Question about Cars & Trucks

Open Question

LG5801XSW3 will not start

When I push the "push to start" button, my Whirlpool model LG5801XSW3 will not start. Thermal fuse checks good so as the push to start push switch.

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
fletcherj316
  • 30 Answers

SOURCE: 2003 lincoln towncar cartier decklid wont open with remote or door button and door button clicks when pushed

Has the rod become disconnected form the lock our the solinord so it can't open check this .

Posted on Jan 25, 2015

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electric window problems


Start small. Check the fuses. If all good, push your window button. If you don't hear anything, it's either a bad switch, window motor, broken wire, or loose connection. If you hear the window motor while pushing button, yet the window won't go up or down, then it either came off track or the window motor gears stripped out

Aug 29, 2016 | 1999 Honda HR-V

1 Answer

Wont start


Check dryer Terminal block prongs both outside prongs should give combined 220, and 110 each if u check 1 outside & 1 center (ground) prong. Also check house electrical outlet for full voltage.

CHECK THERMAL SHUT OFF THERMOSTAT USUALLY LOCATED ON THE BLOWER. for OHMS or resistance with a meter. Should show a closed circuit. Ohms WHEN THIS FUSE BLOWS IT WILL SHUT DOWN EVERYTHING.

NEXT Test the PUSH start switch with meter for OHMS. Should show OHMS when pushed in or on start, and no ohms or infinity when in off position.

If you hear a humming/clicking sound from motor area you more than likely have a bad motor.
Try this test out to see if u have weak windings or relay/capacitor on motor.
Open the dryer door and turn by hand the drum while machine is on ON position. And you or someone else presses the door engagement switch in. If it starts up then u have bad windings

Another thing to check is the belt safety switch. With a multi meter.
Especially if u just replaced the belt. The belt safety switch is attached to the Tensioner and motor. IT LOOKS LIKE A DOOR SWITCH SOMEWHAT a little black pc of plastic with 2 prongs going into it. Sits at bottom of motor. Under the Tensioner. Attach meter clips to the 2 prongs on switch, Then when the little white push button is pressed in it should show continuity and none when released.

Lastly check ut push start button for continuity with a meter when pushed in the on position, it may have gone bad.

Apr 13, 2015 | Cars & Trucks

1 Answer

Can I install a push button start on my 94 c1500 suburban?


Sure can. cut the yellow wire off the ignition switch under the dash. Run a fused wire (40 Amp is good) from the battery to the push button. Put the yellow wire to the push button. Beware though, you are bypassing the neutral safety switch. It will crank anytime you push the button.

Dec 19, 2014 | Cars & Trucks

1 Answer

1993nissanpickup d21try startin but just click new battery


check your ignition switch solinoid, it could be shot or check your starter relays and fuses, check the theft prevention switch just under the ignition cylinder. there are multiple things that could be causing this problem, but if your like me, you can just bypass all the starting relays for the starter and run a switch inside the cab to push that runs directly from the battery to the starter, and install a push-start button on the dash. let me know if this has helped you any, good luck.

Razer Neil

Jul 11, 2014 | 1993 Nissan Pickup

1 Answer

All fuses and relays are good. It jest cranks over but wont start. However it will start with starting fluid but quits when I quit spraying it.


Hello, Check under the dash, behind the passengers kickpanel for a switch. Sometimes the switch will have an access hole in the panel. It is a safety switch called an Inertia sensor. There is a push button on it. You just press the button and hold it down and it should connect the fuelpump.

This switch is suppose to trip on impact. But sometimes loading a truck or closing a door will trip it.

Feb 14, 2011 | 2002 Ford E350

2 Answers

When I turn the key to the start position, the starter does not engage


first check the battery make sure its fully charged then check fuses and relays then check startor motor and if it is not any of these it could be the igntion switch good luck

Dec 10, 2010 | 2004 Chevrolet Cavalier

1 Answer

Do not here washer pump kick in when pushing the button


First check your fuses. If they are good then check voltage with a digital or analog meter. At pump motor while the button is being pressed. If power is present suspect faulty pump motor. If no power is present and fuse is good check for shorts or broken/burnt wires in between. Check the switch also, the switch can be looped or jumper wired.

Jun 23, 2010 | 2006 Chrysler Town & Country

1 Answer

Cant push the button to put in gear


CHECK MAKE SURE BATTERY FULLY CHARGED IT HAS TO BE 12.5 VOLTS BEFORE THE BRAKE TRANSMISSION SHIFT INTERLOCK SOLENOID WORKS.IF BATTERY POWER GOOD CHECK BRAKE LIGHTS TO SEE IF BRAKE LIGHTS SWITCH IS WORKING.IF NO CHECK FUSE.IF FUSE GOOD BRAKE LIGHT SWITCH IS FAULTY. IT CONTROL THE BRAKE TRANSMISSION SHIFT SOLENOID ALSO THE NEUTRAL SAFETY SWITCH.IF FUSE AND BRAKE LIGHT SWITCH IS GOOD.YOUR PROBLEM COULD BE A FAULTY NEUTRAL SAFETY SWITCH OR BRAKE TRANSMISSION SHIFT SOLENOID FAULTY.

May 05, 2010 | 2001 Chevrolet Cavalier

1 Answer

Pushed button...no light & no 4wd


Check the fuse to the 4x4, if the fuse is good then check the 4x4 electric motor actuator on the transfer case. You should hear it work from 2wd, 4hi to 4low and back to 2wd with the push of the switch. if you don't hear it working then check the wire harness at the actuator motor, look for any damages like corrosion or cracked wire connector clips. If the 4x4 actuator is working on the transfer case, then the front hub 4x4 actuator may have gone bad and that's located on the front differential. It's common for the clip there to corrode and break and is an easy fix with a new collar pin, at worst it's the diaphragm on the vacuum actuator that is located under the battery tray. There is a vacuum switch on the top of the transfer case, driver side but when that fails, your front hub stay's locked in the on position. Good luck and keep me posted and hope it's a simple fuse that has gone bad. You can pick up all these parts at Auto Zone or Parts Source and they will have the step by step instructions for you to get the job done with common tools.

Dec 30, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...