Question about 2004 Ford Escape

Open Question

How to change a coil pack in a 2003 ford escape

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: ford escape Rear Suspension With Coil Springs - out of joint?

It is a 4x4. The "yellow" looking item in between/inside the black spring coil seems to be out of its joint. When I compare the left vs the right, the left side is sitting up high, while the right side appears to be settled into place.

Posted on Nov 13, 2008

  • 1 Answer

SOURCE: 1990 ford ranger no fire through plug wires

Does it have a TFI module on the distributor. A local parts store should be able to test that for you.

Posted on May 16, 2009

  • 6 Answers

SOURCE: headlight went out in 2003 ford escape i have

you have to remove the whole headlight assembly, then pop off the front cover pull the old bulb out and put the new one in. reverse the process to re-install. there is a small plastic tab on the topfront of the headlight assembly, that is what you need to release to get the clear cover off and get inside.

Posted on Oct 07, 2009

  • 312 Answers

SOURCE: Ford Escape 2003. Engine suddenly overheat.

Engine over heating can be caused by a number of things. When you say the water pump and radiator appear to be ok I am also guessing that you checked the coolant level to make sure it is normal.

If the level is low then you obviously have a leak. Insufficient coolant circulating will not cool the motor properly because it won't be able to draw enough heat out. If the level is normal then you need to check the thermostat to make sure it is opening properly. To do this, run the motor to temperature and check the top and bottom hoses. They should both be hot and firrm once the thermostat opens meaning the circulation loop is operating properly. If the top is hot and firm and the bottom is cold/soft or collapsed then the thermostat isn't opening.

If the thermostat is operating properly then you ned to look for some other obstruction or cause for coolant loss. Check the head/intake gaskets, hose connections, hoses, over flow tank, radiator fins, radiator side tanks etc..

Good luck.

Posted on Jun 10, 2010

Testimonial: "Thank you for your quick response. I will get the head/intake gasket checked."

  • 45 Answers

SOURCE: how to change ignition coil pack on 2003 ford

the coil pack is located on nthe back valve cover, bank1, towards the firewall.
it mounts with three bolts or torx screws.
it is kinda hard to get to but just pull off the plugwires and
it will give you more room.
there is also i radio capacitor thing that is retained by one of the bolts,

Posted on Aug 06, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What coil pack will interchange with 2003 escape 3liter

Only the one that is intended for this engine will work.

Sep 05, 2016 | 2003 Ford Escape

1 Answer

How to fix ford escap 2002 v6 missing 4&6cilander

if that is what code your getting from computer scan ,most likely its a coil pack gone bad ,one way to check is to change one with one from an different cylinder 1, 2,3,5, and see if misfire codes change to those cylinders ,if it does replace those.coils. coils cost about 50.00 new

Sep 09, 2014 | 2002 Ford Escape

2 Answers

Ford Escape 3.0 no power to #4 coil

Need to change the coil. Is likely the problem. Sometimes that means replacing the whole coil pack.

Apr 10, 2014 | 2005 Ford Escape

1 Answer

When it rains my 2003 ford escape v6 misfires and runs rough

coil pack(s) are bad. go to local auto parts store and they will test your check engine light to tell you what cylinder is misfiring. these parts arn't cheap. when looking at the motor, cylinders 123 are in the back from left to right, 456 are in the front and easy to do. however, changing the back coils are more difficult because it requires removal of the plastic intake. maybe 45 min to change all 6

Dec 09, 2013 | Cars & Trucks

1 Answer


You will have to remove the engine cosmetic cover. The 2.0 four cylinder has 1 and the 3.0 V6 has two The 2.0 is a standard single coil pack and will be clearly visible when you take the cover off, just follow the wires and remove the spark plug boots and voila. The V6 uses 6 coil packs and you will have to unscrew their bolts and remove each of them to get at the spark plug underneath them. Make sure you blow away any debris, from around the plugs before taking them out. hope this helps

Mar 28, 2011 | 2003 Ford Escape

3 Answers

I have a 2003 Escape XLT that is misfiring with a code of p0316 and p 0306. What do i need to check or repair?

P0306 is cylinder 6 misfire..P0316 is misfire in the first 1000 revolutions. A proper tune up will probably take care of the code. This includes spark plugs. I have the Mercury Mariner equivelent engine and you will need to remove the upper intake plenum to replace the plugs. It is plastic so take extra care when removing and re installing. I did not have to use new gaskets. There is a "coil pack" on each spark plug so no wires to change. I would change the air and fuel filter also.

Jan 05, 2011 | Ford Escape Cars & Trucks

1 Answer

My ford escape 2003 2.0 move roughly. a mechanic diagnosed it that my car's n0.4 coil pack was not functioning and it needs replacement.he however did not check if my no. 4 spark plug needs to be the one...

swop no4 plug with another one and see if its the same ,if mechanic diagnosed coil pack then i do feel he would be right as the symptoms are different

Oct 22, 2010 | Ford Escape Cars & Trucks

1 Answer

Scan shows a misfire on cyclinders 4,5, and 6. on a Ford Escape.

your ford should have 2 coil packs if 4,5,and 6 are on the same coil pack change it hope this helps CJ

May 24, 2010 | 2004 Ford Escape

Not finding what you are looking for?
2004 Ford Escape Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides