Question about 2004 Isuzu Rodeo

Open Question

HOW TO INSTALLING A CAMSHAFT POSITION SENSOR ON 3.2 V6 DOCH RODEO

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
stevenhurc
  • 450 Answers

SOURCE: where is located the canshaft position sensor on

left head at rear near inlet manifold make sure connector faces rearwards if replacing it because you need to turn it to get it in and out with out taking manifold off.

stevenhurc_19.jpg

Posted on Sep 01, 2011

Ad
wilsodfarm
  • 986 Answers

SOURCE: WHERE IS CAMSHAFT POSITION SENSOR ON 2000 RODEO

left front of the engine

Posted on Dec 10, 2009

stevenhurc
  • 450 Answers

SOURCE: where do i locate the

it is located on the inner rear section of the left hand head (left side of vehicle) under inlet manifold dont need to remove inlet manifold
and connector must face rearwards to work correctly


stevenhurc_4.jpg

Posted on Feb 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the crankshaft position sensor on a 2004 isuzu rodeo 3.5


2004 no vin code posted nor the 8th VIN digit for engine code
so answers get 10x harder, lacking that one fact. USA car?
Coin toss 1:
learn the real name of engine, first
6vE1, 4 cams, and last year has VVT, (not trivial that)
and has 2 Cam sensors. to make VVT happy,. dig?
weve answered this many times here, over and over
did the scan tool tell you its bad.?
its on the rear of both heads,

the post above is wrong, he shows the 6vd1w engine,
here just for fun, again i post all V6,s just for you, and others too lazy to search or learn engine REAL NAME.

ill do all 3 V6 engines now.

3de1f741-1946-4f53-9161-03418aaee9a6.jpg


32dohc-kak3wjrwg2pwaolcwur0ctxj-2-2.jpg


32sohc-kak3wjrwg2pwaolcwur0ctxj-2-3.jpg


6ve1-kak3wjrwg2pwaolcwur0ctxj-2-4.jpg


left96-kak3wjrwg2pwaolcwur0ctxj-2-5.jpg


vin2004-kak3wjrwg2pwaolcwur0ctxj-2-6.jpg

Mar 18, 2017 | Isuzu Cars & Trucks

1 Answer

Where is the location of the camshaft sensor for 1995 Isuzu Trooper


no engine stated, 4 banger or v6 but same answer.
there is no such sensor until 1996
why not post the problem or a symptom
and ask for help.
like
wont' crank.
cranks but will not start.
starts and stalls.
starts, runs but misfires.
like that.
get a tuneup yet?> (crystal ball)
V6 (guessing yours)
if you meant crank sensor its on the right side of engine block center.

seen here, CKP "crank sensor"
if you look for a CMP on line you will find it
but its Bunk, it's not there, stores mix parts up. et cetra.
http://jeepdied.com/look/alien-stuff/Isuzu/head%20cam%20sensors/CMP-wonder.pdf


836e5646-c779-44fe-b203-3249404738be.jpg

Dec 20, 2016 | Isuzu Trooper Cars & Trucks

2 Answers

How do i replace the camshaft sensor on a 2004 rodeo


2004 had two engine but the early 2004 might have the 4 bangers , but the 4 banger dropped soon after July 2003 build day..

3.2 L 6VD1 V6 (gasoline)
3.5 L 6VE1W V6 (gasoline) a twin cam V6. !! unique.


in the next post i show all sensors. (most)

Aug 09, 2015 | 2004 Isuzu Rodeo

1 Answer

2002 isuzu rodeo 2.2 liter code P0341 cmp range or performance problems


P0341 ISUZU - Camshaft Position Sensor Performance
Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sep 10, 2012 | 2002 Isuzu Rodeo

2 Answers

My 2002 alero has 65,000 miles and ran great until I was in an accident a few days ago. I tried to start it and it wouldn't start. The check engine light came on and the low track light too. After a few...


Sounds like the Crankshaft sensor is damaged and needs to be replaced.
The Camshaft position sensor works along with the Crankshaft position sensor.
Determining the timing and injectors’ pulse, to deliver fuel to the cylinders.
The Camshaft position sensor is a hall sensor, which it triggered by a magnet in the Camshaft.

On 4 cyl(2.4) models the Camshaft position sensor is located to the left side of the timing cover.
On the V6(3.1 & 3.4) it’s located at the front of the engine block (passenger side), below the power steering pump.
Check the terminals for breaks and looseness, repair if needed.

