Question about Cars & Trucks

1 Answer

Where is the fuel pump power relay - Cars & Trucks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 183 Answers

Somewhere on a boat ?china las Vegas who knows the point is its very hard to answer a question with out proper information like make and model year of car/truck/boat/plane/golf cart i think you get the idea

Posted on Jan 20, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

keemo68
  • 1263 Answers

SOURCE: Fuel Pressure

did you reset full cutoff switch? this will be located in the rear of the vehicle in the wheel well behind the fabric. in some cases they are located underneath the drivers seat.

Posted on Aug 29, 2008

  • 979 Answers

SOURCE: 1996 CADILLAC DEVILLE, NO POWER TO FUEL PUMP

Check for a burned fusible link under the hood. If you have power at the fuel pump relay, you could have a bad ignition switch or bad oil pressure switch...accordianman

Posted on Dec 15, 2008

  • 29 Answers

SOURCE: fuel pump relay

Located under the steering wheel. The fuse should be #28 and the relay will have 167 or 409 on it. Here is a link to a wire diagram for the TT
http://mk1tt.montebellopark.com/pdf/2002MYStdEquipWiring.pdf

Posted on Feb 06, 2009

lsteward68
  • 331 Answers

SOURCE: i can get power th the fuel pump when i run a hard wire from the battery to the relay but when i put the relay back in no power to the fuel pump

I have a question. Turn the ignition on you should hear the pump for about 3 seconds. then it should stop. this is normal operation. then when a signal is sent to the ignition that you are going to crank it then it switches on. I can see how this can seem like the pump is not working but after you crank it you should be able to hear the pump for about 1-1.5 seconds after the crank then it will stop. The pump will not turn on until it is told to do so by the computer.

Posted on May 25, 2009

localwonder
  • 6784 Answers

SOURCE: no power at fuel pump chev.S-10 looking for fuel pump relay and fuse

The fuel pump relay is located Under hood, driver side, upper firewall, mounted in relay block.

The fuse is located under the instrument panel to the left of the steering column. The fuse block should be visible from underneath the steering column, near the pedal bracket. If the panel is not visible, check for a removable compartment door or trim panel which may be used on later models to hide the block.



Posted on Jun 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the fuel pump relay don't click when i turn the key to run? and why there is no power at the fuel pump relay?


the operation of most fuel pumps is controlled by the fuel pressure regulator
when the fuel pump gets to set pressure , the pump is switched of by the ECM at the relay level
maybe nothing wrong with your system just the system working as designed
if you have pressure in the fuel manifold when you turn the ignition on then the pump will not run but will if there is a fuel leak somewhere and the pressure drops off

Oct 25, 2016 | Cars & Trucks

1 Answer

05 Chevy cobalt have no power to fuse block for fuel pump


You have no voltage at 15 amp fuel pump fuse in the under hood fuse/relay center ? There is a fuel pump relay also in same under hood fuse box. The fuel pump fuse gets power from the fuel pump relay. The ( PCM ) engine computer controls that relay, gives power or ground electronically to turn the relay on giving power to the fuel pump through the fuel pump fuse. You could have a bad relay or an anti-theft system problem . What engine does you vehicle have 2.0 L or 2.2 L the 2.0 L engine gets power differently to fuel pump .

Dec 28, 2014 | 2005 Chevrolet Cobalt

2 Answers

2000 durango check fuel pump asd,fuel pump relay,fuel pump fuse all ok, still no power


Sounds like a ground problem to me. Current won't flow without a ground.

Sep 05, 2014 | 2000 Dodge Durango

1 Answer

No fuel pressure in efi system


Either the fuel pump is not working, or the filter is totally blocked.
The fuel pump circuit needs checked to see if it's a wiring problem or a failed fuel pump. There will be (probably) a fuel pump fuse in your fuse block, and a fuel pump relay under the hood.
If you check the fuel pump wire for power at the gas tank connector while the engine is cranking over, and there is power there, and the ground for the pump is good, then the pump is not working and will have to be replaced. If you do not have power when cranking, the wiring at the fuel pump relay will have to be checked. Simple relay- has a power feed for the pump at one relay terminal (it is hot at all times), and a fuel pump wire to pump on another terminal (the power out for relay). When relay coil side is energized from a signal from computer, the relay contacts close and power is sent to the pump. The other relay terminal is a ground for the coil side of relay. Pull the relay out and you will see the diagram etched on it. If there is a fifth terminal, that could be a pump prime terminal, or a way to keep the pump running when engine is running through the oil pressure switch. But when cranking the engine, the computer will signal the relay to send power to the pump.

Dec 31, 2013 | Cars & Trucks

1 Answer

I have a 1996 mustang v6 no power to fuel pump. Bought used fuel pump relay still have np power. Safty switch is good. Unpluged fuel turned switch on and i have constant power of 9.52 volts plug in pump...


9.5 volts sounds like the power coming from the gas gauge.
I am showing a relay module with the fuel pump and pcm relays built in along with two other relays. The fuel pump relay should not be accessable. In most cases the pump relay gets power from a 20amp fuse and the computer grounds the relay when needed. Power goes from the pump relay to the inertia switch then to the pump. So the inertia switch should be hot when the pump relay is activated.

