Question about Chevrolet Corsica

1 Answer

1990 corsica cuts out after 15 minute then will not restart after 2 hours

Already check vac leaks, replaced thermostat sensor, oxygen sensor, ECM sensor, air filter, cadilatic converter,

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,103 Answers

Sounds like an overheated ignition chip or pickup and maybe the computer..change the chip and pickup first they are less expensive to replace.. then find a computer at a towyard to replace yours(they can match the car type at the office of the towyard using the computer there..good luck..

Posted on Jan 20, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fixincars
  • 335 Answers

SOURCE: Sonata stalls after running good for 10 minutes.

Ignition Control module, and crank position sensors, they get hot and fail and after brief cooling period they work again

www.aceautomotive1.com

if this information was helpful please give me a good rating Thank you,Randy

Posted on Aug 17, 2008

cognac222
  • 4 Answers

SOURCE: 89 Corsica: no power, hesitates in drive, idles

Check your fuel pressure, and or injectors. You may have too much fuel getting into the engine causing it to burn rich and overheat the converters.

Posted on Apr 26, 2009

nattsss
  • 119 Answers

SOURCE: catalytic converter or oxygen sensors?

i would replace the oxygen sensor first as it is the cheapest and easiest

Posted on Nov 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Looking for what a code P0170 could mean for a 2002 gmc envoy ? I already replaced map sensor and still continue to have the same problem


For this code, you need to look at live data on the scanner. Add upstream O2 sensor data for bank 1 to the scanner display and start the engine. P0170 indicates bank one is out of range. Does bank one read higher or lower than normal? Normal is around 0.5 volts. If higher, you are too rich. If lower, you are too lean. If too rich, you may have a leaky injector. If lean, you may have a vacuum leak or dirty injectors.

Aug 19, 2017 | GMC Cars & Trucks

1 Answer

Po136-o137 says change 02 sensor on bank 1 sensor2 I did but engine light is still on 2004 chevy tahoe


code p 0136 refers to heated oxygen sensor (HO2S) 2 bank 1 ---circuit malfunction===causes ---heating inoperative ---wiring---HO2S--- ECM
also refers to oxygen sensor (O2S0 2 bank 1---circuit malfunction===causes --- wiring---O2S ---ecm
it also refers to heated oxygen sensor (HO2S) 2 bank 1 ---no signal===causes ---wiring --- HO2S---
code p 0137 refers to HO2S 2 bank 1 ---low voltage -===causes --exhaust leak---wiring short to ground ---HO2S--- ECM
it also refers to O2S 2 bank 1---low voltage ===causes exhaust leak---wiring short to ground ---O2S ---ECM
to set you up here-- there are 4 oxygen sensors in the system
2 are heated oxygen sensors (HO2S) on in each exhaust manifold or exhaust pipe before the cat converter and
2 oxygen sensors (O2S) -- one in each exhaust pipe after the cat converters
heated oxygen sensors have 4 wires and O2S sensors normally only 2 wires
it is more that possible that you changed the wrong sensors and in the process damaged the delicate wires with the incorrect spanner being used

Jul 25, 2016 | 2004 Chevrolet Tahoe

1 Answer

How to fix error code P0153 Slow Response Bank 2 Sensor


This involves the oxygen sensor upstream the catalytic converter on Bank 2. This code indicates the engine air fuel ratio is not being adjusted by the oxygen sensor signal or the ECM as expected to do so, or not adjusted as often as expected to do so once the engine is warmed or under normal engine use. You will likely not notice any drive ability problems, although there may be symptoms. A code P0153 may mean that one or more of the following has happened: The oxygen sensor is faulty The wiring to the sensor is broken / frayed There is an exhaust leak Possible Solutions Things that may fix the problem include: Check and fix any exhaust leaks, Check for wiring problems (shorted, frayed wires), Check the frequency and amplitude of the oxygen sensor (advanced), Check for a deteriorating / contaminated oxygen sensor, replace if necessary, Check for inlet air leaks, Check the MAF sensor (sensor of the pipe from air cleaner) for proper operation, Replace the Bank 2 oxygen sensor upstream of the catalytic converter (follow from CC towards engine - you wil see the sensor)

Aug 18, 2014 | 1999 Isuzu Rodeo

1 Answer

I have code p0137 coming up on my 2003 jeep grand cherokee laredo what does the code mean?