Here is the plug indentification picture.
The wires are different for the 4cyl and V6, Please note below.
Though the plugs are the same three wire connectors.

Plug is as listed : 1 - Camshaft position sensor signal on 4 cyl,
12 volt supply on the V6
2 – Sensor ground 4 cylinder,
Camshaft position sensor signal on the V6
3 – 12 volt supply on the 4 cylinder,
sensor ground on the V6

First check for voltage and ground circuits from the PCM.
Disconnect the electrical connector from the Camshaft sensor and connect the positive lead (on the wiring harness) of the voltmeter to the red wire(#3) on the 4 cyl and the red/white wire on the V6(#1).

Connect the negative to the pink/black wire on the 4 cyl(#2), or black on the V6(#3).
Turn the key on, the voltmeter should read 12 volts, if not check the wiring to the PCM.
If the circuits are good, have the PCM checked out by a Dealer or other properly trained shop.

To check the operations;
Reconnect the Camshaft position sensor, using a probe to back probe the brown/white wire terminal of the camshaft PS. Plug locations on4 cyl (#1) and theV6(#2)
Connect the positive lead of the voltmeter to the probe and the negative to a good engine ground.
Turn the key on, the voltmeter should read approx 10 volts.

*Rotating the engine by hand with a breaker bar attached to the crank pulley. Watching the voltmeter, the voltage should remain a steady 10volts then quickly drop to zero and back to 10vlts as the magnet passes the sensor.
If the tests results are incorrect then replace the camshaft position sensor.

* Rotating the engine slowly, and at least two full revolutions of the engine for accurate results.


Camshaft sensor Replacement

On the 4 cylinder
- Disconnect the electrical connector
- Remove the camshaft position sensor-mounting bolt and pull the sensor out of the camshaft cover.
- Replace the “O” ring and lightly lubricate it with clean engine oil.
- Install in the reverse of those procedures.

On V6
- Remover the drive belt.
- Remove the power steering unit but don’t disconnect the hoses, just lay it aside.
- Disconnect the electrical connector from the harness; paying attention to the route the wires are in.
- Remove the camshaft ps mounting bolt and pull the sensor out of the block.
- Install in reverse procedure.

If the sensor flange breaks off and you cant remove the CPS, try screwing a heavy screw into the top of the sensor and pulling it out with plyers/vise-grips.

Good luck and thank you for using Fixya

Mar 10, 2010 | 2002 Oldsmobile Alero

1 Answer

What sensor is controlled by the accelerator pedal? What sensor controls spark timing? Both on a 1997 v6 Rodeo.


Hello Wayne.
When you depress your accelerator pedal it increases the voltage output of the throttle position sensor mounted on the end of the throttle shaft.
No one sensor adjusts timing though. The inputs from several sensors are integrated inside the ECU computer. Then the ECU adjusts the timing accordingly.
Base timing is taken from the crankshaft position sensor and the camshaft position sensor.
Engine temperature, engine load, revs per minute, gear ratio, speed all have the most effect, but there are others that will have slight effect as well.
If you have any more questions leave them in "add comments" and I will return your question.

KL

Dec 17, 2009 | 1997 Isuzu Rodeo

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Cant find cam sensor in 2004 dodge stratus r/t


2.0L 2.4L it is on The BACK OF the Cylinder Head REMOVAL
The camshaft position sensor is mounted to the rear of the cylinder head.

  1. Remove the negative battery cable.
  2. Disconnect the PCV hose and reposition.
    1. Disconnect electrical connectors from the camshaft position sensor.
    2. Remove camshaft position sensor mounting screws. Remove sensor.
      1. Loosen screw attaching target magnet to rear of camshaft and remove magnet.
      INSTALLATION
      The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.

      1. Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
      2. Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
      3. Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins.
      4. Connect the PCV Valve hose.
      5. Connect the negative battery cable.
2.7L V6
REMOVAL
The camshaft position sensor is mounted in the front of the head.
  1. Disconnect electrical connector from sensor.
  2. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
  1. Without pulling on the connector, pull the sensor out of the chain case cover.
INSTALLATION
The camshaft position sensor is mounted in the front of the head.

  1. Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
  2. Attach electrical connector to sensor.

Feb 12, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
2004 Isuzu Rodeo Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...