Question about Mitsubishi Cars & Trucks

1 Answer

Hhow to adjust valve clearance? - Mitsubishi Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mitsubishi Master
  • 3,103 Answers

Call the parts store for your car info and specs..good luck..

Posted on Jan 21, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 883 Answers

SOURCE: I want to know the valve clearance adjustment.

intake .22 to .28 mm
exhaust .27 to .33 mm
rate me solved...this is all I can find

Posted on Jun 27, 2008

starlet4life
  • 89 Answers

SOURCE: Adjust valve clearances 1987 toyota corolla

Im assuming its an 4AGE!?
http://www.ae92gts.com/ae92gts_valve_adj.html
And here one of my favorites...;)
http://www.billzilla.org/4agstock.htm

Posted on Oct 07, 2008

  • 1 Answer

SOURCE: Valve tappet adjustment

well, I can see ur message has been here for quite some time. Most probably you got the answer to ur request.
I just did the valve clearance on the engine of my SJ413 that has the 1000cc engine of an SJ410 :
When cold: 0.13mm Intake and 0.18mm Exhaust
Engine sounded well and worked fine after that.
Enjoy
Mehdi

Posted on Feb 07, 2009

  • 54 Answers

SOURCE: Need Valve clearance for '93 kh ford laser

0.10 - 0.15mm inlet
0.18 - 0.23mm exhaust
but you must be carefull because the top of the valve seat becomes concave from wear, a feeler guage will not give the most accurate reading, hope i have been of some hel

Posted on May 14, 2009

  • 73 Answers

SOURCE: valve adjustment

tiburon uses hydrolic lash adjusters there are no valve lash adjusting If you hearing a pecking sound on the top of the mtr try some oil additive or replace the hydrolic lash adjusters

Posted on Jun 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Valve clearance


Valve clearance Google search your year make and model valve clearance. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Checking and adjusting valves
Engine Valve Adjustment Procedure The Right Way
Valve Clearance Adjustment
Valve clearance Google Search

Aug 10, 2016 | Cars & Trucks

1 Answer

Valve clearances


With such a late model car I suspect you have hydraulic tappets which means the clearance is automatically adjusted when you start

May 05, 2013 | 2010 Suzuki Kizashi

1 Answer

I need the required valve & inyector clearance on a M11 engine


Cummins M11

Intake valve clearance 0.010 inch
Exhaust valve clearance 0.024 inch

The firing order is 1-5-3-6-2-4 and that is the order the valves should be adjusted started with first timing mark on main pulley adjust cylinder number 1 The valves and injector should be adjusted at the same time The crankshaft is then rotated 120 degrees to next timing mark and cylinder 5 is adjusted, the crank is rotated again 120 degrees to next timing mark and cylinder 3 is adjusted.then back to the first timing mark, cylinder 6 is adjusted, etc/

Adjusting nut on plunger should be adjusted to the point where you feel the plunger just reaches the bottom.of travel/bottoms out.

Feb 15, 2012 | Cars & Trucks

1 Answer

What is the difference between hot and cold vavle clearances


When it is stated that valve clearance should be set when hot, you first adjust the clearance on the cold engine after assembly to the hot setting specs if they are the only ones given, then let the vehicle warm up to operating temperature. Then adjust the clearances again.
If it is just a tune-up(undisturbed engine), let the engine warm up to operating temperature, then adjust.
The reason is that metal expands as it heats up, which affects the valve clearance.

Dec 05, 2010 | Toyota Land Cruiser Cars & Trucks

2 Answers

Overhead valves making noise like they need ajusting


Valve Lash ADJUSTMENT 1.6L Engines NOTE: Measure valve clearance with the engine cold.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the valve cover.
  3. Set the engine to Top Dead Center (TDC) of the compression stroke for the cylinder to be adjusted.
  4. Check the valve clearance. The valve clearance specifications are as follows:
    • Intake valves: 0.005-0.007 inches (0.13-0.17mm)
    • Exhaust valves: 0.005-0.007 inches (0.13-0.17mm)
  5. After adjustment, tighten the locknuts to 11-14 ft. lbs. (15-19 Nm).
  6. Repeat for each valve to be adjusted.
1.8L, 2.0L and 2.5L Engines The 1.8L, 2.0L and 2.5L engines utilize automatic hydraulic lash adjusters to maintain proper valve lash at all times. Periodic valve lash inspection and adjustment is not necessary or possible. prev.gif next.gif

Sep 14, 2010 | 2000 Chevrolet Tracker

2 Answers

Procedure of tappet adjustment


make sure engine is warmed up. Put cylinder one at top dead center,remove the valve cover,loosen all adjustment lock nuts,adust intake and exhaust valves on cyl #1 and intake valve on #2 and exhaust valve on #3. now rotate crankshaft 360 degrees clockwise, now adjust intake valves on cyl#3 and cyl #4 and exhaust valves on cyl #2 and cyl #4.now tighten lock nuts and install valve cover. specs are intake valves 25mm clearance and exhaust 28mm clearance, use a feeler gauge,heres a picture to show you where to check clearance.7675a52.gif

Mar 14, 2010 | 1986 Suzuki Samurai

1 Answer

How to adjust valve clearance on a 1999 sunfire 2.2L engin. I heard noise in my engine and I am thinking its only the valve clearance need to be adjust.


There is no valve adjustment for that engine, Hydraulic lifters, You might remove the valve cover and see if you have a rocker arm loose

Mar 13, 2010 | 1999 Pontiac Sunfire

1 Answer

I did a valve adjustment and now it wont start


You adjusted the valves too tight. Back off of the adjustment before you break parts. You Have to set the rocker arm clearance when the engine is cold. (Not warm, not hot)

Use a feeler gauge.
The clearance for the Intake valves is .007 to .009. (7 to 9 thousandths)
The clearance for the Exhaust valves is .009 to .011 (9 to 11 thousandths)
You want a slight drag when you pull the feeler gauge through. This technique takes a certain amount of 'Feel'.

Jul 31, 2009 | 1999 Honda Civic

1 Answer

Want to know what the valve clearances are for my 1999 hyndai excel


Adjust the jet valve clearance before the adjustment of the
intake valve clearance.
Jet valve clearance (hot engine)
[Standard value]. . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

now adjust valve clearance
Valve clearance (hot engine) [Standard value]
Intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.15 mm (0.006 in.)
Exhaust. . . . . . . . . . . . . . . . . . . . . . . . . . 0.25 mm (0.010 in.)

Jul 30, 2009 | 1990 Hyundai Excel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...