesnt appear to be catching in the release lock although the mechanisim is working when I press down on it manually. The bonnet is only staying shut because the opener catch/hook is working, but this is the only thing holding it closed.

Sep 12, 2009 | 1997 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...