Question about 1992 Plymouth Acclaim

Open Question

Whats the codes for the flashing check engine light mean when i turn the key 3 times?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 77499 Answers

SOURCE: 1989 plymouth horizon check engine light on

Code 34 is set when the computer does not detect a voltage to and through the speed control servo. The cruise control computer is built into the PCM, which grounds two windings in the servo mechanism to regulate the vacuum applied to the servo diaphragm.
Note: All Chrysler corporation fuel-injected engines have the computer circuitry and software for the cruise control system installed, even if there is no cruise control installed on the vehicle. If there is no cruise control installed on the care or truck, the computer will interpret this as an open winding and set code 34.
First: turn the key ON, turn the cruise switch ON, and look for +12 Volts on the dark blue/red wire that connects to the servo mechanism. This circuit is fed:

  • from the ignition switch through to 10 (dark blue wire)
  • from fuse 10 to the steering column (white/red wire)
  • through the clock spring to the cruise control ON/OFF switch on the steering wheel (white/red wire)
  • back through the clockspring to joint connect "C" (yellow/red wire)
  • to the brake lamp switch under the dashboard (yellow/red wire)
  • through the firewall from the brake switch (dark blue/red wire)
  • to the servo (dark blue/red wire) A break anywhere in this path (broken wire, bad brake switch, loose connector, etc.) will interrupt the 12 volt supply to the servo and set a fault code. Work backwards until you locate the break.
Turn the key OFF. Unplug the the connector from the servo and measure the servo coil resistances.
  • measure the resistance between the servo pin that connects to the tan/red wire and the servo pin that connects to the dark blue/red wire.
  • measure the resistance between the servo pin that connects to the light green/red wire and the servo pin that connects to the dark blue/red wire. The resistance in both cases should be above 0 ohms and less than infinity.
Disconnect the battery(s). Unplug the 60 pin connector from the PCM and check for continuity between the pcm connector and the servo connector for the tan/red wire (cavity 33) and the light green/red wire (cavity 53).
If no wiring problems are found, check the PCM connectors for corrosion, and reconnect. Reconnect the battery and test the circuit again. If the problem still exists, the PCM is probably bad. NOTE: Personally, if the truck was out of warranty I would try to find for a used servo before buying a new PCM.

Posted on Oct 16, 2008

Ad
Murphybanton
  • 2004 Answers

SOURCE: check engine light flashing a code. what does this mean

Please visit http://www.troublecodes.net/neon/

for clarification of your error code. But I strongly believe you fixed a low rated fuel pump.

also from your explanation you got code 55 which means no error code was recorded.

Rate this please.

Posted on May 29, 2009

  • 5 Answers

SOURCE: what does it mean when the check engine light

the engine is skipping and causing a polution problem. this is a bad engine skip and will need to be taken care of before engine damage occures.

Posted on Jan 17, 2010

  • 118 Answers

SOURCE: 1990 Voyager. Need code

here you go hope it helps,dont forget to vote on answer thanks
88–95 3.0L (Except Monaco, Premier & Stealth),
3.3L, 3.5L & 3.8L Engines
11
Engine Has Not Been Cranked Since Battery Was Disconnected{4}
No Crank Sensor Signal During Engine Cranking{3}
12
Memory Standby Power Recently Lost
13
MAP Sensor Pneumatic Circuit
14
MAP Sensor Electrical Circuit
15
Vehicle/Distance Sensor Circuit
16
Loss Of Battery Voltage Sense
17
Engine Running Too Cool
21
Problem In Oxygen Feedback Circuit
22
Coolant Temperature Sensor Circuit
23
Charge Temperature Sensor Circuit
24
Throttle Position Sensor Circuit
25
AIS Motor Drive Circuit
26
Injector Current Limit Not Achieved
27
Injector Driver Interface Circuit{1}
Injector Control Circuit{2}
31
Purge Solenoid Circuit
32
EGR Diagnostics
33
A/C Cutout Relay Circuit Or A/C Clutch Relay Circuit
34
Fault In Speed Control Solenoid Driver Circuit
35
Fault In Fan Relay Circuit
37
Part Throttle Unlock Solenoid Driver Circuit
41
Fault In Charging System Or No Field Current
42
Fault In ASD Relay Driver Circuit
43
In Ignition Coil Control Circuits
44
Lose Of FJ2 To Logic Board
46
Battery Voltage Is Too High
47
Battery Voltage Is Too Low
51
Lean Condition Is Indicated
52
Rich Condition Is Indicated
53
Internal Problem In Module
54
Fault In Distributor High Data Rate Pickup Circuit{1}
No Sync Pickup Signal{2}
55
End Of Message
62
Unsuccessful Attempt To Update EMR Mileage
63
Fault Error{1}
Controller Failure EEPROM Write Denied{2}
65
Manifold Tuning Valve
66
CCD Bus System
77
Speed Control Relay Circuit

