Question about 2007 Volvo S40 2.4i Sedan
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The best thing is to go to your local Volvo maintenance shop or Volvo experts to find out whats the problem..usually the coomon ones I think is the programs inside its ECU unit..you try this..ask the volvo experts to reset the ECU and lets see..if problem arise then it is no doubt you might need the sensor..hope this help..
Posted on Nov 03, 2008
SOURCE: 1993 Volvo 940 error code 232
2-3-2* Fuel trim (lambda control) too lean or too rich at idle }If too rich: high fuel press., leaking injector } various driving problems Fuel trim (lambda control) too lean at idle Oxygen sensor
Posted on Jun 22, 2009
SOURCE: 2001 volvo s440 1.9t
Volvo Radiator, Thermostat and Sensors
system's temperature controls include all coolant temperature sensors,
Volvo thermostat, Volvo radiator or expansion tank cap, cooling fan(s)
and fan clutch (if equipped). These cooling system parts function
primarily independent of the engine but control the engine either
through cooling or by sending control signals to your Volvo's
The Volvo thermostat is a spring-loaded valve that opens and closes based on the temperature of the coolant flowing through it. A high temperature reading followed by a drop to normal temperature (or a continuously low temperature) is a common first sign of a sticking Volvo thermostat. However, many other conditions may cause these symptoms, so you need to know how to eliminate each possibility.
The Volvo radiator or expansion tank cap is also a spring-loaded valve reacting to system pressure. It serves to maintain proper system coolant level at predetermined pressures. It must always be replaced with an exact replacement cap with the same pressure setting. Never use other caps except for short-term emergencies!
A belt-driven fan blade for pulling air through the Volvo radiator is usually on the Volvo water pump pulley and should have a fan clutch to control it. The fan clutch allows the fan to turn with the belt at low engine speed and "free-wheel" at higher speeds. A bad fan clutch either doesn't allow the fan to spin at low speed (overheating in traffic) or doesn't allow it to free-wheel at high speed (potential overheating on highway or reduced gas mileage).
An electric fan can be either by itself (usually front-wheel drive) or auxiliary (used with a mechanical fan). Both types are controlled via a temperature sensor - in the Volvo radiator or upper Volvo radiator hose or on the Volvo thermostat or Volvo water pump housing. This sensor is usually an on/off type switch with a fixed temperature setting. (Some vehicles may have 2-3 settings for multi-speed fans.) This sensor is commonly called an "auxilliary fan switch".
Other common temperature sensors are: 1) gauge sender (variable output); 2) warning light sender (on/off type); 3) lambda and/or fuel injection sensor(s) (variable to control fuel injection settings); 4) thermo-time switch (cold start valve control). Your Volvo may have other sensors as well.
Temperature control is critical to both performance and emission control. Unfortunately, this system is the most difficult to troubleshoot without proper equipment and diagrams. It's even more difficult with computers that adjust timing, idle speed, vacuum and fuel delivery automatically to make up for potentially faulty temperature sensor signals.
Maintenance of your cooling system sensors is virtually impossible since there's nothing really to "maintain". Keeping them clean both internally (coolant replacement) and externally (engine cleaning) is the best way to ensure trouble-free driving. Checking and replacing all parts at the factory-recommended time or mileage limits helps as well
Posted on Jul 23, 2009
Replacement of the fuel pump would be the case here,unless the fuel filter needs to be changed.To find out,remove the fuel filter,and blow threw it with your mouth,kinda tast bad but it will tell you if the fuel filter is restricted.You should be able to blow threw it easy.
Posted on Oct 09, 2009
Tips for a great answer:
Jan 02, 2014 | 2007 Chevrolet Avalanche LTZ
PLEASE RATE THIS REPLY FOR ACCURACY
Mar 24, 2013 | 2004 Ford Mustang
following are the general instructions on the start of diagnosing any
electronically controlled engine or transmission problem.
The Engine and Automatic Transmission (not applicable to manual transmissions) in this vehicles drive train are fully electronically controlled by a computer called the PCM and TCM (Power Train Control Module, Transmission Control Module). When a problem like this or other drive-ability related problems occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPENDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM. Also always check fuel pressure for correct spec for your make and engine type. Also engine mechanical problems ca cause many drive-ability related problem such as rough idle and other symptoms
Oct 21, 2012 | 2009 Chevrolet Aveo 1.4
The engine and transmission in this cars drive train are fully electronically controlled by a computer called the PCM (Power Train Control Module). Whenever a problem like this occurs the computer stores a record of the problem (there are of course some exceptions to this, like the fuel pump, engine coolant temperature sensor and MAF sensor for instance) in the form of a fault code in its memory, to read these fault codes you must have the systems memory scanned with a special tool. Once the fault code(s) are read you then must perform the appropriate diagnostic testing to find and resolve the problem(s) DO NOT REPLACE ANY PARTS UNTIL A TRAINED TECHNICAIN HAS DIAGNOSED THE PROBLEM TO AVOID SPEDING YOUR HARD EARNED MONEY ON PARTS THAT MAY NOT CORRECT THE PROBLEM
Jul 19, 2012 | Cars & Trucks
Jan 27, 2011 | 2005 Volvo S40
Feb 03, 2010 | 2002 Volvo V70
Jul 23, 2009 | 1997 Dodge Intrepid
Jul 22, 2009 | 2004 Chevrolet TrailBlazer
33 people viewed this question
Usually answered in minutes!