Question about 1997 Toyota Camry

Open Question

1997 camry vienta 3.0 v6 3vzfe cam & timing belt position

Toyota vienta v6 3vzfe engine cam belt set up showing the correct fitment of thecam belt pulleys front and back heads and the correct a lignment of the inlet exhaust camshafts gears when in position in both cylinder heads when the timing belt is installed

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
dttech
  • 4803 Answers

SOURCE: i have installed a new

There is only 1 "set" of timing marks. If there is more than 1 then someone has modified your engine components. Here is a picture of where they should be.

dttech_46.gif

Posted on Apr 11, 2011

Ad
  • 101 Answers

SOURCE: 1993 Toyota Camry V6 Timing Settings

Get a T belt from toyota. It has 3 white lines on it and and arrow mark. 2 lines are solid and one is broken. Put the arrow facing away from the engine. The cam gears have a dot punched into them near a certain tooth. This is where the solid white lines will line up with. The crank gear will have a dot also. It will line up at 90 degrees from the top, towards the front of the car. This is where the broken line will match up with. With the belt installed with all lines on their proper dots and arrow away from the engine, you valve timming is correct.
Of course you need to remove and compress the tensioner also. I assume you know this already since you didn't ask.

Posted on Apr 16, 2009

co7196
  • 3433 Answers

SOURCE: 1998 toyota camry le 4 cylinder How do you set the

Just make sure the timing belt is on properlyy, lining up the cam and crank in proper position to each other. The engine willstart when fully assembled because the electrical has not be altered. If it has a crank position sensor , be sure to put it back on after cleaning it and the connector.

Posted on Nov 14, 2009

GeoffW1
  • 3961 Answers

SOURCE: My toyota vienta 3VZ-FE 1996 - oil leak onto exhaust

Hi,

That engine will leak oil from

- cam cover gaskets (rear one drips on the exhaust)
- camshaft end seals
- distributor shaft o-ring (appears on top of transaxle housing)
- oil filter bracket to block o-ring seal (drips on front bank exhaust)
- crankshaft nose oil seal (have done with timing belt change)
- rear main seal (expensive, leave it be)

Posted on Jan 08, 2010

Testimonial: "thanks I will try them all, the oil filter bracket first."

  • 1757 Answers

SOURCE: toyota 98 camry v6 cambelt timing marks

Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1998 Toyota Camry. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1998/make/toyota/model/camry/1998_toyota_camry_timing_belt_diagram_marks.htm

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ?


Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Feb 03, 2016 | Toyota Cars & Trucks

1 Answer

Where is the water pump on a 96 vienta?


That will be a V6. The water pump is behind the timing belt, which has to be loosened and pushed aside. You may as well replace the belt as well. See here p320

http://www.turboninjas.com/camry/eg2.pdf

This is for the 1MZ alloy engine. If you have the 3VZ iron block engine, post an email address and and I'll send you that info.

Jun 09, 2014 | 1997 Toyota Camry

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

1997 Camry Vienta 3.0 litre revs high at startup


To give you a simple answer, no. My advice is to take it to an A level technician for diagnostics. Sounds like you could have some sensors misreading.

May 30, 2010 | 1997 Toyota Camry

1 Answer

My toyota vienta 3VZ-FE 1996 - oil leak onto exhaust


Hi,

That engine will leak oil from

- cam cover gaskets (rear one drips on the exhaust)
- camshaft end seals
- distributor shaft o-ring (appears on top of transaxle housing)
- oil filter bracket to block o-ring seal (drips on front bank exhaust)
- crankshaft nose oil seal (have done with timing belt change)
- rear main seal (expensive, leave it be)

Dec 06, 2009 | 1996 Toyota Camry

1 Answer

1998 toyota camry le 4 cylinder How do you set the


Just make sure the timing belt is on properlyy, lining up the cam and crank in proper position to each other. The engine willstart when fully assembled because the electrical has not be altered. If it has a crank position sensor , be sure to put it back on after cleaning it and the connector.

Nov 14, 2009 | 1998 Toyota Camry

1 Answer

Toyota 98 camry v6 cambelt timing marks


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1998 Toyota Camry. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1998/make/toyota/model/camry/1998_toyota_camry_timing_belt_diagram_marks.htm

Aug 30, 2009 | 1998 Toyota Camry

1 Answer

I loss my remote control of my 1997 toyota vienta


You will need to have it towed to the dealer.

Jun 03, 2009 | 1997 Toyota Camry

1 Answer

Where is the timing mark on the camshaft for replacing a timing belt on a 1997 Toyota Camry 4 cylinder? I can find the hole in the sprocket but there is no mark on the bearing at the 12 o'clock or 1...


The mark on the bearing cap is actually an indentation. It is very difficult to see if the area is dirty. I usually roll the engine over till the area of the mark is between the spokes of the cam gear. Then I clean off the area and take white out and paint the mark. Then roll the engine over til the marks on the crank line up. Tehn using a mirror you should be able to see the white out through the hole in the cam gear.

Apr 15, 2009 | 1997 Toyota Camry

1 Answer

1993 Toyota Camry V6 Timing Settings


Get a T belt from toyota. It has 3 white lines on it and and arrow mark. 2 lines are solid and one is broken. Put the arrow facing away from the engine. The cam gears have a dot punched into them near a certain tooth. This is where the solid white lines will line up with. The crank gear will have a dot also. It will line up at 90 degrees from the top, towards the front of the car. This is where the broken line will match up with. With the belt installed with all lines on their proper dots and arrow away from the engine, you valve timming is correct.
Of course you need to remove and compress the tensioner also. I assume you know this already since you didn't ask.

Mar 12, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
1997 Toyota Camry Logo

Related Topics:

267 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...