Question about 2009 Dodge Journey

Open Question

2009 dodge journey door lock wont work

I put my key in because my automatic door unlock wont work and the key wont unlock the door

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 137 Answers

SOURCE: 1999 DODGE DURANGO AUTOMATIC DOOR LOCKS.

That feature is called rolling locks.
In order to program the rolling door locks you will need to do the following procedure (listed on page 10 of the owners manual).
1. Close all of the doors.
2. Place the key in the ignition and cycle the key from the OFF to the ON position for a total of 4 to 5 times, ending in the ON position, do not start the engine.
3. Press the driver's side power lock switch to LOCK the doors within 30 seconds of cycling the key.
4. You will hear a single chime when programming is complete.
5. To cycle the feature on/off repeat the procedure.

Posted on Jan 11, 2009

motor1258
  • 6674 Answers

SOURCE: Door locks dont work

2 things I would try before replacing an expensive BCM. Disconnect your battery for 5 minutes or so, then reconnect, and see if that helped at all. I have heard in some cases it worked successfully. If that doesn't cure it, I would go to the plug on the BCM itself, (with battery disconnected) and pull the plug off, inspect it, and clean it & mating pins on BCM very thoroughly with contact cleaner or similar electrical cleaner. Add a little di-electric grease to connection & put it back together nice & tight & see what happens. The BCM is usually located on passenger side in kick panel area,(by right foot when sitting) either behind kick panel or above it.

Posted on Mar 15, 2009

  • 66 Answers

SOURCE: 2004 Dodge Ram 1500 Quad Cab Drivers side power door lock broken

Sounds like the link rod to the latch are jammed in the locked position by something inside the door or it came off. Any way, you have to remove the door panel to get access to it.

Posted on Jun 03, 2009

  • 109 Answers

SOURCE: key lock on drivers door won't unlock the door

you need to take the door panel off, there is a rod in there that connects to the lock cylinder it frequently pops off, there is a little plastic clip that should hold it on to the cylinder it may be broken!!

Posted on Jun 26, 2009

  • 159 Answers

SOURCE: my driver side rear door

Could be very simple. Remove inside door panel & check for disconnected wire to solenoid. If okay--check where wires enter the door for broken or corroded wire & repair.

Posted on Mar 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do unlock doors with dead battery on a 2010 dodge journey....little key in fob will turn but won't unlock...help


Will the work on trunk? I wonder if key has been changed out. When power goes out in my SUV doors still open. Only other way I know is to jimmy the lock with coat hanger or something.

Jan 27, 2015 | 2010 Dodge Journey SXT

1 Answer

Can I program a keyfob for a 2009 Dodge Journey using 2 transponder chip keys?


The dealer will ned to use the diagnostic scanner to program just one fob. If you you have two good ones then you can do a third or fourth.

Sep 09, 2014 | 2009 Dodge Journey SXT

1 Answer

My doors keep unlocking themself even after i lock it remotey or manuel?


a. When you lock the doors (with the Switch) with you inside... do they stay locked?
b. Do your Doors lock automatically when you put it in gear?

Have you tried using a Different FOB (Remote). If one Remote works properly and One Unlocks the Doors after locking... you have a Defective (FOB) Remote

Apr 04, 2013 | 2009 Dodge Charger SE

1 Answer

Driver side door panel not working 2009 dodge journey


mine does the same.. disconnect the battery.. then reconnect.... works everyime! ive had to do it 3 times in 2 yers

Jun 10, 2012 | 2009 Dodge Journey

2 Answers

Journey wont start sometimes


Do you have a factory alarm put the key in is there something stating anti theft and when you crank it does it go out if not anti theft may be active.

Apr 21, 2011 | 2009 Dodge Journey

1 Answer

Remote starter


They hooked up the wrong wire it should be hooked up to the lock wire, you need to press the lock button in order for it to start

Sep 11, 2009 | 2009 Dodge Journey

Not finding what you are looking for?
2009 Dodge Journey Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...