Jun 12, 2013 | Cars & Trucks

1 Answer

Car will turn over but won't start. Through the


No noise from fuel pump when you turn over the car .First thing get voltage at fuel pump relay checked, is there 12 volt to the relay.If no, then problem is again the relay.--------- To reconfirm the problem, try other test, that is remove the relay and by pass the relay terminals with a jumper wire .Then with 12 volt external battery give power to fuel pump connector and see, if the fuel pump starts, then its clear that fuel pump relay is faulty.----------- Also other problem can be fuel pump inertia switch.If the inertia switch is faulty then also fuel pump will not start.-------- The fuel pump relay on a 1995 Ford Explorer is in the power distribution
box, in the engine compartment, driver's side near the firewall.----------
The fuel pump inertia switch is in the right front passenger area
it is below the dash but above the carpet in the right hand corner.--------
Its a push button type inertia switch.
--------
Fuel Pump Activation
When ignition switch is turned to START position, PCM operates fuel pump relay to provide fuel for starting engine. PCM senses engine speed and shuts off fuel pump by opening ground circuit to fuel pump relay when engine stops or engine speed drops to less than 120 RPM. When ignition switch is in ON position, EEC power relay is energized (contacts closed). Power is provided to fuel pump relay and timer in PCM. Fuel pump receives power through fuel pump relay contacts.
Inertia Fuel Shutoff (IFS) Switch
All models use an electrical interrupt switch in fuel system. During a collision or vehicle rollover, electrical contacts within inertia switch open, shutting off fuel supply to electric fuel pump. Fuel supply is interrupted even when engine is running.
A reset button is located on switch assembly. If electrical circuit trips, vehicle will not restart until switch is reset. Fuel system should be inspected before resetting switch.
IFS switch is located under instrument panel, near right side of transmission hump.
----------- If the fuel pump relay, the inertia switch and fuel pump all checked ok, and fuel pump is working with direct 12 volt source to fuel pump.Then problem relates to computer.The computer (power control module, PCM) is faulty and has to be replaced.--------- This will help.Thanks.Helpmech.

Jul 17, 2011 | 1995 Ford Explorer

2 Answers

I have a 98 jimmy.4dr, 4wd..problem --no power to fuel pump....if you stand on drivers side looking at fuse panel (the top right pin of the relay has power, but thats the only one...if i jump power to the...


Fuel Pump Electrical Circuit
OPERATION
When the key is turned ON with out the engine running, the control module turns a fuel pump relay ON for two seconds. This builds up fuel pressure quickly. If the engine is not started within two seconds, the control module shuts the fuel pump OFF and waits until the engine starts. As soon as the engine is cranked, the control module turns the relay ON and runs the fuel pump.
When the engine is cranking or running, the control module receives the Crankshaft Position (CKP) sensor reference pulses which in turn energize the fuel injectors. As a back-up system to the fuel pump relay, the fuel pump can also be turned ON by a fuel pump oil pressure switch. When the
engine reaches about 28 kPa (4 psi), and the fuel pump relay does not complete the circuit, the fuel pump oil pressure switch will close to complete the circuit to run the fuel pump.

An inoperative fuel pump relay can result in long cranking times, particularly if the engine is cold. The fuel pump oil pressure switch will turn ON the fuel pump as soon as oil pressure reaches about 28 kPa (4 psi).



You can test to see if the relay it's self is bad by swapping it temporarily with another relay. If your truck has AC then that one should be compatible. Just compare the two to see if they're the same and if so, try using the AC's relay.

Apr 05, 2011 | GMC Jimmy Cars & Trucks

1 Answer

1997 Ford F150 Electric Fuel Pump will npt pump


Did you check the fuel inertia switch in the passenger side kick panel ?

The fuel pump is powered :
the fuse to the fuel pump relay.
The fuel pump relay to the fuel inertia switch
The fuel inertia switch to the fuel pump itself.

At the fuel inertia switch in the kick panel, power from the relay is the Dark Green w/ Yellow stripe wire and the pink w/ black stripe wire is the power. from the fuel inertia switch to the fuel pump.

If you jumper the fuel pump relay, you should hear it run. If not pull the fuel pump relay, and check the pins in the relay socket, pin 30 should be the power from the fuse.

50b0c31.jpg

If you have power at pin #30, jumper the relay socket as shown with the red line above, and check the dark green w/ yellow stripe wire at the fuel inertia switch for power.
Press the button on the top of the fuel inertia switch, and check for power leaving the fuel inertia switch on the pink w/ black stripe wire.

This is tests good, check for power at the fuel pump, same pink w/ black stripe wire.
Fuel inertia switch info is in the owners manual, If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

Jan 03, 2010 | 1997 Ford F150 Regular Cab

6 Answers

No power to fuel pump


when u checked this u do realize the fuel pump only has 12 volts for 1 second then the computer turns it off unless the engine is started? let me know.

Dec 03, 2009 | 1997 Dodge Ram 1500 Club Cab

3 Answers

No power to fuel pump


Hi..my name is Keith..and the 2 things that i know of...that will not let power go to the fuel pump is 1..the fuel pump relay being bad..or 2..that something has tripped the Inertia Switch...and it needs resetting..i hope this will help

Jun 30, 2009 | 1994 Ford Ranger Supercab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...