Question about 2011 Ford Edge

Open Question

How to remove rear liftgate trim panels 2011 edge

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 72 Answers

SOURCE: Need to remove interior panel of Ford Windstar liftgate

Get a trim panel removal tool at an autoparts store. It's a thin metal piece that slides between the panel and framework where the plastic clips hold the panel on. Slide it in at each clip....and pop each one off. There may be some trim screws also.

Posted on May 27, 2009

Ad
motor1258
  • 6674 Answers

SOURCE: rear hatch will not open,how is the interior trim

look for any plugs that may be covering screws around outside edge, as well as obvious screws, then the rest will probably be push/pull clips. Usually a quick **** will release them.

Posted on Feb 20, 2010

leedavidian
  • 1420 Answers

SOURCE: How to remove the right rear passenger door

Welcome to FIxYa.com



REAR DOOR TRIM PANEL

Rein oval and Installation

1. Remove the rear door trim panel assist handle cover.

2. Remove the rear door trim panel assist handle screws.

3. Remove the rear door trim panel handle bezel cover.

4. Remove the rear door trim panel handle bezel screws.

5. Remove the rear door trim panel lower screw.

6. CAUTION: To avoid damaging the trim panel, do not pull the bottom of the panel

outward.

Remove the rear door trim panel by lifting upward on the armrest to disengage the

panel clips.

7. Disconnect the electrical connectors.

8. To install, reverse the removal procedure.


leedavidian_78.jpg



Thank you for using FixYa.com

Regards, Lee Davidian

Posted on Dec 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a burned out rear backup light


Open the liftgate. Remove the liftgate applique. Refer to Liftgate Applique Replacement in Body Rear End. Remove the back up lamp socket (1) from the liftgate applique by turning the socket (1) counterclockwise. Remove the back up lamp bulb from the socket.
Lift gate Applique Replacement
Remove the lift gate trim panel. Refer to Lift gate Trim Panel Replacement .
1
Lift gate Applique Nuts (Qty: 5)
Tip
Disconnect the electrical connector.
Tighten
10 N?·m (89 lb in)
2
Lift gate Applique

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

May 10, 2016 | 2004 Cadillac SRX

1 Answer

How do i replace the park assist module in a 2011 chevy traverse???/


Have you checked the fuse? If so, the module is located behind the left rear trim panel. Remove the panel to access. Below is a diagram of the trim panel and location of the module in BLUE>
Preliminary Procedures
  1. Move the rear seat to the full forward position.
  2. Remove the rear number?2 seat . Refer to 3rd Row Seat Removal and Installation.
  3. Remove the rear quarter upper trim panel. Refer to Quarter Upper Trim Panel Replacement.
  4. Disconnect the liftgate actuator rod from the liftgate. Refer to Liftgate Actuator Rod Replacement.
  5. Disconnect the rear seat number 2 shoulder belt anchor bolt. Refer to Rear Seat Number 2 Retractor Side Belt Replacement.
  6. Remove the liftgate door sill plate. Refer to Liftgate Door Sill Plate Replacement.



woauitf41mzpgaaaabjru5erkjggg==

Nov 16, 2014 | 2011 Chevrolet Traverse

1 Answer

Need to put passenger miror on. i need help to show me how to take the door panel off.


Section 01-05: Trim, Interior 1998 Windstar Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/22/1999 Trim Panel, Door Front
Removal
  1. Remove door latch cover by prying from top edge and pulling trim free of retaining clips and sliding trim away from latch.
  1. Remove portion of armrest containing door lock switch and window regulator control switch (14529) by pulling straight up.
  1. Remove rear view outside mirror mounting hole cover assembly by prying at top and pulling upward to release double-sided clip.


    Trim Panel


    ar0885a.gif


    Item Part Number Description 1 23942 Front Door Trim Panel 2 56908-S58 Screw (1 Req'd), Right Door 56906-S58 Screw (1 Req'd), Left Door 3 18B978 Radio Speaker Grille Name Plate 4 56911-S58 Screw (1 Req'd) 5 17D720 Cover Assembly Rear View Outside Mirror Mounting Hole
  1. Remove screw attaching front door trim panel (23942) to front door (20124) under switch plate.
  1. Remove two screws located at bottom of front door trim panel.
  1. Disconnect the door lock switch (14028) and window regulator control switch electrical connectors.
  1. Remove door window regulator handle if equipped by unsnapping and pivoting away the handle cover from base to expose retaining screw. Remove screw from the door window regulator handle.
  1. Pull front door trim panel from the top to release hooks from front door .
  1. Remove front door trim panel.
Installation
  1. Replace any bent or damaged fasteners.
  1. Follow removal procedure in reverse order.
Body Side
Removal
  1. Remove door handle retaining clip by sliding a shop towel between handle and door trim. With tension on the cloth, pull one end of the cloth so it slides between the handle and the door trim. If handle does not come out, reverse direction.
  1. Unfasten 13 christmas tree fasteners using double-acting spring-loaded trim removal tool and pull body side trim panel from body side door.
  1. Remove forward and rearward mating sections from under window trim.
Installation
  1. Replace all christmas tree fasteners.
  1. Follow removal procedure in reverse order.
  1. For installation of handle, install clip to handle, then push handle onto shaft to snap in place.


