Question about 2000 Mazda Protege

Open Question

1.6 mazda CAMSHAFT TORQUE SEQUENCE 2000 protege

CAMSHAFT TORQUE SEQUENCE 2000 protege

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 423 Answers

SOURCE: Replacing 2 belts on a 2000 Mazda Protege

I recommend that you go to any Auto Parts store and by a repair user manual for your 2000 Mazda Protege.  They have pictures and arrows and stuff that you will need to do the whole job.  The non-Mazda version will cost approximately $15.00.
Because of the tensioner that may come off when while you are doing these belt changes, it is too complicated to talk you through this.
But with the manual, I am confident you can change them.

Posted on Apr 16, 2009

  • 52 Answers

SOURCE: My 2000 Mazda Protege DX has a tight steering. Can

hey srinivasbham,

This is how i would start, the most common problem with loosing your power steering is low fluid. The first thing i would do is check your power steering level. If it is significantly low, this is most likely your problem, just top it off and your on your way. Two other common problems are the power steering pump failing and a loose serpentine belt.

If the pump is failing then it starts to make a groaning noise, but before you think the pump is bad make sure the fluid is full. Also if your serpentine belt is the problem you will get a high pitch squeal while turning.
Start their, and let me know i you need more info.

Posted on May 14, 2009

AaronTech
  • 115 Answers

SOURCE: Locating oil filter on 2000 Mazda Protege

on the backside of the motor, towards the firewall. look above the drive shaft. it's about haft way up the motor.

Posted on Jun 24, 2009

  • 14036 Answers

SOURCE: 01 mazda protege camshaft torque specs

CAMSHAFT BEARING CAPS TORQUE TO 125 INCH POUNDS. CAMSHAFT SPROCKETS - 44 FT LBS. YOU NEED A REPAIR MANUAL LIKE A CHILTON WITH CAMSHAFT TORQUE SEQUENCE DIAGRAM. YOU HAVE 20 CAMSHAFT CAP BOLTS THAT HAVE TO BE TORQUE IN SEQUENCE.

Posted on Mar 21, 2010

Testimonial: "Thanks that was very quick and right on he money "

ftw1952
  • 10319 Answers

SOURCE: how to replace a timing belt on a 2000 Mazda Protege

Here is a website that a free manual can be down loaded for your vehicle


http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazdaprodege 1.6 2000 rodbearing bolt torque


Call the service dept. at your local Mazda dealer and they should be able to tell you the rod bolt torque value.

Mar 13, 2015 | 2000 Mazda Protege

1 Answer

2000 mazda protege correct timing mark alignment


Presuming the timing belt has not been removed or has skipped.
If the belt is removed or skipped this is an interference engine, valves and or pistons could be damaged by turning crankshaft, seek professional help.
Turn crankshaft clockwise and align timing marks (see jpg).
Face the marks (I) and (E) of the camshaft straight up, then align the timing marks with the horizontal surface on the cylinder head.
Pulley boss position pin on the crankshaft should be facing straight up.
25327211-bog4asmiohngydsbtkv4ivhw-1-0.jpg
This is only the beginning of an involved process, 3 pages in shop manual. I recommend getting a manual, many available on line. one typical Mazda 323 Protege Repair Manual 1990 2003
insure that the manual you get has info on your engine.

Dec 18, 2014 | 2000 Mazda Protege

1 Answer

Could you tell me the cylinderhead bolt torque for a 2003 mazda protege 2.0 litre engine with dual overhead cam and no turbo


First torque them in sequence to 13-16 ft.lbs.then in sequence to 85-95 degrees next do the same thing again torque to 85-95 degrees.

Jan 27, 2012 | Mazda Protege Cars & Trucks

1 Answer

I need the 2003 Mazda 6, 2.3 - 4 cylinder main bearing torque specs and sequence asap please.


zjlimited_34.jpg

Fig. Loosen the remaining camshaft cap bolts using this sequence-2.3L (KJ) engine


zjlimited_35.jpg

Fig. Tighten the camshaft cap bolts using this sequence-2.3L (KJ) engine

Nov 09, 2010 | 2003 Mazda Mazda6

1 Answer

01 mazda protege camshaft torque specs


CAMSHAFT BEARING CAPS TORQUE TO 125 INCH POUNDS. CAMSHAFT SPROCKETS - 44 FT LBS. YOU NEED A REPAIR MANUAL LIKE A CHILTON WITH CAMSHAFT TORQUE SEQUENCE DIAGRAM. YOU HAVE 20 CAMSHAFT CAP BOLTS THAT HAVE TO BE TORQUE IN SEQUENCE.

Mar 21, 2010 | Mazda Protege Cars & Trucks

Not finding what you are looking for?
2000 Mazda Protege Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...