Question about 2001 Volvo V40

Open Question

V40 tailgate panel removal - 2001 Volvo V40

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Renault kolos rearlower tailgate stack


Most likely cause would be a defective motor or the wiring to it. Remove the trim panel off the tailgate and check the motor for 12 volts when you operate the tailgate.

Apr 04, 2016 | Renault Cars & Trucks

1 Answer

How to open the tailgate if handle or cable is broken on 2003 sequoia


I had the same problem with my 02 Sequoia. To get the tailgate open and replace the broken handle you will have to remove the tailgate's panel cover.

The panel is affixed to the tailgate with about six to eight plastic stays on the back side of the panel.

You will need a "L"-shaped tool (The tool looks like a screw driver with its tip bent one-to-two inches.) that can be inserted under the panel's edge. Start @ the right, or left bottom corner.

After you pull the panel's second plastic stay away from the tailgate you will be able to use your hand to pull the rest of the stays away from the tailgate then push up on the panel to remove it.

After the panel is removed you will be able to see where the cable feeds into the broken handle. Use a pair of needle-nose pliers to pull the cable and open the tailgate. Toyota charges $100.00 for a new handle.

Hope this helps and is not to confusing.

Oct 09, 2011 | 2002 Toyota Sequoia

2 Answers

Rear hatch on my 2001 explorer will not open, rear window will but tailgate hatch will not. how do i open it with out the unlock button, no manual release that i can see...


I had a clip break when I tried to open my tailgate. I had to remove my inside hatch panel and find my way to the handle assembly. A little plastic clip (shaped like a T) had finally worn out, which wouldn't hold the locking arms, and I had to go to a Ford dealership for a $3 part; tailgate has worked fine since then!

Sep 01, 2011 | 2001 Ford Explorer Sport

1 Answer

02 liberty rear wiper dose not work plugin has power changed wiper motor still doses work


There is a nut under the black plastic bezel that needs to be removed. Here is the complete procedure for you to look at. Its possible that your arm isn't adjust at wiper motor...

REMOVAL
- Disconnect and isolate the battery negative cable.
- Remove the rear wiper arm from the rear wiper motor output shaft. (Refer to 8 - ELECTRICAL / REAR WIPERS / WASHERS/REAR WIPER ARM - REMOVAL).
- Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL). Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
- Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel (REAR WIPER MOTOR OUTPUT SHAFT NUT REMOVE/INSTALL).
- Remove the bezel and gasket from the rear wiper motor output shaft.
- Remove the trim panel from the tailgate inner panel. (Refer to 23 - BODY/SWING GATE/TRIM PANEL - REMOVAL).
- Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
- Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle (REAR WIPER MOTOR REMOVE/INSTALL).
- Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
- Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
- Remove the rear wiper motor and mounting bracket from the tailgate as a unit.

zjlimited_494.gif

1 - BEZEL AND GASKET
2 - OUTPUT SHAFT
3 - TAILGATE OUTER PANEL
4 - NUT
5 - NUT COVER

What you will need to do is to remove the small plastic cap on the wiper arm by prying it off with a screw driver. Then remove the nut that holds the arm onto the shaft. Then get yourself a battery cable puller (from auto parts store) and pull the arm off of the shaft..

zjlimited_495.gif

1 - SPARE TIRE
2 - WRENCH
3 - FLIP-UP GLASS
4 - PARK RAMP
5 - REAR WIPER ARM
6 - PIVOT COVER

Jul 19, 2011 | 2002 Jeep Liberty

1 Answer

HOW DO YOU REPLACE THE REAR WIPER MOTOR ON A 2003 JEEP LIBERTY?


REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the rear wiper arm from the rear wiper motor output shaft.
  3. Using a small thin-bladed tool, gently pry at the notch in the base of the rear wiper motor output shaft bezel to unsnap the nut cover from the bezel .Be certain to take proper precautions to protect the outer tailgate panel and its paint finish from damage during this procedure.
  4. Remove the nut that secures the rear wiper motor output shaft to the outer swing gate panel
  5. Remove the bezel and gasket from the rear wiper motor output shaft.
  6. Remove the trim panel from the tailgate inner panel.
  7. Disconnect the tailgate wire harness connector for the flip-up glass ajar switch from the flip-up glass latch connector receptacle.
  8. Disconnect the tailgate wire harness connector for the rear wiper motor from the motor connector receptacle
  9. Loosen the two screws that secure the rear wiper motor mounting bracket to the top of the tailgate inner panel.
  10. Slide the rear wiper motor and mounting bracket forward far enough to disengage the two mounting screws from the keyed slots in the top of the tailgate inner panel.
  11. Remove the rear wiper motor and mounting bracket from the tailgate as a unit.
To Install just reverse steps

Jan 23, 2011 | 2003 Jeep Liberty

1 Answer

Tailgate will not open; handle will not move


Either ,something is binding inside the tailgate, or broken.
You can get to the mechanism from the inside panel of the tailgate-- by
removing the screws that down the inside panel.
Once you remove the panel you should be able to open the tailgate by
pulling on the thin cable to unlatch the latches from both ends of the tailgate and a good look at the handle mechanism will tell you what wrong.
Good Luck.

Mar 20, 2010 | 1991 Nissan Pickup

1 Answer

I need to remove 2004 toyota sequoia tailgate door panel to get access the rear tail light to install a backup camera. I don't see any obvious removal points.


Slide the plastic cover off the tailgate ******** the passenger side to reveal a 10mm bolt.

Remove the bolt and the strap/

Using a flat prying instrument, remove the center trim section one the inside of the tailgate above the window.

Grab the top edges of the side trim sections on the inside of the tailgate and pull down to remove.

Using a flat instrument, pry at the bottom edge of the tailgate main trim panel, it is held on with about 12 plastic pop-in fasteners so it will take several 'pops' before it is released.

Behind that there is a metal access cover the width of the tailgate, held on by ~5x pop in fasteners and ~10x 10 mm bolts. Remove the bolts and pop the panel loose, it will hang by the wiring so support it while you do your camera work :)

The license plate trim panel, should you need to remove it, requires remoaval of the license plate.

Then remove ~3x 10mm bolts from the top of the panel, accessed from the inside.

Using long needle nose pliers compress the pop-fasteners holding the lower corners of the license plate trim panel on, being careful not to let it drop and slide down the vehicle, scratching the paint :)

Sep 20, 2009 | 2003 Toyota Sequoia

1 Answer

2002 Ford Ranger Exterior Tailgate Handle Broken


There should be an access panel on the bed side of the tail gate. If you have a liner installed on the tail gate you will need to remove it to gain access to the panel. Panel is probably held on with torx screws but you may get lucky and have regular bolts. just remove panel and the lock rods are held to the handle with little clips, just pop them off and remove the nuts that hold the handle assembly onto the tailgate, install is just the revers order.

Jun 21, 2009 | 2002 Ford Ranger Regular Cab

1 Answer

91 4 runner tailgate, window wont open


No there is no bypass. The Motor in my tailgate crapped out on me last year partly to do with a rusted out tailgate that let water in! I replaced my tailgate, but in my research found that the only way to get the window down was to remove the inside panels on the tailgate, un screw the cover plate, and then unbolt the motor to allow the window to drop enough to open the tailgate. Once the tailgate is down it will be easier to see the internals and remove the motor. Hope this helps you

May 19, 2009 | 1990 Toyota 4Runner

2 Answers

95 Jeep Grand Cherokee Tailgate Latch


remove all the screws you can and gently pull the panel back. you should be able to see down to the latch assembly and reach the release for the latch

Dec 24, 2008 | 1997 Jeep Cherokee

Not finding what you are looking for?
2001 Volvo V40 Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...