P0137 - Oxygen O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2)

Essentially the same as P0136, P0137 refers to the second oxygen sensor on Bank 1. P0137 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This, is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 1 Sensor 2 is located to the rear of the catalytic converter and should produce an output signal relative to oxygen storage capacity of the catalytic converter. This rear (sensor 2) sensor is less active than the signal produced by the front sensor. However, if the ECM senses the sensor is inactive, this code will set.

Symptoms: There may be no visible symptoms to the driver, other than the MIL (Check Engine / Service Engine Soon) illumination.

Causes: A code P0137 may mean that one or more of the following has happened:
* Faulty o2 sensor Exhaust leak near the rear sensor
* Plugged catalyst
* Short to voltage on O2 signal circuit
* High resistance or open on O2 signal circuit

Possible Solutions:
* Replace faulty sensor
* Repair exhaust leak near the rear sensor
* Check for restriction in catalyst and replace as necessary
* Repair short, open, or high resistance on o2 signal circuit

Hpe hti shelps (remember comment and rated this).

Jul 26, 2010 | 2003 Jeep Grand Cherokee

1 Answer

Po137/po157 codes no activity


P0137 / P0157-Oxygen O2 Sensor Circuit Low Voltage (Bank 1, Sensor 2) refers to the second oxygen sensor on Bank 1. P0137 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This, is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 1 Sensor 2 is located to the rear of the catalytic converter and should produce an output signal relative to oxygen storage capacity of the catalytic converter. This rear (sensor 2) sensor is less active than the signal produced by the front sensor. However, if the ECM senses the sensor is inactive, this code will set.

A code P0137 may mean that one or more of the following has happened:

Faulty o2 sensor Exhaust leak near the rear sensor
Plugged catalyst
Short to voltage on O2 signal circuit
High resistance or open on O2 signal circuit

Possible Solutions…
Replace faulty sensor
Repair exhaust leak near the rear sensor
Check for restriction in catalyst and replace as necessary
Repair short, open, or high resistance on o2 signal circuit

Mar 08, 2010 | 2000 Chevrolet Camaro

1 Answer

I just get a 2000 lanos but the check engine ligth is ON when i put it the code reader says to me 2 codes : 1st code is P0137 and p1336 say a lot lf items but got to be only one of those , whath can be???...


Essentially the same as P0136, P0137 refers to the second oxygen sensor on Bank 1. P0137 means the O2 oxygen sensor's voltage remained low for longer than 2 minutes. This, is interpreted by the ECM as a low voltage condition and sets the MIL. Bank 1 Sensor 2 is located to the rear of the catalytic converter and should produce an output signal relative to oxygen storage capacity of the catalytic converter. This rear (sensor 2) sensor is less active than the signal produced by the front sensor. However, if the ECM senses the sensor is inactive, this code will set.

Symptoms There may be no visible symptoms to the driver, other than the MIL (Check Engine / Service Engine Soon) illumination.

Causes
A code P0137 may mean that one or more of the following has happened:
  • Faulty O2 sensor Exhaust leak near the rear sensor
  • Plugged catalyst
  • Short to voltage on O2 signal circuit
  • High resistance or open on O2 signal circuit

  • Possible Solutions
  • Replace faulty sensor
  • Repair exhaust leak near the rear sensor
  • Check for restriction in catalyst and replace as necessary
  • Repair short, open, or high resistance on o2 signal circuit
The other code is your crankshaft position sensor. You need to replace both of the sensors and the check engine light will go off.

Sep 28, 2009 | 1999 Daewoo Lanos

1 Answer

Will not restart after being off for 15 mins.


try a back pressure test. or disconnect exhaust BEFORE catalitc converter and see if it runs longer then... if it runs better catalitch converter needs to be replaced.

