Question about Land Rover Discovery

Open Question

Discovery 2 tdi windscreen wipers dont work

Widscreen wipers dont work

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: Windscreen Washer

If it is the same as some other Chevrolets they have 2 pumps attached to the side of the washer bottle. 1 for rear and 1 for front windscreen

Posted on Jul 31, 2008

Ad
lastech
  • 408 Answers

SOURCE: wipers not working in the 1 2 3 position merc c220 2006

hello,seem your combination switch have problem,remove your under dash,maybe poor connection on wiring or your combi. switch defective,ty

Posted on Apr 16, 2009

TDISLine
  • 1874 Answers

SOURCE: Windscreen wipers not working. Is this the motor

I had this problem two years ago on my Audi A4. First you must diagnose this problem. In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works. Heed of the windscreen !!! Refit in reverse order. Please Rate my Response! Thanks!

Posted on Sep 29, 2009

babaphat
  • 24 Answers

SOURCE: windscreen wiper on Mercedes C200 not working

you should check the connection to the main board and the connections to the motor for the wipers. these sometimes become gunked up, so when you pull them apart to check them clean them with sand paper or something that can scrub them like a green scratch pad

Posted on Dec 24, 2009

  • 149 Answers

SOURCE: On a land rover discovery, windscreen wiper motor,

Ok, here are the wiring colors and functions/destinations. C0030 is the motor connector for the front windscreen.
C0030-1 - Black, runs to a Earth
C0030-2 - White/Green - Fed from the front wiper relay, via the IDM
C0030-3 - Blue/Green - Flick Wipe/Fast Wipe
C0030-4 - Green/SlateGrey - Power from Aux Relay
C0030-5 - Red/Green - Looks to be a speed control connection.

It's hard to tell to be honest, you'd really need to sit down with RAVE and the electrical circuit diagram and the operation description to make head or tail of it.

Posted on Feb 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2002 ford focus windscreen wipers at the front dont reset properly. Any ideas?


It is likely the wiper motor is defective due to a failed park circuit switch inside the wiper motor drive.

Jun 22, 2016 | Ford Cars & Trucks

1 Answer

My windscreen wiper where frozen with the switch on, they are not working . will it have blown a fuse discovery 300tdi


When you say with the switch on, do you mean they were frozen when wipers were moving?
if you turned then on when frozen they would take a large curent from bttery which most likely would cause a fuse to blow.

Dec 17, 2013 | Cars & Trucks

1 Answer

How do I replace the windscreen wiper motor on an audi a4 2.5 tdi


How to change a wiper motor & repair wiper mechanism on 2004 Audi A4 2.5 TDI

First time you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows:

1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!!
2. Disassemble the plastic covers from the bottom of the windscreen.
3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables.
4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi.
5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters.
6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation!
7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Mar 30, 2011 | 2004 Audi A4

1 Answer

Wiper Blades not working properly


First you must diagnose why windscreen wipers going slow and/or stopping.
In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works.
Heed of the windscreen !!!
Refit all in reverse order.

Please rate my response. Thanks!

May 25, 2010 | 2004 Audi A4

1 Answer

Audi avant estate 1.9 tdi 1996 windscreen wiper control, only fast setting working


First you must diagnose this problem. In order to find out the cause of wipers stopping you can try follows: 1. Carefully extract the wiper arms from their axles (two pieces). In some cases you need to use an extracting tool. Heed of the windscreen !!! 2. Disassemble the plastic covers from the bottom of the windscreen. 3. With the bonnet up you can start the engine, (transmission in "N" or "P" position and parking brake on). Now you must switch on the control lever of the wipers, and go to the engine compartment. If the wiper motor runs let the wiper motor running for a few minutes and switch off. Go to the step 4. If the wiper motor do not runs you must check first the electrical feeding of the motor. It is necessary to unscrew three bolts of the mechanism and disconnect the electrical coupling (difficult assurance). If the electrical feeding is OK you must replace the motor - steps 5, 6, 7. If not you must check electrical connections, the control switch of wipers and electric cables. 4. Now you must check the two bearings of wiper mechanism with your hand. In the most cases the left bearing is out of order (is very hot). This is the most encounter fault of the wipers running at Audi. 5. For have enough space to manipulation the wiper motor together with their mechanism you must extract the plastic cover of the engine computer box, and extract also the box screws. Then you can move slowly the engine computer box, just for a few milimeters. 6. You must disconnect the electrical coupling of the motor (difficult assurance), unscrew three bolts of the mechanism and extract together with the motor. You must move them slowly between windscreen and engine computer box until the wiper motor go out together with the mechanism. This is the most difficult operation! 7. Now you can repair the bearings, replace entire wiper mechanism or replace the wiper motor. It is not very simply, but it works. Heed of the windscreen !!! Refit in reverse order. Please Rate my Response! Thanks!

Sep 24, 2009 | 2004 Audi A4

1 Answer

On a land rover discovery, windscreen wiper motor, there are 5 coloured wires. Can you tell me what each one does, ie. green -- earth brown -- constant + red -- fast blue -- slow black -- intermitant...


Ok, here are the wiring colors and functions/destinations. C0030 is the motor connector for the front windscreen.
C0030-1 - Black, runs to a Earth
C0030-2 - White/Green - Fed from the front wiper relay, via the IDM
C0030-3 - Blue/Green - Flick Wipe/Fast Wipe
C0030-4 - Green/SlateGrey - Power from Aux Relay
C0030-5 - Red/Green - Looks to be a speed control connection.

It's hard to tell to be honest, you'd really need to sit down with RAVE and the electrical circuit diagram and the operation description to make head or tail of it.

Sep 01, 2009 | 1999 Land Rover Discovery

1 Answer

Replacing Windscreen For BMW 325I


i hate it when that happens
i have save a lot of money this year
my mate got my car tinted and something else done to it which he wont tell me
and i have not had one chip
Evan had rocks spread at the car by a road train and bot one chip or crack
the best window for your car is a safety glass or triple glazed glass
these age so strong it is not funny
dont know with resestance but my car has done 270kph and no trouble
as i said matt wont tell me what he did to them he works at a window company
hope this helps
ricko

Dec 29, 2008 | 2003 BMW 325

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...