Question about 1992 Mercury Cougar

1 Answer

I have no turn signals only hazards where is flasher located

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 35 Answers

Underneth your driverside dash. Its a small black relay. You can go to Autozone and they should be able to show you where and how to replace it

Posted on Jan 26, 2009

6 Suggested Answers

  • 20 Answers

SOURCE: location of flasher for turn signal

  1. Access the COMBINATION Turn Signal and Hazard INDICATOR FLASHER on the Left-Hand (drivers) side of the instrument panel in the fuse junction panel.
  1. Remove turn signal flasher/hazard indicator flasher by pulling indicator flasher straight out.
  1. To install, align the terminals of the flasher and press into place.
How about a picture--

388df46.gif

Posted on Nov 23, 2008

  • 1 Answer

SOURCE: 1994 devilles flasher location

Turn signal flasher module is behind dash left of steering column near chime module. I have a 94 Seville and I had that same problem you need a Turn Signal Flasher Moduel, I forgot the proper term for it but I had to get mine replaced too. When I hit the signals to turn the side light would come on but the signal light wouldn't. Its a little box you get from Cadillac it only cost like $20 - $25 and you get it installed and trust. It'll work again. I just got mine done this week and my car now has turn signals again.

Posted on Dec 15, 2008

  • 840 Answers

SOURCE: Location of Turn signal flasher for 95 Nissan 4wd 4cyl MT

the flasher is under the dash its about 1-2 inches round and about an 1 inch thick Please rate my response thank you very much

Posted on Jan 28, 2009

chuck943
  • 783 Answers

SOURCE: 1999 ford expedition turn signals not working

It is behind center of instrument cluster just above the accel pedal in the blower/flasher relay block,it is actually a relay on this vehicle.

Posted on Feb 28, 2009

  • 272 Answers

SOURCE: 1997 sonoma turn signal flasher

The flashers are located behind the instrument panel trim, roughly between the base of the steering wheel and the ashtray, just to the left of the car lighter. To access the flashers, you need to at least loosen the lower instrument panel trim. Just under the steering column there are two screws with star heads. One to the left of the column and one to the right. You need to remove both of these screws. You will need to remove your ashtray. On the upper left corner of the hole left by removing the ashtray is a 9/32 hex head screw. You need to remove it. Once these three screws are removed you should be able to pull down on this portion of trim under your instrument cluster. When you do this it may cause trim around your instrument cluster to loosen that you can just pop back into place with your hand. You won't need to pull down to far on this trim piece as there are still some screws holding the bottom. You should be able to pull it down far enough to see the flasher units behind and just to the left of the cigarette lighter. There are two flasher units and I found that the one on the right is for the turn signals.On the left the other is for the hazard flashers. It may be a hand scraping experience to replace the flasher but it beats paying someone to do it for you. They are easy to recognize because the are silver and round metallic plug ins. The flasher unit on the left is for the emergency flashers and the one on the right is for turn signals. You can place the emergency flasher unit into the slot the turn signal unit belongs until you get a replacement. These flasher units are pretty cheap.

Posted on Jun 02, 2009

  • 1 Answer

SOURCE: turn signals hazards flasher don't work jeep

I NEED TO LOCATE THE SWITCH WHERE IS IT ?
MY INDICATORS NOR HAZARD LIGHTS ARE WORKING I DONT KNOW WHAT IS WRONG WITH IT CHANGED BULBS BUT NOTHIGN THEY ALL WENT OUT AT THE SAME TIME
SO THERE MUST BE A RELAY SWITCH SOMEWHER BUT DONT KNOW WHERE ?
THANKS FOR HELPING

Posted on Apr 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1985 LeSabre flashers work turn signals don't need location of turn signal switch or are they one of the same


You mean turn signal flasher? No, the hazard flasher and turn flasher on older cars were separate. Often, the hazard flasher was right of the steering column (under the dash), and the turn flasher was left of the column. Look for two similar canisters. Turn the hazard lights on and locate the hazard flasher by feel or hearing. The turn flasher will be the other one. They both may be retained by metal clips.

