Question about Cars & Trucks

Open Question

2002 ford explorer power window cable came undone

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
allabouttile
  • 11 Answers

SOURCE: 2002 Ford Explorer passenger power window problem

Check the fuse panel first, after that check your fuse relays under the hood, if not then it might be a wiring problem.

Posted on Jul 30, 2009

Ad
  • 16 Answers

SOURCE: 2002 Ford Explorer, rear driver side door

Wil it work at the door switch or not at either switch? If not make sure you have power and ground to the motor in up and down positions. if so suspect the motor.Also the cable operated regulators break and will not let the window go up or down

Posted on Jul 30, 2009

harley9701ha
  • 424 Answers

SOURCE: How do I fix the problem of all 4 power windows

See if you have power coming out of the master power window switch when a button is pushed down. Remove a door panel and check for power at the window motor with the switch pushed. If you do not have power it could be the master switch. Good luck.

Posted on Aug 06, 2009

ZJLimited
  • 17970 Answers

SOURCE: 2002 explorer power window fuse where

In the battery Junction Box check fuse # 6-60AMP will feed Central Junction Box (under driver side), the inline circuit breaker #47-30AMP, through the Accessory Delay Relay, powered by fuse #17-15AMP to the Window Control Circuit. Check the fuses, and for 12v at the points. Then check for 12v at the driver side door switch pannel.

Also uou should check the plug into the main window button console in your drivers door. The little piece of plastic around the door handle pops out when pushed towards the front of the vehicle. This gives you access to the buttons and harnesses.

Good luck (remember rated this help).

Posted on Mar 09, 2010

Testimonial: "good but windows only opens when drivers door open"

ZJLimited
  • 17970 Answers

SOURCE: how do you replace the regulator for the power

Regulator - Power Windows - Front Door

  1. Remove the front door trim panel as follows:
    1. Remove the front door handle bezel.
    2. Remove the front door window/lock control switch bezel.
    3. Disconnect the window/lock control switch electrical connectors.
    4. Remove the 3 front door trim panel screws.
      CAUTION To avoid damaging the trim panel, do not pull directly outward to carry out this step.
    5. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    6. Remove the exterior mirror control switch from the front door trim panel.
  2. Remove the front door speaker.
  3. Remove the interior molding.
  4. Disconnect the door lock actuating rod at the door handle assembly:
    1. Release the door lock actuating rod clip.
    2. Position the door lock actuating rod aside.
  5. Remove the front door weather shield.
    CAUTION Make sure the holes in the glass bracket do not become enlarged during the rivet removal process. If the holes become enlarged, the new rivets may become loose, resulting in clicking noise concern.
    NOTE Some vehicles may use rivets to attach the window glass to the window regulator assembly. Use a 4.5 mm (0.1772 in) drill bit to drill out the glass-to-regulator rivets.
  6. Remove the 2 front door window glass-to-regulator bolts or rivets.
  7. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets.
  8. Secure the front door glass in the full up position with tape.
  9. Disconnect the window regulator motor electrical connector.
  10. Remove the 4 window regulator assembly nuts.
  11. Remove the window regulator assembly.

    0b00886.jpg

    Fig. Exploded view of the front door and power window components-2005 Explorer and Mountaineer

To install:
  1. Position the window regulator assembly.
  2. Install the 4 window regulator assembly nuts. Tighten to 89 inch lbs. (10 Nm).
  3. Connect the window regulator motor electrical connector.
  4. Remove the tape securing the front door glass in the full up position.
  5. Position the front door window glass as necessary to access the front door window glass-to-regulator bolts or rivets. Install the bolt and tighten the bolts to 62 inch lbs. (7 Nm), or install new rivets.
  6. Install the front door weather shield.
  7. Connect the door lock actuating rod at the door handle assembly:
    1. Position the door lock actuating rod into proper location.
    2. Attach the door lock actuating rod clip.
  8. Install the interior molding.
  9. Install the front door speaker.
  10. Install the front door trim panel as follows:
    1. Install the exterior mirror control switch from the front door trim panel.
    2. Position the door trim panel onto the armrest to engage the panel clips.
    3. Install the 3 front door trim panel screws.
    4. Connect the window/lock control switch electrical connectors.
    5. Install the front door window/lock control switch bezel.
    6. Install the front door handle bezel.

  1. Raise the front door window glass to the full up position.
  2. Remove the interior door handle.
  3. Support the front door window glass.
  4. Disconnect the front door window regulator motor electrical connector.
  5. Remove the equalizer bracket nuts.

    4945f24.jpg
    Fig. Remove the equalizer bracket nuts-2005 Explorer Sport-Trac
  6. Remove the front door window regulator by removing the rivets and nuts.
  7. Remove the front door window regulator motor retaining bolts and then remove the motor.

    52a6816.jpg

    Fig. Remove the front door window regulator motor retaining bolts and then remove the motor-2005 Explorer Sport-Trac
To install:
  1. Installation is the reverse of the removal procedure.
  2. Tighten the regulator motor mounting bolts to 8 ft. lbs. (11 Nm).

Hope this help (remember rated and comment this).

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I lost my manual guide for 2002 ford explorer. Witch fuse belongs to the power windows?


It is fuse #17 in the fuse block under the driver side dash. That fuse controls the dome light, radio, and power windows in the 2002 Explorer. Nowhere n the manual does it tell you that the power windows are on that fuse. I am going from recent personal experience. It is a 15A mini fuse (blade type). Good luck!

Oct 12, 2011 | 2002 Ford Explorer

1 Answer

Have a problem with rear passenger side power window. it went down fine, wouldnt come back up. checked all switches etc.


Take the door panel off. Common problem on ford trucks. You will see the window drive cable and the problem.

Mar 12, 2010 | 2002 Ford Explorer Sport Trac

2 Answers

How do i replace the power window door regulator?


auto zone can print for you the step by step instructions, they have alldata

Jan 21, 2010 | 2002 Ford Explorer

1 Answer

How do I get to the power window motor after I get the panels off my 2002 ford explorer? There appears to be a loose cable heading into the motor housing. Power widnow goes down but not up


You should see three star screws, Remove these and the motor should come off. Check the plastic plugs in the motor and replace with plugs or ball bearings, pack with wheel bearing grease. You may have a defective window regulator. To remove. using a /14 inch punch punch out the rivits and replace with 1/4 nuts and bolts. Drill out the aluminum inserts using 1/4 drill. When replacing the regulator do not over tighten the bolts holding in the glass.

Nov 27, 2009 | 2002 Ford Explorer

1 Answer

Window and radio quit working


Hi check your radio fuses

Sep 25, 2009 | 2002 Ford Explorer

1 Answer

Ford explorer 2002 front passenger window


You don't repair the cable. It is part of what is called the widow regulator. Call your parts store and check the prices. It will vary so call around. Some times you can order it without the motor, but often the cost with and without is not much different and it is better to get it as one unit.

Hope this helps.

Aug 28, 2009 | 2002 Ford Explorer

1 Answer

2002 Ford Explorer, rear driver side door


Wil it work at the door switch or not at either switch? If not make sure you have power and ground to the motor in up and down positions. if so suspect the motor.Also the cable operated regulators break and will not let the window go up or down

Jul 30, 2009 | 2002 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

58 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...