    r11176a.gif

Back
Removal
  1. Disconnect rear window defroster wires.
  1. Remove the liftgate window garnish moulding as described.
  1. Remove screws attaching liftgate handle to liftgate and liftgate inside trim panel.
  1. Using Rotunda Windshield and Moulding Trim Removal Kit 107-R0401 or equivalent, pry pushpins retaining liftgate trim from the liftgate.
  1. Remove liftgate trim.
Installation
  1. Follow removal procedure in reverse order.


    Liftgate


    r10441a.gif

2010&c18=modelyear&c35=wsm%2ctrim%20panel%2c%20door%2csww%2c01-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1998 Ford Windstar

1 Answer

How to remove interior panel from tailgate?


Remove the liftgate pull handle. Refer to Liftgate Inside Pull Handle Replacement .
DO NOT attempt to remove the liftgate trim panel if there is a failure of the electric latch. Refer to Opening the Liftgate Without Electrical Power .
1
Liftgate Trim Finish Panel
2
Liftgate Trim Finish Retainer Clips (Qty: 2)
3
Liftgate Lower Trim Finish Panel
4
Liftgate Trim Finish Retainer Clips (Qty: 14)
mrtechwrench_6.gif

Nov 22, 2010 | 2009 Chevrolet HHR

1 Answer

Replace a brake light


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif

Nov 04, 2010 | 1998 Saturn SL

1 Answer

I need to replace rear tail light bulbs on 1996 Saturn SL1


COUPE The side marker lights for the SC and SC2 are part of the turn signal/parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. Rear Turn Signal, Brake and Parking Lights EXCEPT WAGON
  1. Disconnect the negative battery cable. Fig. 5: Remove the trim panel fasteners - except wagon 84196109.jpg
    Fig. 6: Carefully remove the trim panel - except wagon 84196110.jpg
    Fig. 7: Pull the lamp assembly straight back and out of the opening 84196111.jpg

  2. Remove the trim panel fasteners, then carefully remove the trim panel.
  3. Remove the 2 retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  4. Tilt the assembly downward for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  5. Installation is the reverse of removal. Fig. 8: Tilt the assembly downward for access to the sockets 84196112.jpg
    Fig. 9: Twist and remove the socket and bulb from the lamp assembly 84196113.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Remove the retaining screws from the side of the lamp assembly, then pull the lamp assembly straight back and out of the opening.
  3. Tilt the assembly for access to the sockets, then twist and remove the socket(s) from the lamp assembly. Replace the bulb(s), as necessary.
  4. Installation is the reverse of removal. Fig. 10: Exploded view of the tail lamp assembly - wagon 84196114.gif
High-Mount Brake Light EXCEPT WAGON
  1. Disconnect the negative battery cable.
  2. Open the trunk for access to the lamps.
  3. Locate the bulbs at the rear underside of the trunk lid. Remove the bulb(s) by twisting, then pulling straight out.
  4. Installation is the reverse of the removal. Fig. 11: Remove the high-mount brake light by twisting its socket 1?4 turn counterclockwise - except wagon 84196115.jpg
WAGON
  1. Disconnect the negative battery cable.
  2. Raise the liftgate, then remove the wedge blocks from each side of the liftgate assembly.
  3. Remove the lower fasteners from the liftgate lower trim panel, by pushing in the center of each pin approximately 1?8 in. until it clicks, then remove the fastener.
  4. Insert a screwdriver or small prybar into the hole in the lower trim panel (located near the wiper pivot on the pivot hump) so that the tool sits on top of the pivot. Lift up on the tool handle to disengage the trim panel upper clips, then remove the lower trim panel from the vehicle.
  5. Unplug the high-mount brake light wiring harness.
  6. Remove the brake light fasteners, then remove the lamp assembly from the liftgate.
  7. To remove the bulb(s), push slightly on the top edge of the lens and rotate it away from the housing. Remove the bulb(s) from the housing. To install:
  8. In order to prevent the possibility of water leaks into the liftgate, inspect the lamp gasket for damage and replace, if necessary.
  9. If removed, install the bulb(s) by inserting the bottom edge of the lens into the housing and snapping it into place.
  10. Position the lamp into the liftgate and tighten the fasteners to 35 inch lbs. (4 Nm).
  11. Connect the wiring harness to the lamp assembly.
  12. Align the upper clips on the lower trim panel to the liftgate slots, then install the panel by pushing at the clip locations.
  13. Reset the trim panel push-in fasteners by spreading the center pin tabs and moving the pin so that it sits approximately 1?4 in. out of the fastener. Insert the fasteners into the bottom of the trim panel and push the center pin until flush.
  14. Install the liftgate wedge blocks.
  15. Connect the negative battery cable and check for proper lamp operation. Fig. 12: Removing the liftgate lower trim panel assembly - wagon 84196116.gif
    Fig. 13: Exploded view of the high-mount brake light bulb and lens assembly - wagon 84196117.gif
Reverse Light EXCEPT 1991-96 COUPE For the Saturn wagons and sedans, the reverse lamp is part of the rear turn signal, brake and parking light assembly. Refer to the procedure in this section for lamp removal and bulb replacement. 1991-96 COUPE
  1. Disconnect the negative battery cable.
  2. Reach behind the bumper bar and disconnect the harness and socket from the reverse lamp. Remove the bulb from the socket.
  3. If necessary, unfasten the retaining nuts and remove the lamp from the bumper bar.
  4. Installation is the reverse of the removal. Fig. 14: Exploded view of the reverse lamp mounting - 1991-96 coupe 84196118.gif

