Question about 1998 Chevrolet Blazer

1 Answer

My starter is making a grid ding nose when I try to start it what is the problem

Posted by on

  • ray f elliott Jan 21, 2013

    u may not need the shims it just depends on how the teeth hit the fly wheel it's trial and eror till u get the right one

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 66 Answers

Either your starter is bad or the teeth on your flywheel are broke off just take the starter off and u can see the teeth on the flywheel to see if there any good

Posted on Jan 20, 2013

  • Steven lay Jan 20, 2013

    I put a new flywheel in and it is still making that nose

  • Steven lay Jan 20, 2013

    And I got a new starter to I changed them both while i was under the car. And I got shims for the starter but don't know witch one to use there are three shims all deferent sizes

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced starter,battery,and altenator...still wont start,it makes a loud grinding noise


The noise u hear is the starter gri?ding against the flywheel motor most likely seized

Oct 05, 2015 | 2002 Dodge Ram Pickup 1500

2 Answers

Why wont my 99 bonneville start


Are you gettiing power to the starter when you try to start it? If not,....more than likely its a relay or wiring issue.

Sep 24, 2012 | 1999 Pontiac Bonneville

1 Answer

Makes a ding ding noise


Try spraying wd40 into the door locking mecahnism area, spray it down very well. There is a switch in there that gets dirty and sticks. It worked for me.

Jul 01, 2010 | 1997 Ford Ranger SuperCab

1 Answer

Will not turn over. good batery and bright headlights and all the electical works. place the key in ignition and it dings. when you turn over you do not hear the silinoid clicking. what do you think?


With someone holding the key to the start position try tapping the starter motor with a hammer LIGHTLY. Make sure the vehicle is in PARK!!! It sounds as tho the starter is gone.

Jun 25, 2010 | 1994 Buick Regal Gran Sport

1 Answer

Car won't start. For a while, it wouldn't start every now and then. When I insert the key and try to start it, that's it. The car makes the "ding ding" sound and the lights on the headboard and the radio...


try neutral instead of park.the safety switch could be bad.the starter relay is grounded by the pcm and the start relay can be jumped across to see if it will turn over.The relay has 4 pins,2 for the coil and 2 for the start circuit,and the pin numbers and diagram are on the relay itself. if you jump it,and the starter does not engage,you could have a bad starter.

May 18, 2010 | 2001 Buick LeSabre

1 Answer

The lights and will come on and the ding, ding from the key being in the ignition too but the car wont start dont even make a sound when i turn the key


Check for loose or corroded battery terminals. If thats OK, there may be a problem with the starter itself.

Mar 26, 2010 | 1995 Ford Taurus

1 Answer

1987 jeep yj 6 cyl manual trans. New fly wheel, clutch, presure plate, and batt. Starter is one month old on old worn flywheel with bad ring gear. Inspected starter gear before reinstalled on the new fly...


check to make sure the starter is seated correctly to the bell housing also check for a cracked! nose cone on the starter as well and make sure the front nose casting bushing isn;t worn out and make sure they sold you the correct tooth count flywheel

Jan 19, 2010 | 1987 Jeep Wrangler

1 Answer

I just replaced my starter but it makes an ugly sound. i tried shims,still makes the sound


Hello,
There are a couple things that can make starters noisy. Check the flywheel teeth for worn or damaged teeth. Next check the nose cone bushing on the starter. Alot of remanufacturing plants or Shops don't replace bushings. I have encountered this many times and it's fairly easy to do. The nose cone is the aluminum end ov the starter. you remove the solenoid and the two bolts at the back of the starter and the nose cone will come off.once it is off look at the very end of the nose cone and notice the bushing if worn will be oblong in shape. A new repair kit is less than $20.00 from auto zone and includes bushings and brushes and bendix gear.
I know cause I just used one of their kits to rebuild my starter.

Roy

Nov 16, 2009 | 1984 GMC C1500

1 Answer

Van will not start.


Sounds like it's time for a new starter. Before you go and buy a new one, check the connection to your starter for corrosion. Good luck

Apr 06, 2009 | 1992 GMC Safari

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...