Jun 13, 2009 | 1991 Buick Century

1 Answer

2001 Nissan Maxima service engine light stays on code from Auto Zone scanner is PO139 and PO138. What should my next step be to solve this problem.


code p 0138 refers to 2 items
1--heated oxygen sensor(HO2S) 2 bank 1--high voltage ==causes --wiring short to positive --HO2S---ECM
2--oxygen sensor (O2S) 2 bank 1--high voltage ===causes wiring short to positive ---ECM
code p 0139 refers to 2 items
1--- heated oxygen sensor (HO2S) 2 bank 1--slow response ===causes --heating inoperative --wiring--ECM
2--oxygen sensor (o2S) 2 bank 1 slow response ===causes --wiring --- O2S

heated oxygen sensors9HO2S) are in the exhaust manifold before the cat converter
Oxygen sensors (O2S) are after the cat converter
it is indicated that the HO2S is faulty-
check the wiring and /or replace both sensors

Nov 16, 2017 | 2001 Nissan Maxima

2 Answers

98 mercury villager OBD I code P0135


This code refers to the front oxygen sensor on Bank 1. The heated circuit in the oxygen sensor decreases time needed to enter closed loop. As the O2 heater reaches operating temperature, the oxygen sensor responds by switching according to oxygen content of the exhaust surrounding it. The ECM tracks how long it takes for the oxygen sensor to begin switching. It the ECM determines (based on coolant temp) that too much time elapsed before the oxygen sensor began operating properly, it will set P0135.
Repair short or open or high resistance in wiring harness or harness connectors.
Since you have already changed out your O2 sensor (as long as you used to OEM replacement and not the "Universal" replacement) you should not have to replace it again. You might check your thermostat to part of the time it takes for the O2 sensor to start switching being based on coolant temp, if your thermostat is not operating properly, it could cause the coolant temp to take longer than what is considered by the ECM to be normal.

Feb 22, 2009 | 1998 Mercury Villager

1 Answer

Xterra repair


Since this is an intermittent problem, first try to determine if the problem arises due to one of these many intermittent problems:

* Vehicle vibration
* Heat sensitive
* Freezing
* Water intrusion
* Electrical load
* Cold or hot start up

If you can't isolate the cause of the intermittent problem, you can try adjusting the Idle Speed/Ignition Timing/Idle Mixture Ratio:

Idle Speed/Ignition Timing/Idle Mixture Ratio Adjustment

PREPARATION
1) Make sure that the following parts are in good order.

* Battery
* Ignition system
* Engine oil and coolant levels
* Fuses
* ECM harness connector
* Vacuum hoses
* Air intake system
* (Oil filler cap, oil level gauge, etc.)
* Fuel pressure
* Engine compression
* EGR valve operation (If so equipped)
* Throttle valve
* Evaporative emission system

2) On air conditioner equipped models, checks should be carried out while the air conditioner is OFF.
3) On automatic transmission equipped models, when checking idle rpm, ignition timing and mixture ratio,
checks should be carried out while shift lever is in “N” position.
4) When measuring “CO” percentage, insert probe more than 40 cm (15.7 in) into tail pipe.
5) Turn off headlamps, heater blower, rear defogger.
6) Keep front wheels pointed straight ahead.
7) Make the check after the cooling fan has stopped.

INSPECTION PROCEDURE

1 INSPECTION START
1. Visually check the following:
I Air cleaner clogging
I Hoses and ducts for leaks
I EGR valve operation (If so equipped)
I Electrical connectors
I Gasket
I Throttle valve and throttle position sensor operation
2. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
Ensure engine stays below 1,000 rpm.
3. Open engine hood and run engine at about 2,000 rpm for about 2 minutes under no-load.
4. Perform diagnostic test mode II (Self-diagnostic results).
OK or NG
OK ' GO TO 2.
NG ' 1. Repair or replace components as necessary.
2. GO TO 2.

2 CHECK IGNITION TIMING
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Turn off engine and disconnect throttle position sensor harness connector.
4. Start and rev engine (2,000 - 3,000 rpm) two or three times under no-load, then run at idle speed.
5. Check ignition timing with a timing light.
15°±2° BTDC (in “P” or “N” position)
OK or NG
OK ' GO TO 4.
NG ' GO TO 3.

3 ADJUST IGNITION TIMING
1. Adjust ignition timing by turning distributor after loosening securing bolts.
2. Turn off engine and connect throttle position sensor harness connector to throttle position sensor.
' GO TO 2.