{1}—1988–91 models.
{2}—1992–95 models.
{3}—1990–95 models.
{4}—Neon.
If you need more just ask Thanks Db

Posted on Aug 19, 2010

  • 1565 Answers

SOURCE: How do I find what the codes mean from a flashing

turn key as follows;

off-on, off-on, off-on on is when the dash lights come on, and off is one click back from on. do not start the car.

The codes will flash out in pairs of numbers using the check engine light. 5-5 is the end of the test.

just google the code number; for example, "dodge code 55". This should tell you the meaning of the code. or check this link.

http://www.dodgetalk.com/forums/showthread.php?t=104185

Posted on Aug 15, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you get what the check engine light code for this car


are you asking how to get the code from the ECM. if so you turn the key to the start position turn off, turn on, turn off, turn on and leave in this position. then count the # of times check engine light flashes. it will flash the first number then stop for a second then flash the second #. it will do this 3 times for each code. then you check to see what the code translates to so you know were to diagnose.

Mar 14, 2015 | 1990 Plymouth Laser

1 Answer

2002 dodge intrepid sxt 3.5l. what does 10 flashes of check engine light mean?


Are you sure is not 5 flashes with a short pause in between and then 5 more flashes? Code 55 indicates the end if the diagnosis.

Mar 02, 2013 | 2002 Dodge Intrepid

1 Answer

I have a 1994 plymouth voyage se and it will not strat. It tell me to check gauge light comes on. what should i do or what does that mean?


Turn key to on ( not start) then off, then on, then off, then on and leave on, and have a pen and paper ready to record flashes of "check engine light". It will flash then pause between second number of 2 digit code. Then a short pause and flash again, pause, then flash. For example: if it flashes 2 times, then pause, then flashes 2 more times, that would be code 22. If it flashes 3 times, pause, then flashes 5 more times, that would be code 35. As I said, there will be a short pause between 2 digits, as well as after number. Write them down as they come up and get back to us with those codes for advice. When you get code 55 ( 5 flashes, pause 5 more ) that means end of message. Those codes should point everyone in right direction of trouble spot.

Jul 31, 2011 | 1991 Plymouth Grand Voyager

2 Answers

Error codes for 1991 dodge spirit


Turn the key to run then off, back to run, then off, then to run and leave it on. The check engine light will be on and will then go off and then on again according to the codes the engine controler happens to have in it. If the check engine light was on when you stopped the car, then there is at least one code in the controler. The light will blink the codes like this.
Cycle the key three times and leave on on the third time. light on for about 3-4 seconds then goes out for about 2 seconds and then blinks one time and goes out for 3 seconds this is for the no.1. Then the light blinks 3 times and goes out for about 3-4 seconds. You have the code 13. You could have a whole string of codes in the controler memory. It could be something like this. key cycled 3 times, light on for 3-4 seconds, then blinks 1 time, pause, 3 times, longer pause, 2 times ,pause 4 times, longer pause, then 5 times, pause 5 times the goes out.
This is code ; 13,24, 55. code 55 isn't really a code. It just tells you it's the end of any codes the controller has.
If you disconnect the battery and hook it back, you will have code 13 which simply mean 'battery disconnect'. It will errace it's self after several starts if it's not disconnected again. If you cycle the key and you get 55, this means there are no codes recorded at this time.
You will allways get 55 when checking for codes wheather there are fault codes or not. The light on for a few second before the codes start flashing is only a bulb check. Some codes like 13 will not turn the check engine on, but but will leave a code for diagnostic purposes only. If you have the check engine light on and accellerate and the light begains to blink, then the controller is telling you that you have an engine miss and are running the chance of burning out you're catalatic converter if you continue driving. Sometimes its advised to disconnect the battery after you have recorded the codes.
This will erase all codes that are present but were generated by conditions that aren't pertanent to the present condition. and then the codes that come back are the real ones to address.
This link: http://minimopar.knizefamily.net/fault/index.html
Contains the entire list of Chrysler Engine Error Codes.


