Question about 2005 Toyota 4 Runner

Open Question

How to install "anti rattle clips" on a 2006 toyota 4-runner

I need to know how to replace or install the anti rattle clips on a 2006 4-runner

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 184 Answers

SOURCE: How to reset the ''Check Engine'' light on a 1999 Toyota 4-Runner?

http://www.obd-codes.com/faq/reset_obd_codes.php

Posted on Apr 04, 2009

Ad
  • 161 Answers

SOURCE: Wiring for Toyota 4 Runner Alternator Fuse

it should be in the underhood fusebox on the right.

Posted on Jun 11, 2009

  • 73 Answers

SOURCE: HOW TO REPLACE STARTER 1996 TOYOTA 4 RUNNER

ARE YOU SURE THAT YOU NEED TO REMPLACE THE STARTER

Posted on Jul 26, 2009

  • 1 Answer

SOURCE: water leak under the intake manifold,1995 toyota 4 runner

There is a heater core bypass pipe that runs from the block (under the manifold) to the bacl of theengine where you will see a flat rectangular "sheet metal" thing with a pipe coming out of it. The a rubber hose connects. You need to pull the top air plenums and intake to get to it. The p[ipe flange bolts to the block with silicone rtv as a sealant.

Posted on Nov 27, 2009

Testimonial: "thanxs"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need the instructions on how to change a 2006 Toyota 4 runner alternator.


Disconnect battery, remove serpentine belt and any other components that are in the way. Remove bolts that hold alternator and re-install in opposite order.

Nov 12, 2016 | Toyota Cars & Trucks

1 Answer

99 Toyota 4 runner 2 wd front wheel removal


Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

Nov 26, 2015 | Toyota Cars & Trucks

2 Answers

Brakes rattle


To your direct question - I don't know the Highlander model in detail, but as a general response, if the brakes are noisy when NOT applied, the piston in your new caliper may not be returning properly.

The return spring in disc brakes is actually the rubber fitted around the caliper piston. If this is causing the piston to be wrongly positioned, the brakes will be noisy. Check that the rotor can be turned by hand when the brakes are not applied. Also check that the piston is not retracting from the pads a very long way, which it should not do.

It is worth making very sure the spring clips are fitted correctly. Some can be easily put in the wrong way round.

If the brakes are squealing when applied, that is a different problem. You can get a disc brake anti squeal liquid, which is applied to the back of the pad on assembly to the caliper. Also double check all the anti squeal shims are correctly installed.

At this range, that's all I can think of right now.

Nov 24, 2011 | 2005 Toyota Highlander

1 Answer

I need to know how to change the front brakes on a 94 jeep grand cherokee laredo.


  1. Raise and support the vehicle safely using jackstands. Remove the wheel(s) on the side to be worked on.

NOTE: Removing a small amount of brake fluid from the master cylinder using a turkey baster


zjlimited_10.jpg

Fig. 4: Tighten the C-clamp until the piston reaches the bottom of its bore


zjlimited_11.jpg

Fig. 5: Remove the caliper mounting bolts


zjlimited_12.jpg

Fig. 6: Slide the caliper off the brake rotor

  1. Drain a small amount of the brake fluid from the front reservoir using a suction gun or a turkey baster.
  2. Place a C-clamp on the caliper so that the solid end contacts the back of the caliper and the screw end contacts the metal part of the outboard brake pad.
  3. Tighten the clamp until the caliper moves far enough to force the piston to the bottom of the piston bore. This will back the brake pads off of the rotor surface to facilitate the removal and installation of the caliper assembly
zjlimited_13.jpg

Fig. 7: Support the caliper so that no tension is placed on the brake hose


zjlimited_14.jpg

Fig. 8: Hold the anti-rattle clip while removing the outboard pad (4)


zjlimited_15.jpg

Fig. 9: Removing the outboard brake pad


zjlimited_16.jpg

Fig. 10: Remove the inboard pad and anti-rattle clip


zjlimited_17.jpg

Fig. 11: Removing the inboard brake pad


zjlimited_18.jpg

Fig. 12: Removing the anti-rattle clip

  1. Remove the C-clamp.
Do not push down on the brake pedal or the piston and brake pads will return to their original positions up against the rotor.
  1. Remove the caliper mounting bolts. Tilt the top of the caliper outward and lift it off the rotor.
  2. Hold the anti-rattle clip against the caliper anchor plate and remove the outboard brake pad.
  3. Remove the inboard pad and the anti-rattle clip. Be sure that the support spring is removed with the inboard pad.
zjlimited_19.jpg