4 CHECK BASE IDLE SPEED
1. Check idle speed.
700±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 6.
NG ' GO TO 5.

5 ADJUST BASE IDLE SPEED
1. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run engine at idle speed.
2. Adjust idle speed by turning idle speed adjusting screw.
700±50 rpm (in “P” or “N” position)
' GO TO 6.

6 CHECK TARGET IDLE SPEED
1. Turn off engine and connect throttle position sensor harness connector.
2. Start and rev engine (2,000 to 3,000 rpm) 2 or 3 times under no-load then run at idle speed.
3. Check idle speed.
750±50 rpm (in “P” or “N” position)
OK or NG
OK ' GO TO 9.
NG ' GO TO 7.

7 DETECT MALFUNCTIONING PART
Check the following.
1. Check IACV-AAC valve and replace if necessary.
2. Check IACV-AAC valve harness and repair if necessary.
3. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 9.

9 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Run engine at about 2,000 rpm for about 2 minutes under no-load.
2. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
3. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 12.
NG (MIL does not blink.) ' GO TO 17.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.


10 CHECK FRONT HEATED OXYGEN SENSOR LH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Left bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' GO TO 13.
NG ' GO TO 11.

11 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit.
Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.


13 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
2. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG (MIL does not blink.) ' GO TO 16.
NG (MIL blinks less than 5 times.)
' 1. Replace front heated oxygen sensor RH.
2. GO TO 14.


14 CHECK FRONT HEATED OXYGEN SENSOR RH SIGNAL
1. Warm engine to normal operating temperature.
2. Run engine at approx. 2000 rpm for approx. 2 minutes under no-load.
3. Set “Right bank front heated oxygen sensor monitor” in the Diagnostic Test Mode II.
4. Make sure that MIL goes on more than 5 times during 10 seconds at 2,000 rpm.
OK or NG
OK ' INSPECTION END
NG ' GO TO 15.

15 DETECT MALFUNCTIONING PART
Check the following.
1. Check fuel pressure regulator.
2. Check mass air flow sensor and its circuit.
3. Check injector and its circuit. Clean or replace if necessary.
4. Check engine coolant temperature sensor and its circuit.
5. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.
16 CHECK FRONT HEATED OXYGEN SENSOR RH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor RH harness connector.
4. Check harness continuity between ECM terminal 50 and front heated oxygen sensor RH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

17 CHECK FRONT HEATED OXYGEN SENSOR LH HARNESS
1. Turn off engine and disconnect battery ground cable.
2. Disconnect ECM harness connector.
3. Disconnect front heated oxygen sensor LH harness connector.
4. Check harness continuity between ECM terminal 51 and front heated oxygen sensor LH harness connector.
Continuity should exist.
OK or NG
OK ' 1. Connect ECM harness connector.
2. GO TO 18.
NG ' 1. Repair or replace harness.
2. GO TO 9.

18 PREPARATION FOR “CO” % CHECK
1. Disconnect engine coolant temperature sensor harness connector.
2. Connect a resistor (4.4 kW) between terminals of engine coolant temperature sensor harness connector.
' GO TO 19.

19 CHECK “CO” %
1. Start engine and warm it up until engine coolant temperature indicator points to the middle of gauge.
2. Rev engine (2,000 to 3,000 rpm) two or three times under no-load, then run engine at idle speed.
3. Check “CO” %.
Idle CO: 1.5 - 9%
After checking CO%,
a. Disconnect the resistor from terminals of engine coolant temperature sensor.
b. Connect engine coolant temperature sensor harness connector to engine coolant temperature sensor.
OK or NG
OK ' 1. Replace front heated oxygen sensor LH.
2. GO TO 10.
NG ' GO TO 20.

20 DETECT MALFUNCTIONING PART
Check the following.
1. Connect front heated oxygen sensor harness connectors to front heated oxygen sensors.
2. Check fuel pressure regulator.
3. Check mass air flow sensor and its circuit.
4. Check injector and its circuit.
Clean or replace if necessary.
5. Check engine coolant temperature sensor and its circuit.
6. Check ECM function by substituting another known good ECM.
(ECM may be the cause of a problem, but this is rarely the case.)
' GO TO 2.

Aug 17, 2008 | 2000 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...