Mar 03, 2011 | 1991 Dodge Spirit

3 Answers

How to get the trouble codes for a 1992 dodge spirit


turn the key on,off,on,off,on,the check engine light will flash the codes.For instanse code 34 would be 3 flashes,a pause ,then 4 flashes.Will always have a 55 code because the engine is not running.

Feb 23, 2011 | 1992 Dodge Spirit

2 Answers

How do you read the codes


2 ways. 1) with a code reader from autozone (they do it for free by the way). and 2) use the cars key by turning the ignition key on and off 3 time and the 3rd time leave it on. do not go all the way to start. don't crank engine. just on. wait a few seconds and the check engine light will start to flash the codes(or power loss light). it will flash the first digit then pauses for a few sec. and then flashes the second digit. must count the flashes and write them down. for example first 2 flashes means 2 pause then 3 flashes means 3. that is code 23. that may not exist but is just an example to let you now how it woks. good luck.

Sep 10, 2010 | 1990 Dodge Dakota

5 Answers

96 2.5 cherokee 2dr sat for a month, charged batt. , drove 4 miles, died, no power. had alt. tested, passed, got new batt., now it turns over but will not fire. Please help!


Make sure that all the wiring disturbed by the battery change was restored. Do you have the check engine light on? If so, rent a scanner and read out any code(s). Pursue the codes to repair(s). You can check the ignition by removing one spark plug wire, connect it to a spare plug and set the plug base on the engine. Have someone try the starter while you watch the plug--it should flash at regular intervals while the starter turns. If ok, let the car rest for a while, then have someone turn-on the key (don't try to start) while you listen at the fuel tank. You should hear the fuel pump run for a short time, then quit. That means the pump has built pressure and is awaiting start. If it continues to run, the pump may be toast and should be replaced. Change the fuel filter.

Aug 25, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Will not start just died.


Engine? Those flashes should be 2 digit numbers . Cycle key, on, off, on, off, on & leave on & recount those flashes. Example: 3 flashes, pause, then 3 more is code 33. Or 2 flashes, pause, 4 flashes, is code 24. 5 flashes, pause 5 more, is code 55 which means end of message. Then get back.

May 31, 2009 | 1989 Dodge Caravan Cargo

1 Answer

Check engine light, but no code


first what year it may be obd1 system roll key on and off 3 times if it is obd1 it will start flashing first code will be 1 flash then 2 quick flashes this is code 12 thta means computer is reading codes then just start counting flashes they will be intermitant ie 1 flash then 3 quick flashes means 13 and so on when you get to the end of codes it will flash 5 quick then 5 quick again that is the end of your codes

Apr 02, 2009 | 1996 Jeep Cherokee Sport

1 Answer

Check enggine


Do a self test. Turn key to on position and back to off position 3 times. a series of flashes will commence from the "check engine" light. The first set of flashes is the 1st digit of the code, then there will be a pause, then a 2nd set of flashes, This will be the 2nd digit of the code. For example, 3 flashes, pause, 7 flashes, means code 37. Check what the code means in a Haynes auto repair manual. This will tell you what the engine light on your car means.

Jun 12, 2008 | 1998 Jeep Cherokee

Not finding what you are looking for?
1992 Plymouth Acclaim Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...