Question about Cars & Trucks

Open Question

Dtc fault code p2096 on dodge ram 1500 5.7 hemi

Just want to locate wher this sencor is to fix it

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

dustyboner
  • 331 Answers

SOURCE: Diagnostic code P2299 for 2004 Dodge Ram 1500 5.7 hemi?

P2299-BRAKE PEDAL POSITION / ACCELERATOR PEDAL POSITION INCOMPATIBLE

Set Condition:
The PCM recognizes a brake application following the APPS showing a fixed pedal opening. Temporary or permanent. Internally the PCM will reduce throttle opening below driver demand. One trip fault and the code will be set within 5 seconds. ETC light will illuminate, the light will only stay illuminated while DTC is active.




Possible Causes

DRIVER PRESSING ACCELERATOR PEDAL, THEN PRESSING BRAKE PEDAL, AND CONTINUES TO HOLD THEM DOWN SIMULTANEOUSLY

STOP LAMP SWITCH

APP SENSOR


The most likely cause of this DTC is Brake Torquing the engine by pressing the Accelerator pedal and the pressing the Brake Pedal.

Posted on Jul 17, 2008

  • 66 Answers

SOURCE: Need diagram to install serpentine belt on 2004

There should be a diagram under the hood on the fan shroud or radiator support. If not, let me know and I see if I can find one. For the most part, if the pulleys it rides on are grooved, the belt ribs ride on it, it the pulley is smooth, the back side rides on it. From a picture of the alternator I have, from the passenger side coming up, over the alternator, then down and under the belt tensioner (smooth pulley), then up and over A/C compressor, then down and around P/S pump, up and around water pump, down around crankshaft pulley.

Posted on Jun 03, 2009

  • 249 Answers

SOURCE: replace timing chain on 03 dodge ram 1500 with 5.7 hemi

i have an 02 and i purchased a repair manual from autozone

Posted on Jan 05, 2010

  • 1796 Answers

SOURCE: I have a 2004 dodge ram 1500 with hemi 5.7. The

Hi!!
The O2 sensor for Bank 1 is located below left front of transmission, in exhaust. Check diag. below.
1kbron_41.gif

Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Posted on Dec 04, 2010

  • 1 Answer

SOURCE: 2007 dodge Ram 1500 hemi fuel cap sensor comes on

I just had the same problem, new cap, deleted the codes with a obd... took it to the dealership...
its the EGR valve that was bad on my truck 2007 dodge ram 45000 miles...
i get it back on friday, its a simple part 1 wire harness and 2 bolts and gasket.

Posted on Mar 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where fuel regulator is located on dodge ram 1500 hemi 5.7 2006


I believe it's part of the fuel pump in the tank.

Jan 23, 2015 | 2006 Dodge Ram 1500

1 Answer

What is code p1414 on Dodge ram hemi engine


ok code p1414 is a secondary air injection system monitor circuit high voltage air pump short, code p3400 is a faulty cylinder deactivation solenoid,it could be a fault in the harness or poor electrical connection

Jul 15, 2014 | 2005 Dodge Ram 1500

1 Answer

Looking for firing and coil order 2004 hemi 5.7


For ALL 2004 Dodge RAM (1500, 2500, and 3500) (2WD and 4WD) 5.7L V8 Hemi:

.........Firing Order:
Coil...1-8-4-3-6-5-7-2
Plug..6-5-7-2-1-8-4-3

This should have been located at the top of the your Intake Manifold.

Let me know if this helped...

Apr 15, 2010 | 1998 Dodge Ram 1500 4WD

1 Answer

2005 Ram 1500 4wd HEMI PO406 - EGR


Hey greenlee99, your best bet would be to grab one these manuals so that you have pictures and diagrams along with step by step instructions. It will tell you what tools and parts you need. Can't go wrong with having it.

Feb 15, 2010 | 2005 Dodge Ram 1500

1 Answer

Knock Sensor location on a 2004 Dodge ram 1500 5.7 hemi


2 knock sensors are used..small black plastic sensor bolted into engine block below each exhaust manifold..be careful not to over torque bolts upon installation

Feb 24, 2009 | 2003 Chrysler PT Cruiser

2 Answers

Stalls at idle


they needed to replace my IAC module. (Idle Air Control)
covered under warranty cost me 50.00 deductible Good luck

Aug 28, 2008 | 2004 Dodge Ram 1500

1 Answer

Diagnostic code P2299 for 2004 Dodge Ram 1500 5.7 hemi?


P2299-BRAKE PEDAL POSITION / ACCELERATOR PEDAL POSITION INCOMPATIBLE

Set Condition:
The PCM recognizes a brake application following the APPS showing a fixed pedal opening. Temporary or permanent. Internally the PCM will reduce throttle opening below driver demand. One trip fault and the code will be set within 5 seconds. ETC light will illuminate, the light will only stay illuminated while DTC is active.




Possible Causes

DRIVER PRESSING ACCELERATOR PEDAL, THEN PRESSING BRAKE PEDAL, AND CONTINUES TO HOLD THEM DOWN SIMULTANEOUSLY

STOP LAMP SWITCH

APP SENSOR


The most likely cause of this DTC is Brake Torquing the engine by pressing the Accelerator pedal and the pressing the Brake Pedal.

Jul 17, 2008 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

178 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...