Question about Cars & Trucks

1 Answer

My sons mazda mx6 clutch pedal when pushed to the floor stays there we just put a new slave cylander in

After putting the slave cylinder in the problem still occurs when purchasing the new slave cylinder it did not come with a new piston I tried 3 different ones and still know piston we used the ols on don't know where to get a new piston

Posted by on

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 14,384 Answers

This one has one.

Posted on Jan 20, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: clutch has no pressure and i have replaced everything i know of.

did u try bleeding the lines ? if your changed every thing and still have nothing u might just have alot of air in the system

Posted on Dec 16, 2008

  • 1118 Answers

SOURCE: Is it a bad Slave Cylinder or a Master Cylinder on my 95 F-150

did you try to take line off at slave cyl. and see if fluid comes from resavor? also take bleeder out and see if holes are pluged up in bleeder. if all this chks. out ok than its got to be slave cyl. they have been known to go bad. just that quick too.

Posted on Jan 26, 2009

  • 496 Answers

SOURCE: clutch pedal stays on floor when released

check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Posted on Feb 22, 2009

  • 2 Answers

SOURCE: Clutch has no resistance, stays near floor after applying pressur

I had this same problem on my last 91 accord. You most likely have air in the line. I had to bleed the line for the master cylinder, and then refill the clutch popped up right off the floor. As long as it is not continuious then I would try this. All I needed was a wrench. and i didnt cost me anything. Hope this helps, if you buy the book it will show you how to do it, just look under clutch it will show you how to bleed it. Good Luck.

Posted on Mar 17, 2009

  • 6 Answers

SOURCE: stuck clutch pedal on a Mazda B series truck

Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Posted on Dec 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 Mazda MX6 Clutch pedal has no push back from floor but still shifts


I am not a mazda guy but it sounds like the pressure plate is bad. Have you check the clutch linkage to be sure something did not slip or break. If so I would be looking at the clutch pressure plate.

May 18, 2017 | Mazda Cars & Trucks

1 Answer

2000 Camry clutch


Check the fluid in your slave cylinder. you have a master cylinder for the brakes and a slave cylinder for the clutch. It should have a screw on lid and if it's full, you probably need a new one.

Sep 27, 2017 | Cars & Trucks

1 Answer

1993 mazda mx6 car was fine has new clutch pushed clutch in stay on floor started pumping it gain compression. Then after a while will loose compression again?


If the shop that installed the clutch also replaced the hydraulic system, I would take it back to them.
If they only replaced the clutch disc and cover, the master cylinder or slave cylinder may have failed.

Feb 04, 2013 | Cars & Trucks

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

1 Answer

My clutch dropped to the floor replaced the slave cylinder and bled it.. Still nothing. i need to know what to do next or maybe the correct process of bleeding


I do not know what brand you are working on. Some have bleeders, some do not. If it has a bleeder fill the Clutch Master Cylinder with brake fluid and have someone push and hold the clutch pedal. Put your safety glasses on and crawl under and crack the bleeder. Air will bubble out of the bleeder and the clutch pedal will go to the floor. HOLD THE PEDAL ON THE FLOOR until you close the bleeder. Do it again and again until no more air comes out. The procedure if there is no bleeder is the same except you must loosen and tighten the line itself. The clutch should work if the slave cylinder was the problem to begin with. The Clutch Master Cylinder can be shot and not producing any pressure. The throw out bearing can destroy the clutch fingers and push right through them. If that is what happened the slave cylinder will push the clutch fork just like it should but nothing will happen.

Jun 10, 2010 | Cars & Trucks

2 Answers

My clutch pedal is stuck to the floor??


It is most likely a hydraulic clutch, and it is most likely leaking at the clutch slave cylinder. Check the clutch master cylinder for fluid, it should be a small master cylinder looking thing with a fill cap next to the brake master cylinder and booster unit. If it is empty fill it with the same dot 3 brake fluid that you use for your brake master cylinder, and make sure that you are pouring the fluid into the clutch master cylinder reservoir and not the rubber seal that should be under the fill cap. After filling the clutch master cylinder up with fluid, then try and pump up the clutch pedal. It might take a while to pump up hydraulic pressure, and you might also have to work the pedal a few times by hand at first.

Also, you might have to bleed the clutch at the slave cylinder if it will not build up enough pressure to release the clutch.

Apr 28, 2010 | 1988 Mazda RX-7

1 Answer

My cluch keeps stiking to the floor in my 1989 mazda mx6


check all mechanical parts of clutch pedal make sure there is no catching or draging in its joint lube if possible also check the spring that pulls the clutch pedal back up make sure not damaged or worn out, A different problem may be in your hydrolic clutch system, such as a bad slave cylinder or your system may just need bleeding, if you have a problem with your hydrolics when the clutch goes to the floor and stays you will not be able to disengage your clutch as well until you pull the clucth back up and pump it a few times.

Apr 03, 2010 | 1989 Mazda MX-6

1 Answer

Clutch pedal stuck up


You have to replace the Slave Cyl. when you put on the new one you have to bleed it ..To get the air out of the new line.

Mar 10, 2010 | Hyundai Motor 2002 Elantra

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

1 Answer

Clutch pedal stays on floor when released


check the helper spring on the clutch pedal. You'll have to get down in the driver's footwell and using a flashlight look at the mechanism while you push the pedal down (and pull up). If the spring isn't missing or broken and everything looks okay, then change the clutch master cylinder. The piston in the cylinder is probably binding due to corrosion in the bore. I have an 1986 and had the same problem. Changing the clutch master cylinder fixed it.

Feb 21, 2009 | 1985 Toyota Celica Supra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...