Question about 1988 Nissan Pulsar

1 Answer

90 nissan sentra engine and trans swap to a 88 pulsar

Will it work?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

Yep they will interchange

Posted on Jan 26, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

88 Nissan sentra getting 12-15mpg. I'm at a loss


If the car doesn't sound funny or run rough you probably have a bad oxygen sensor. Ask a parts store for a replacement, it will be located on your exhaust pipe near the engine. It is a very simple part to replace, just unscrews like a spark plug and has a wire harness.

Jun 08, 2011 | 1988 Nissan Sentra 2 Door

2 Answers

I was driving my 90 nissan sentra and. It started to rev up it doesn't want to shift u can drive bout 25 mph I think its stuck in 1st gear


it actually sounds as if the high clutches in trans is slipping you have to have a pressure test done but be prepared to replace trans

Jan 15, 2011 | 1990 Nissan Sentra

1 Answer

I have a 1988 Nissan Sentra with a 1.6 l ...well it threw a rod and i purchaced a replacement motor from a salvage yard. They tell me its for a '88 but this motor used a timing chain insted of a timing...


there are 2 different 1.6L engines for this year. If you can find the right flywheel, you'll probably be fine. Other possible issues might be with wiring, but I checked the wiring diagram and it makes no distinction between the 2 engines. Still, I would check the connectors and make sure all the electric work will fit. Hopefully the computer will not object to the engine...

Oct 11, 2010 | 1988 Nissan Sentra 2 Door

1 Answer

Nissan pulsar '88. replaced starter motor, then


Is it a manual, or an automatic? Earlier Nissans sometimes have a problem with the neutral safety switch (a device that keeps the engine from rolling over in gear or without the clutch depressed.) Generally, if their bad, they need to be a little warm before they'll start, like setting in the sunlight for a few hours.

Good Luck!

May 22, 2010 | 1988 Nissan Pulsar

1 Answer

Need tappet clearance settings for 88 nissan sentra 1.6 b12


both engines on these sentras are hydraulic and no adjustment is necessary. if youre getting some tapping noise, try a good engine flush and idle till the noise goes away. the last time i did one of these, it took 2 hours for the noise to cease. drain the oil and use a nissan oil filter and probably 10w 40 oil. you should be fine. cheap fix huh?

Feb 22, 2010 | 1988 Nissan Sentra 2 Door

2 Answers

Alternator


1996 Nissan/Datsun Sentra 1.6L SFI DOHC 4cyl

Nissan Sentra/Pulsar/NX 1982-1996 Repair Guide
The alternators for Pulsar and Sentra have not changed much over the years. However, the 1987-88 alternators for Pulsar and Sentra have a different internal diode assembly.
  1. Disconnect the negative battery terminal.
  2. Disconnect the 2 lead wires and connector from the alternator.
  3. Loosen the drive belt adjusting bolt and remove the belt.
  4. Unscrew the alternator attaching bolts and remove the alternator from the vehicle.
To install:
  1. Install the alternator and retaining bolts loosely.
  2. Install the belt and connect the wiring.
  3. Adjust the belt as outlined in . Torque the retaining bolts to 25 ft. lbs. (34 Nm).

I hope help you with this (rated this help).

Sep 11, 2009 | 1996 Nissan Sentra

1 Answer

Do you have to remove trans when you replace the engine


The engine and the transmission is bolted together, it is always better to remove them at the same time, it is easier to seperate the transmission from the engine when they are both out of the vehicle.

Nov 16, 2008 | 1988 Nissan Pulsar

1 Answer

2007 Nissan Sentra Problem


Possible ground issues. Any check engine light?

Jul 07, 2008 | 2007 Nissan Sentra 2.0 SL Sedan

2 Answers

Nissan Sentra jerks in 3rd and 4th


have you ever done trans flush??/powerflush??it will flush EVERYTHING. dump and fill only get's so much. how is the fluid in the trans??is the check engine light on??

Jun 16, 2008 | 2002 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...