Oct 23, 2010 | 1996 Saturn SL

1 Answer

Do I remove the entire cover or the little door thats atached to this cover on the passenger side? There are 3 brake lights that were recommended to replace. Driver side and passenger side plus the third...


Lamp, Rear Hi-Mount Lamp Assembly
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Raise the liftgate.
  1. Remove the liftgate door trim panel (46404) . Refer to Section 01-05 for the removal procedure.
Trim Panel, Liftgate Door Removal
  1. Disconnect thebattery ground cable (14301) .
  1. On vehicles with a rear window wiper, remove the three rear wiper motor cover screws and remove the rear wiper motor cover.
  1. Pry the liftgate door trim panel (46404) away from the liftgate.
  1. Disconnect the luggage compartment lamp electrical connector.

    n11098a.gif

  1. Remove the liftgate door trim panel
  1. Rotate the rear hi-mount lamp socket counterclockwise and remove it from the rear hi-mount lamp (13A613) .

    k20521a.gif

  1. Remove the two rear hi-mount lamp housing nuts and remove the rear hi-mount lamp lens and housing.

    k20523a.gif

Oct 18, 2010 | 1995 Ford Aspire

1 Answer

I need to know how to remove the pannel cover on the rear hatch door I can get to the rear wipper motor


449b69b.jpg

Exploded view of the Explorer/Mountaineer rear liftgate trim panel (click for zoom)



Rear Window Wiper Motor


b5927f1.jpg

Fig. : Rear wiper motor assembly and related components

  1. Disconnect the negative battery cable.
  2. Remove the wiper arm and blade.
  3. Remove the liftgate interior trim.
  4. Remove the motor attaching bolts (3). Disconnect the electrical leads.
  5. Remove the wiper motor from the vehicle.
To install:
  1. Install the wiper motor in position and connect the electrical leads.
  2. Install the liftgate trim. Connect the negative battery cable.

I hope helps (remember to rate this).

Oct 11, 2010 | 1996 Ford Explorer

1 Answer

My 2001 Town and Country's rear windshield wiper motor is kaput. How do I change it without destroying the rear tailgate paneling


Pretty straight forward.....here are the steps:

Please don't forget to rate--

Rear Window Wiper Motor Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the rear wiper arm.
  3. Open the liftgate.
  4. Perform the following to remove the liftgate trim panel.
    • If equipped, remove the lift motor link
    • Remove the upper frame molding
    • Remove assist handle screws
    • Disengage the hidden clips around perimeter of liftgate trim
    • Disconnect the electrical connectors.
  5. Disconnect the wire connector from the wiper motor.
  6. Remove the wiper motor mounting screws.
  7. Remove the wiper motor.
To Install:
  1. Position the wiper motor in the liftgate.
  2. Install the wiper motor mounting screws.
  3. Connect the wiring connector.
  4. Install the liftgate trim panel.
  5. Close the liftgate.

Jul 24, 2009 | 2001 Chrysler Town & Country

1 Answer

I have a 1998 Ford Explorer.


  1. Remove the rear pivot arm; refer to Pivot Arm—Rear . 7981ec7.gif
  2. Remove rear pivot arm.
    1. Lift the pivot arm nut cover.
    1. Remove the nut.
    1. Remove the pivot arm.
  1. Remove the liftgate door trim panel; refer to Section 501-05 . Remove the (A) liftgate handle to liftgate screws and the (B) liftgate handle. Remove the liftgate trim panel screw access plug. Remove the screw.
  2. Remove the liftgate door trim panel.
    1. Use Windshield and Molding/Trim Removal Kit to remove the liftgate door trim panel from the liftgate window opening.
    1. Push the liftgate door trim panel toward the top of the liftgate and remove the liftgate trim panel. 9e75e00.gif
  1. Position the watershield aside to gain access to the rear wiper motor.
  1. Remove rear wiper motor.
    • Disconnect electrical connector.
    • Remove three retaining bolts.
    • Remove rear wiper motor.
good luck.

Jan 10, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
2011 Ford Edge Logo

Related Topics:

558 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...