Question about 1993 Mazda 626

Open Question

How to replace clutch master cylinder on a 95 mazda 626

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 166 Answers

SOURCE: mazda rx 7 rebuilt kit clutch master cylinder.

crack the bleeder nipple on the slave cyl and get some one to slowly push the pedal see if any fluid shoots out if not you may have killed the new seal in the master cyl.
it sounds like you did every thing right its just that old cylinders get were in them and if you don't hone them out and put a new sleeve in them quite often you will rip the new seal apart on the first pump of the pedal.
any way check for presser and let me no

Posted on Dec 21, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: cost to replace waterpump on mazda 626 1996

Go to (repairpal.com) and enter all your info & pick repairs for pricing in your area.

Posted on May 03, 2009

  • 1 Answer

SOURCE: 95 mazda b4000 slave cylinder bleeder valve location

the nipple sticks out side the bell housing on the left side just above your hydralic line for your clutch,auto zones web has a complete diagraham and steps for bleeding

Posted on May 09, 2009

  • 8 Answers

SOURCE: 1990 Mazda B2200 PU. Clutch sticks to the floor

I just had the same problem today it was the master cyclinder
its a common mazda problem

Posted on May 10, 2009

  • 36 Answers

SOURCE: Want to remove the ignition lock cylinder since a broken key is stuck inside.

get a phillipshead un do about 4 screws from underneath plastic cover which hides steering colume. remove cover you will see white plug on the left hand side of ignition barrel disconect.then right hand side there will be acable disconect.now get a small chissel and anti clockwise tap bolts which have no heads on them that are on top of steering colume when they are alittle bit lose use plyers its easier pull bolts out clamp will then come of and then you can pull whole ignition of. now there is 2 brass pins which hold barrel in ignition up near the key end remove and barrel will come out but it might be easier to take whole ignition to locksmith and get them to do it and get new key for around 30 bucks i did a mates about couple months ago seeya orangepeel.

Posted on May 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 98 Mazda 626 2.0l 5spd. Recently had clutch replaced, and master cylinder, but at different times, ( about 100miles apart... after clutch replcd, pedal went to floor to engage. There is no...


check the slave cylinder adjustment as normally there is no adjustment on the piston rod
There should be about 1/4 " free play between rod and throw out arm
the pivot bolt for the throw out arm should never be adjusted
what you have indicates air in the system or a faulty clutch master cylinder
you can get the clutch slipping indication if the compensating port in the master cylinder is blocked which holds the fluid in the system and keeps the clutch from fulling engaging
no resistance is air in the system and that can be from a faulty master cylinder

Apr 04, 2018 | Mazda Cars & Trucks

1 Answer

How to replace the clutch master cylinder


It says the brake and clutch master are the same one.here's a link on how to replace. SAVE 20 ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE Here are some new ones to look at. Master Cylinder Brake System at AutoZone com Best Master Cylinder Brake...

Apr 03, 2015 | 1998 Mazda 626

1 Answer

How to ajust clutch


there is no clutch adjustment. If it is slipping then the problem may be in the master cylinder compensating port and the fix is a new clutch master cylinder (cheapest fix) or bleed the system first (even cheaper fix)

Jul 15, 2014 | 1999 Mazda 626

1 Answer

2000 mazda 626 5 speed manual transmission is stuck in a gear and won't shift out


A clutch problem will not interfere with gear selection when the engine is off and the car stationary.

It does seem like you have a gearbox or gear linkage trouble.

Sep 16, 2017 | 2000 Mazda 626

3 Answers

1997 626 clutch pedal dropped to the floor. will not shift.145000mil clutch has never been replaced


u need a new clutch master cylinder an slave cylinder u have a fluid leak in the system

Jul 16, 2011 | 1996 Mazda 626

1 Answer

I'm trying to bleed out the clutch on my 1998 Mazda 626. I am having trouble locating the area I need to press to bleed it. Is there a diagram on the website or somewhere showing where this is at? I know...


The bleed nipple will be located on the slave cylinder which is mounted on the side of the transmission. If you like , you can follow the hydraulic line down from the clutch master cylinder and it will go right to it. Also, if you fill the clutch master cylinder and simply pump the clutch pedal up and down with your hand, this system will eventually self-bleed and the pedal will firm up.

May 02, 2011 | 1998 Mazda 626

1 Answer

How long to replace clutch in a 1998 mazda 626


For a 4 cylinder 2.0L engine flag time to remove and replace clutch 5.4hrs.

For a 6 cylinder 2.5L engine flag time to remove and replace clutch
6.3 hrs.

hope this was helpful for you.

Sep 09, 2010 | 1995 Mazda 626

1 Answer

Where is the clutch slave cylinder loctated?


The slave cylinder is mounted on the side of the transmission,most likely on the driver side of the vehicle,it has a line going to the master for the clutch,the master has the clutch pedal connected to it.

Aug 15, 2010 | 1992 Mazda 626

1 Answer

How do i add clutch fluid to 97 mazda 626


should be as u open the hood very larft hand side near the master cylinder will be a clear looking canister with a lid on it take it off and sdd fluid

Oct 08, 2009 | 1997 Mazda 626

1 Answer

I have a 1993 Mazda 626 LX five speed, and my clutch pedal will not go back up. I have pumped it like for 10 minutes, and I can not get into gear. Please help.


Have you checked the clutch master cylinder for fluid? First place I would look. If you don't know what it looks like, it will be next to the fire wall drivers side- looks like a brake master cylinder, but smaller. Just use plain brake fluid in it.

Sep 04, 2009 | 1993 Mazda 626

Not finding what you are looking for?
1993 Mazda 626 Logo

Related Topics:

254 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...