Fig. 13: Install the support spring onto the shoe of the inboard brake pad


zjlimited_20.jpg

Fig. 14: Installing the inboard pad


zjlimited_21.jpg

Fig. 15: Piston extension on new and worn brake pads

  1. Use a piece of wire to support the caliper so that no tension is placed on the brake hose. Do not allow the caliper to hang by the brake hose.
To install:
  1. Clean all the mounting holes and bushing grooves in the caliper ears. Clean the mounting bolts. Replace the bolts if they are corroded or if the threads are damaged. Wipe the inside of the caliper clean, including the exterior of the dust boot. Inspect the dust boot for cuts or cracks and for proper seating in the piston bore. If evidence of fluid leakage is noted, the caliper should be rebuilt.
Do not use abrasives on the bolts in order not to destroy their protective plating. You should not use compressed air to clean the inside of the caliper, as it may unseat the dust boot seal.
  1. If not already in place, attach the support spring to the inboard brake pad.
  2. Install the anti-rattle clip on the trailing end of the inboard pad's anchor plate. The split end of the clip must face away from the rotor.
  3. Install the inboard pad in the caliper. The pad must lay flat against the piston.
  4. Install the outboard pad in the caliper while holding the anti-rattle clip.
  5. With the pads installed, position the caliper over the rotor.
Before securing the caliper, ensure the brake hose is not twisted, kinked or touching any chassis parts.
  1. Lubricate the caliper pins and bushings with silicone grease. Line up the mounting holes in the caliper and the support bracket and insert the mounting bolts. Make sure that the bolts pass under the retaining ears on the inboard shoes. Push the bolts through until they engage the holes of the outboard pad and caliper ears. Thread the bolts into the support bracket and tighten them to 7-15 ft. lbs. (9-20 Nm).
CAUTION On models with manual/power brakes, pump the pedal until the caliper pistons and brake shoes are seated. On models with anti-lock brakes, turn the ignition ON and allow the booster pump to build pressure. Pump the brake pedal until the shoes are seated and the indicator lights turn off.
  1. Fill the master cylinder with brake fluid and pump the brake pedal to seat the pads.
  2. Install the wheel assembly and lower the vehicle. Check the level of the brake fluid in the master cylinder and fill as necessary.

Remember to rate this, good luck.

Nov 04, 2010 | 1994 Jeep Grand Cherokee

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Toyota 2006 4 Runner: What is the recommeneded milage schedule for replacement of the standard factory installed spark plugs?


Toyota recommends 5ys or 100k miles which ever comes first. As a professional mechanic, I recommend this at 3yrs or 80K miles for better performance and optimal gas mileage. Also having the spark plugs on the motor 5yrs/100k may lead to plug seizing to the aluminum heads.

May 22, 2010 | 2006 Toyota 4Runner

2 Answers

How easy it to change front brake pads on a toyota rav 4


not hard at all.remove tires.then remove 2 screws either 12mm or 14mm that hold the brake caliper in place.remove caliper but DO NOT disconnect the brake line from the caliper.get a C-CLAMP in order to get the caliper piston pushed back in.remove old brake pads and install new ones in the same order as the old ones were removed.you will want to check the rotors to make sure they are in good condition before you install the new pads,then put caliper back on and tighten screws to specs.do the same on the other side and always remember to PUMP YOUR BRAKE PEDAL A FEW TIMES IN ORDER FOR THE CALIPER PISTONS TO ENGAGE ON THE NEW PADS. hope this info helps.good luck and take care, manny

Mar 30, 2010 | 2006 Toyota RAV4

1 Answer

Remove a driver side door panel on a 2000 Toyota Limited 4 Runner


remove the screws that hold the inside door handle and clips behind the door panel

Jun 14, 2009 | 2000 Toyota Corolla

1 Answer

Replaced rear brakes, Alarms still active


i have a 2003 toyota 4-runner my brake and abs vsc are on and it has a beeping loud noise.....what do u think is the problem?

Aug 21, 2008 | 2003 Toyota 4Runner

Not finding what you are looking for?
2005 Toyota 4 Runner Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...