Question about 1998 Ford Contour

Open Question

Need a brake line diagram for a 98 ford contour

How to install brake lines from mastercyclinder to caliper

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 91 Answers

SOURCE: 1998+ford van 150+brake lines+diagram

I only replace what is needed they are time consuming and all four breaks will need to be bleed only diagram is what you have under the van cut out the damaged section take it to parts store and get the size you need make sure you get all fitting at this time also good luck

Posted on Apr 28, 2009

ZJLimited
  • 17970 Answers

SOURCE: 98 ford contour wiring diagram

When you tell us "wiring diagram", is for one specific circuit or you are refer to the firing order?

Posted on Apr 13, 2010

duane_wong
  • 6826 Answers

SOURCE: 1997 ford escort brake line diagram

The LF and RR are in an independent circuit of the RF, LR wheels. The master cylinder already has the lines hooked up in a way that if you trace the lines, you can make your own diagram.

Posted on Aug 03, 2010

  • 4369 Answers

SOURCE: im looking for a brake line diagram of all the

Disconnect the hydraulic brake lines.

  1. Disconnect the inlet hydraulic brake lines.
  1. Disconnect the outlet hydraulic brake lines.

f7ac73e.gif

Posted on Aug 19, 2010

  • 1 Answer

SOURCE: i need a diagram of brake line routing for 1996 ford taurus

brake problem in 1996 ord taurus

Posted on Oct 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my ign fuse located on my car


Below dash instrument panel, R16 ignition relay
98 Ford Contour SE Fuse Box Map
Fuse Panel Layout Diagram Parts: passenger side air bag, heater blower, interior lighting, heater blower motor, parking lamp, interior lighting, electric mirror, clock, wiper motor, ignition, reverse voltage protection, rear window defrost, engine management system, instrument panel illumination, radio, wiper motor, power windows, ABS module, backup lamp, brake lamp, door lock, main light, cigar lighter, electric seats,
link below should be the same as yours, press the helpful button

http://www.autofuseboxdiagram.com/1342-98-ford-contour-se-fuse-box-diagram

Jan 30, 2016 | 1999 Ford Contour

1 Answer

How do I replace the metal brake lines on a 1997 ford contour?


You remove the metal brake line or lines then measure how long the line is and your auto parts store should have it, but you will have to bend it out yourself they do have tube benders for doing that and thats the best way but i have done it by hand. install new line and bleed system.

Feb 26, 2015 | 1997 Ford Contour

1 Answer

Diagram of brake line on front passenger side for 1998 Audi A4. Question? Does the 98's have the senor on the brakes, as my neighbor changed my brakes last nite and said, the old ones dont have the...


Was the brake line removed ? There is no reason a brake line needs to be replaced unless the line was broken or damaged.
One way to check if your car has sensors, is to look for a harness that runs and is secured on the strut. Also check the hub, there is usually a slot in the back where the sensor is mounted.
Some vehicles come without brake sensors, best thing to do is call local dealer, supply them with your VIN and ask them if it comes with sensors.
What were the repairs done to your brakes ? What is the problem after the repair was done ? You may only need to bleed the complete system if calipers were replaced.

Jun 17, 2017 | 1998 Audi A4

3 Answers

All of a sudden i have spongy brakes on my 92 f 250. changed master cyl and booster. and rubber brake hoses. still spongy and nothing is leaking.brakes went from being good to spongy in one...


Check the rear wheel cylinders? Was anything leaking at the master cylinder? Does it have ABS?
Check the front caliper slides are free. Check the front caliper pistons for leaks as well. This is all assuming you bled the brakes(all 4 wheels) properly after all that replacement! You're getting air from somewhere for sure or if it has ABS, the pump may have a problem.

Apr 30, 2011 | Ford F-250 Cars & Trucks

2 Answers

Where can I find a brake line diagram for 1995 ford contour.


You buy brake tubing at the auto parts store,and fabricate what your replacing.
Have to know, how to bend and flair tubing, and have the necessary tools.

Oct 06, 2010 | 1995 Ford Contour

1 Answer

How do I install rear brake pads on a 2008 ford fusion once calipers are removed?


unplug the brake fluid line from the caliper than squeeze the cylinders open then insert your new brakes into the clips then add more fluid and bleed the lines connecting them back to the brake caliper

Mar 10, 2010 | 2008 Ford Fusion

1 Answer

Replace rusted brake lines for ford van F150 1998. How i bleed the brakes


There is a bleeder screw at each caliper/wheel cylinder. You looosen this screw (don't remove it) and have someone depress brake pedal and hold it down. Tighten bleeder screw, release brake pedal, and repeat until you get only fluid (no air) from the bleeder.

Catch the fluid in something to kep it off the ground. Make sure you keep the master cylinder reservoir full of fluid during this process or you'll get air back in the lines.

You may have to do this several times for each wheel.

May 04, 2009 | 1997 Ford Contour

1 Answer

Im putting a brake line on for a 2003 Ford Contour and i need a diagram


You have the best possible diagram: look at your brakeline and duplicate as best you can. (does not have to be perfect, just has to be connected well on both ends and not interfere with any moving parts). avoid places where it could rub through and use small sections of rubber hose to eliminate vibration and rubbing Use as many of the original fasteners as possible along the line. Bleed system completely when installed.

Mar 27, 2009 | 1994 Ford Probe

Not finding what you are looking for?
1998 Ford Contour Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...