Sep 16, 2015 | Cars & Trucks

1 Answer

Location of signal flasher module in 2004 blazer


Hazard and Turn Signal Flasher Replacement
Open the glove box to expose the glove box retaining tab (1). Lift the retaining tab and allow the glove box to hang freely.
Using a suitable flat-bladed tool, release the plastic retainer that retains the hazard/ turn signal flasher (1) to the C203 body harness connector (2) . Remove the hazard/ turn signal flasher (1).

Jun 12, 2015 | 2004 Chevrolet Blazer

1 Answer

Can not locate turn signal flasher unit. located hazard flasher but turn signal flasher is not on the same block even though the block is labeled for the turn signal flasher.


usually the one flasher serves both turn signal & hazard flasher, if either one isn't working you may have other problems.....hope this helps.....cheers.

Jun 27, 2011 | 1989 Plymouth Acclaim

1 Answer

No turn signals or hazards???


Check the FLASHER unit; the turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Hazard flasher -->> The Flasher is located: Front seating area, passenger side, under dash, below glove compartment, mounted in fuse panel

Turn signal -->> The Flasher is located: Front seating area, driver side, under dash, mounted on passenger side of steering column

Good luck (remember comment and rated this).

Apr 23, 2010 | 1995 Chevrolet Monte Carlo

1 Answer

Where is the turn signal flasher on a 1994


There are 2 flasher relays. One for the turn signals and one for the hazard lights. Turn Signal Flasher is located on the driver's side, under dash, mounted on upper passenger side of steering column support. Hazard Flasher is located same place only it is mounted on the driver's side of the steering column.

Apr 23, 2010 | Pontiac Firebird Cars & Trucks

2 Answers

Where is the turn signal\hazard flasher located?


it's in the auxiliary relay box behind the glove box.

13350 is base part number on flasher

Feb 03, 2010 | 2003 Ford F250 Super Duty Crew Cab

3 Answers

Where does the flasher go on a 98 chevy malibu


Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.
  1. Remove the bezel from the ignition switch.
7f58edd.gif
Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.

9f5c3cc.gif
To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .

bd28884.gif
. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.

daa6205.gif
Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.

c506713.gif
. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

Dec 01, 2009 | 1998 Chevrolet Malibu

1 Answer

Haz flashers wont work but blinkers do


There are 2 seperate flashers 1 for turn signals and 1 for hazard.The hazard flasher is located in the convenance center the turn flasher in the fuse box. Also seperate fuse's for each. One battery circuit for hazard Ignition for turn signals.Check fuse for hazard,if good try swapping in the turn signal flasher and see if hazards work.They use the same flasher unit.

Aug 20, 2009 | 1993 GMC Safari

4 Answers

Flasher location


I believe the hazard/flasher relay is located under/left of the dash . I think if you remove the under panel under the steering column it should be attached to the BCM bracket under the dash on the left side.

Remove the left instrument panel (IP) insulator.
Remove the steering column filler panel.
Slide the hazard and turn signal flasher to the right, releasing the tabs from the Body Control Module (BCM) bracket.
Disconnect the electrical connector from the hazard and turn signal flasher.

Hope this helps.....

Apr 29, 2009 | 2003 Pontiac Grand Prix

2 Answers

Location of flasher for turn signal


  1. Access the COMBINATION Turn Signal and Hazard INDICATOR FLASHER on the Left-Hand (drivers) side of the instrument panel in the fuse junction panel.
  1. Remove turn signal flasher/hazard indicator flasher by pulling indicator flasher straight out.
  1. To install, align the terminals of the flasher and press into place.
How about a picture--

388df46.gif

Oct 03, 2008 | 1996 Ford Thunderbird LX

Not finding what you are looking for?
1992 Mercury Cougar Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...