Question about Cars & Trucks

2 Answers

What kind of brake fluid do I need for my 2003 jeep liberty

Posted by on

  • Randy Handy Jan 21, 2013

    If you are still in doubt call autozone and they will tell you what type to use.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Synthetic dot 3-4

Posted on Jan 21, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,103 Answers

D.O.T. number 3 is required for most vehicles and is the nly recommended fluid...even on big trucks.. do not mix fluids PLEASE>>> do not use transmission fluid because its like mixing water and oil( it wont work) only brake fluid..there are different brands but look for the D.O.T. lettering it usually goes into a small tank out front of the drivers side under the hood..if in doubt sk at the parts store...good luck..

Posted on Jan 21, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Brian032472
  • 150 Answers

SOURCE: 2003 Jeep Liberty heater fan problem

It is the blower motor resistor. Look under the passanger side dash and locate the fan housing (looks round and black in color. Then locate the resistor it will be in that housing usually withtwo ten millimeter nuts or two simple screws holding it in. unplug the harness to the resistor and remove the resistor. Part store price is approx. 50.00. Note: on aftermarket (not Jeep) resistor sometimes you have to modify the housing a little to get it in. Hope this helps.

Posted on Feb 01, 2009

michigan man
  • 3533 Answers

SOURCE: how to replace rear brake pads on 2005 jeep liberty

put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Posted on Mar 01, 2009

  • 1 Answer

SOURCE: How to replace reak brake rotors on Jeep Liberty

Replace rear rotors on 04 liberty.
Remove tire & wheel
Remove brake caliper, tie up out of way.
Back off e-brake shoe adjustment.
Remove factory spring clip from lugs (2places)
This is the crude part....
After attempting to pull off disc/drum with puller....I got pretty sick of it. Understand this is in the Northeast with lots of salt on the roads in winter. Needless to say there is a ridge of rust around the inside edge of the e-brake surface. Any more pressure and I was afraid of damage to the e-brake shoe asembly. I then took a small grinder with a cut off wheel and cut the disc thru (used space where caliper usually sits). Also cut nearly through the face between 2 lugs. You can't quite get thru the back corner at the disc. Since the material is cast iron it will crack when you drive a wedge in the slot cut in the disc. This opens the housing around the shoes and it slides off easily. The cutting operation took less than10 mins, alot less than the puller with hammer assist!
I know this is a bit "unorthodox" to say the least, however the object is to remove the old junk disc safely and as quickly as possible, without harming the e-brake parts inside.
Install new parts in reverse order, new pads go in easy after squeezing the caliper piston back with a c clamp as is the normal procedure.

Posted on Mar 22, 2009

  • 249 Answers

SOURCE: 2005 jeep liberty brake lights will not work. I

brake pedal switch, get a wire, unplug plug, bridge circuit and check lights.
plug and switch is high up on the brake pedal not normally easy to get to.

Posted on Aug 15, 2009

  • 114 Answers

SOURCE: Need a Jeep Liberty drive belt diagram.

3f6d05b.gif Here you go

Posted on Oct 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why do I have to apply excessive pressure to the brake pedal?


driving too fast,need to fill master cylinder,water in brake fluid,air in lines,,,,,,,

Jun 01, 2015 | 2003 Jeep Liberty

1 Answer

Type of brake fluid for 2003 jeep liberty


the lid tells that, look first?
so does the operators guide. lost that
2004, may be same, 2003 is not off list.
http://www.jeep.com/en/owners/manuals/

dot/3/4 are most (you look it up , not me)

Feb 16, 2015 | 2003 Jeep Liberty

1 Answer

Bleeding brakes on 2005 jeep liberty


you will have too take brake lines off by the master cyclinder by the brakes and have some one pump the brake pedal in and out catching the fluid in a gug and keep pooring fluid in fill container till all aire is out of lines

Jul 12, 2010 | 2005 Jeep Liberty

1 Answer

2003 Jeep Liberty - recently replaced brake pads and rotors and now drivers side rear wheel will intermittently lock up which creates tremendous heat in the wheel and fries the brake pads. Have had into...


I had the same experience in the past and it turned out to be the caliper that was getting stuck and the pads would not retract away from the rotors causing friction and eventually burning your pads.

May 20, 2010 | 2003 Jeep Liberty

2 Answers

WHAT KIND OF BRAKES ARE ON THE REAR OF A 2002 JEEP LIBERTY


Drum brakes are on the rear of the 02 Jeep Liberty.

Feb 04, 2010 | 2002 Jeep Liberty

1 Answer

Changing rear brake pads on a 2003 jeep liberty


No, do not open the brake fluid lines. If the piston has groves cut in to the face of it, you will need a special compressor for it. Most new cars with 4 wheel discs use this type of piston. Instead of just pushing the piston in (as you would on older style calipers) you actually need to turn it clockwise while you push it in. They sell the tool at auto parts stores.

May 28, 2009 | 2003 Jeep Liberty

1 Answer

How much and what kind do I need to change the differential fluid also what kind of antifreeze do I need for drain and refill


If you are picking the product up at a major auto parts store, they will be able to tell you. you will need to know, Make, model, engine size, Air Contd, 2wheel or 4 wheel drive. Once they have this they can tell you what the recommended products are and the capacity of each.

Hope this is of some help.
ed

May 05, 2009 | 2007 Jeep Liberty Sport

1 Answer

How to replace rear brake pads on 2005 Jeep Liberty


put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Mar 01, 2009 | 2005 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

340 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...