Question about 1999 Chrysler 300M

Open Question

Heater in 1999 chrysler 300m wont turn off

I just comes of and wont turn off I have checked the fuses 17 and 23

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6 Answers

SOURCE: 1999 Chrysler 300m ATC Control Communication Failure

i have the same car and it did the same thing when i got it take it to a dealership there are 2 flashes for the bcm body control module that will recalibrate the automatic temp contol and that should fix the problem

Posted on Apr 01, 2009

morganismo
  • 36 Answers

SOURCE: AC belt on 1999 Chrysler 300M

When you replace the AC belt you really should replace the serpentine belt as well, since you will have to take it off already. If you don't do it now it is inevitable that you will have to replace it in like 3 weeks anyway : )

You need to first remove the serpentine belt by loosening the nut in the center of the idler pulley. After that you will need to loosen the push bolt on the side of the idler pulley. The hub bolt is a 15mm size and the push bolt on the side of the tensioner is a 13mm I think. After you loosen it sufficiently, you will need to pull off the old belt.

Next you will need to loosen the tensioner pulley for the AC belt as well. It is the same process. The main issue is space. You will most likely need to raise your car to get at the right angles to loosen these pulleys.

Once you loosen the idler pulley in the same manner as you loosened the other, you can slip the AC belt onto the back of the crank pulley and route it as the diagram under your hood instructs you. Next tighten up the idler pully in the opposite way as you loosend it...tighten up the push bolt until the belt play is within factory specifications, then tighten the hub bolt in the center of the pulley. Do the same for the serpentine belt and you should be up and running in no time. I just performed these tasks on my 2000 300m and I wish someone would have told me this before I started my project. Hope this helps, Good Luck!

Posted on May 26, 2009

  • 7 Answers

SOURCE: programming instructions for a 1999 Chrysler 300M remote fob

Manual Programming Procedure (non scan tool)
1. Connect pin 1 of the 16-way data link connector to chassis ground or to pin 4 of the 16-way data link connector.
2. Close all doors, turn ignition key to off.
3. Turn ignition key to Accessory.
4. Turn ignition to off, door locks will cycle once (in programming mode).
5. For each key FOB, press any button 3 times in a row to program code. When programming is complete, the door locks will cycle once.

NOTE:
IF A SECOND KEY FOB REQUIRES PROGRAMMING, IT MUST BE PROGRAMMED WITHIN 1 MINUTE OF PROGRAMMING
THE FIRST FOB PROGRAMMING. PRESS ANY BUTTON ON THE SECOND FOB 3 TIMES TO PROGRAM ITS CODE. WHEN PROGRAMMING IS COMPLETE, THE DOOR LOCKS WILL CYCLE ONCE.

6. The programming mode finishes after the following:
a. Programming of two key FOBS is completed.
b. One minute has passed since programming.
c. Pin 1 of 16-way data link connector is removed from ground connection.
d. Ignition switch is turned on.
e. Any of the doors are opened.

Posted on Jun 25, 2009

  • 4044 Answers

SOURCE: 1999 chrysler 300m wont crank, code P0340

Sounds like the timing belt broke. Unfortunately this vehicle was not equiped with no contact valves so if that is the case you will need to have the engine and Head rebuilt. If the crank position sensor can't sense the position of the crank it should shutdown the electrical to keep you from damaging your engine.

Posted on Oct 09, 2009

  • 381 Answers

SOURCE: how do you remove the rear seat in a chrysler 300M

Grab the bottom seat cushion at the front of one side and pull it straight up then do the same on the other side. (you will have to pull up very hard) The bottom of the seat clips in. once you have the bottom out take the 2 bolts out of the seat belt fasteners that holds the bottom of the top seat cushion. Then pull straight up on the seat cushion to slide it off two tabs that hold the top.

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Chrysler 300M heater is blowing but no heat is coming out. Any ideas?


see if any one mess with it and did something that they should not have

Dec 28, 2010 | 1999 Chrysler 300M

1 Answer

My blinkers do not work on my 1999 chrysler 300m.


try replacing the flasher, the flasher must come from the dealer most aftermarket flasher wont work in chryslers, start with the flasher.

May 15, 2010 | 1999 Chrysler Sebring

1 Answer

I need to know where the fuse for the car lighter would be on a 1999 chrysler 300M


when you open the drivers2.gif door the fuse box is on the end of the dash there is a cover that you just pull on and it will come off and the fuse panel is in there. I'm not sure which fuse is for the lighter as i am in PA right now and my 300m is in Minnesota.

Oct 08, 2009 | 1999 Chrysler 300M

2 Answers

Elec


fuse 19 in the interior fuse box feeds those circuits...fuse I in the fuse box under the hood feeds fuse 19...i know you checked the fuses but did you check them for power

Jan 06, 2009 | 1999 Chrysler 300M

1 Answer

Chrysler heater wont turn off


sounds like the power module for the automatic tem control has gone bad and i hate to be the bearer of bad news but its not a cheap repair

Dec 31, 2008 | 1999 Chrysler 300M

1 Answer

Wont start


check for 12 volts at starter from battery, and make sure power and grounds are on well, remove starter and take to auto zone to test for free, then buy a chiltons if that doesnt work and trouble shoot it from the no start category, could be other sensors.

Sep 05, 2008 | 1999 Chrysler 300M

Not finding what you are looking for?
1999 Chrysler 300M Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...