Question about 1998 Chevrolet S-10 Pickup

Open Question

2000 S10 CLUTCH ASSEMBLY REPAIR - 1998 Chevrolet S-10 Pickup

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 s10 with manual shift for it to start lately I have to hold clutch down and wiggle or go through the gears on the shifter ?


Hey Jason, Sounds like the clutch is about at its end.. BUT,, an adjustment might be just extend its life... BE CAREFUL.. do not abuse the transmission... it WILL cost more later... http://repair.chiltondiy.com/Pub/DIY/Product/1988-Chevrolet-S10-repair-manual-online?ca=Repair&b=3674

Jul 18, 2017 | Cars & Trucks

2 Answers

Fixed a master cylinder and slave cylinder on 2000 s10 pickup now i have no pressure on clutch what is the problem


The air needs to be bled out of system. Should have a "bleeder" on the slave cylinder resevoir. Fill 1st and open bleeder screw. Have someone push clutch pedal down and close bleeder when pedal is fully depressed. Do not pump pedal. Repeat until a steady stream of fluid is achieved. REMEMBER TO WATCH RESEVOIR LEVEL AND KEEP FULL DURING THIS PROCESS!!!! Top off when finished bleeding. This should fix your issue.

Apr 01, 2013 | Cars & Trucks

1 Answer

How do you repair broken clutch brake fluid reservior, mounting bracket that appears to be glued to the firewall from the inside? the reservior twists 90deg. and comes off and the tangs that engage the...


What you need is a clutch paddle assembly, made out of plastic, held on with 3 or 4 bolts under the dash, assembly will come with paddle also, I belive the part number is 15027983 and cost about $60.00, dealer part only, hope this was very helpful.

Nov 11, 2010 | 2000 Chevrolet Silverado 1500

1 Answer

How can I adjust the clutch on my 2000 ply. neon


loosen the Adjustment screw on the Clutch master cylinder, carefully lift the pedal upward and connect the push rod to the pedal pin, Tighten the push rod adjustment screw, verify the the clutch operates correctly. (Haynes Repair Manual page 8-5, section 9 step 11 through 14) I highly recommend you get the Haynes repair manual on the vehicle ISBN: 978-1-56392-596-2 as it is possible that your vehicle may have a hydraulic clutch and if it does the steps to adjust the clutch assembly are more entailed.

Sep 28, 2010 | Plymouth Neon Cars & Trucks

2 Answers

Clutch assembly need diagram of assembly


autozone.com sign up its free then click on repair guides .... drive train....transaxle.....then manual trasaxle....then clutch it will give you the assembly and the torque ratio for your flywheel bolts

May 22, 2010 | 1997 Mitsubishi Eclipse

1 Answer

The fan is running in the same speed as the engine Sportage 2001


you need a repair manual.to get you started you going have to remove top radiator hose.you also have to remove clutch and fan as a assembly from water pump.you going have to remove fan shroud with clutch and fan as a assembly to make it easy to get out.once you remove fan and clutch.you have to remove clutch from fan.in order to put on a new one.

Jul 19, 2009 | 2000 Kia Sportage

1 Answer

Need to replace fan cluch


the radiator fan is mounted to the clutch, in other words remove the bolts / nuts that is holding the fan assembly to the water pump usually just four nuts once you pull the fan assembly the part that yo seperated from the water pump is the clutch, now remove the fan blades and mount thm on the new clutch assembly the piece which mounts tt the water ump is the fan clutch

Jul 10, 2009 | 2000 Kia Sportage

1 Answer

2000 ford taurus ac question: air conditoner works for a short time and starts to blow warm air. This is when the temperature reads hot on the temperature gauge. This occurred on a freeway with the outside...


your electric a/c clutch is wearing out. You have to remove compressor to replace the a/c clutch mounted on the compressor.

If you can get someone to shim it out a little bit, it would work ok. Call a few indpenedent shops and ask if they can shim it and how much it would cost.

Just say, I need to have the clutch on my a/c compressor shimmed so my a/c clutch clamps tighter. 2000 Taurus. How much to do that?

I would guess $100 max.

Otherwise, you need to have clutch & field coil assembly replaced. Around $300 - $350.

Here is a picture of the compressor with clutch mounted on front.

A/C Compressor and Clutch Assembly
FS-10 A/C Compressor
1fb4b5a.gif
A/C Compressor Clutch Assembly

149bdf0.gif

Apr 22, 2009 | 2000 Ford Taurus

1 Answer

2005 s10 fan clutch


autozone has a simple diagram but it serves your purpose
d404b2b.jpg

Aug 08, 2008 | 2004 Chevrolet S-10

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...