Question about 2000 Ford Focus

1 Answer

What torque for rear wheel bearing Ford Focus 2000

Changed wheel cylinder and shoes on rear of Ford Focus 2000 Td di estate (Ghia) 1800 cc. Need to know torque setting for rear wheel bearings.

Posted by on

  • 5 more comments 
  • Anonymous Mar 17, 2014

    rear bearing torque

  • Anonymous Mar 21, 2014

    back wheel bearing nut what dose it torque at

  • Anonymous Mar 22, 2014

    tranny sliping on accelerate no its not rear wheel diffy

  • Anonymous Mar 27, 2014

    torque setting

  • Anonymous Mar 28, 2014

    need to set torque on cylinder head

  • Anonymous Mar 31, 2014

    torque specification for whell bearing hub

  • Anonymous Mar 31, 2014

    torque

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

Can only find out that the hub needs to be tightened to
235 nm Dunno if this helps

Posted on Jan 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

1 Answer

How do you release the rear brakr shoes to remove the drum and bearings?


Remove or disconnect the following:
  • Rear wheel
  • Wheel speed sensor, if equipped
  • Brake drum, bearing and spindle assembly
  • Brake shoe hold-down springs and pins
  • Brake shoe assembly from the wheel cylinder and anchor block
  • Parking brake cable
  • Lower return spring
  • Upper return spring
  • Primary shoe from the strut and brake shoe adjuster
  • Parking brake return spring
  • Secondary shoe from the strut support
I hope this answers your question. Best of luck!
Greg

Jun 28, 2011 | 2003 Ford Focus

1 Answer

Need to know the torque setting for the rear weel bearing on my 2001 ford focus. it takes a 30mm socket.


The torque setting 49 ft. lbs.


Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80 e0001241.jpg
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

Apr 26, 2011 | Ford Focus Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

Rear brakes 2000 ford focus zts


emergancy brake cable is froze holding the brake on

Mar 20, 2009 | 2000 Ford Focus

1 Answer

2000 Ford focus td cl estate fails to start


factory immobiliser call dealer to reset ECU

Jan 03, 2009 | 2000 Ford Focus

1 Answer

Location of diesel heater coils on a Ford Focus 1800 ghia diesel


four cylinder which means four heaters and each one is just below the injectors

Dec 06, 2008 | 2005 Ford Focus

1 Answer

Keys lock doors but will not open them


Try spraying graphite lock lube into the door lock cylinders, this usally corrects this problem.

Nov 18, 2008 | 2000 Ford Focus

Not finding what you are looking for?
2000 Ford Focus Logo

2,122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

71338 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...