Question about 2001 Ford Escape

Open Question

Need this part YL8Z17271AA

Vehicle speed sensor for 2001 Ford Escape Manual Tranmission

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chiquititas
  • 1010 Answers

SOURCE: SPEED SENSOR

Start by checking these items-
* Open or short in vehicle speed sensor circuit
* Vehicle speed sensor
* Combination meter
* ECM

Posted on Jun 25, 2008

jgwhomeequip
  • 1902 Answers

SOURCE: O2 sensor

On the left front part of the engine, near the bottom, you also have a second one underneather the car right past the engine towards the rear of the car

Posted on Feb 08, 2009

landsend
  • 1066 Answers

SOURCE: ABS on 2001 Ford Escape .

could you have a low or odd sized tire on the car?  have you bumped a sensor?  Is the light on?

Posted on Apr 01, 2009

  • 6 Answers

SOURCE: 1999 FORD EXPEDITION VEHICLE SPEED SENSOR

It should be on the back of the transmission near where the driveshaft goes in. Buy a new one, jack up your truck and look for the old one on the back of the transmission

Posted on Apr 03, 2009

  • 24 Answers

SOURCE: Error code P0402 2001 Ford Escape

This might sound crazy but it works with these Escapes most of the time. Go buy a can of Seafoam from your part store. With the engine off, disconnect the brake booster vacuum line and place it in the can of sea foam. Start your engine and keep your foot on the gas pedal and keep the RPM's around 2k.The vehicle is going to smoke like crazy for 10 minutes or so, when the smoke clears up for the most part, go drive it for a couple of miles and see if that helps. It cleans out the carbon buildup from you intake and sensors and takes care of that code you getting most of the time. OR, you purge canister needs to be replaced...

Posted on Jul 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 ford escape 2.0 L 4 Cyl with 5 speed Manual Transmission. Recently had the clutch replaced with in a week the speedometer would be eratic but not all the time then after about a month on...


Definitely not an expert here, but exactly the same symptoms after a clutch replacement. I found one of the wires going to the connector on the harness side of the Vehicle Speed Sensor pulled in two. Can only surmise that during the clutch installation this connector wasn't disconnected and during movement of the transmission to get to the clutch was put under tension causing the failure. I haven't confirmed the solution yet, but pretty sure I'm on the right track.

Sep 12, 2012 | 2001 Ford Escape

1 Answer

I need to replace my iac valve/sensor on my 2001 ford escape v6. where will i find it hiding?


Why replacing? Codes/ Check Engine Light on?

adobe.gif Printable View (263 KB) TSB
06-11-7
  • 2001-2005 ESCAPE 3.0L UNSTABLE IDLE - 2001-2003 ESCAPE 3.0L AUTOMATIC TRANSAXLE SHUDDER - MEXICO ONLY
Publication Date: May 25, 2006
FORD: 2001-2005 Escape
ISSUE: Some 2001-2005 Escape vehicles equipped with a 3.0L engine may exhibit idle speeds outside the specified range. Some 2001-2003 Escape vehicles equipped with a 3.0L engine and CD4E automatic transaxle may exhibit a transmission shudder.
ACTION: Follow the Service Procedure steps to correct the condition.
SERVICE PROCEDURE
  1. If the concern is a 2001-2005 Escape with idle speeds outside the specified range:
    1. Install a new idle air control (IAC) valve with jumper harness included in the kit. The new Denso brand IAC will be installed with the electrical connector facing the opposite direction of the original (Hitachi) valve which is why the jumper harness is required. The original (Hitachi) IAC connector faces the front of the vehicle while the new Denso IAC connector faces toward the rear of the vehicle.
    2. Referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the powertrain control module (PCM) using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com.
  2. If the concern is a 2001 - 2003 Escape with transaxle shudder, drain, flush and refill the transmission fluid with MERCON® Multi-Purpose Automatic Transmission Fluid. Then, referring to the calibration charts (Figures 1 and 2), select the applicable file and reprogram the PCM using the TSB Service Procedure and WDS/IDS release B40.5 and higher. Calibration files may also be obtained at www.motorcraft.com.
  3. When reprogramming the PCM use blank path programming. Select the proper file from the chart and manually enter the PCM part number or tear tag number to obtain the updated calibration file.
To Perform Blank Path Programming:
  1. Connect WDS/IDS to vehicle.
  2. Select "16 pin", select "All others, except those below", press TICK.
  3. Screen shows installation of cable, press TICK.
  4. Screen shows to turn ignition ON. DO NOT TURN IGNITION ON. Press TICK.
  5. Screen shows progress bar, then screen tells you "No communication can be established with the PCM" and asks you if you want to retry? Select "NO". With the ignition key still OFF, press TICK.
  6. Screen shows to turn ignition ON. Keep ignition in the "OFF" position, press TICK and you will be asked to cycle the key "ON" and "OFF" a few times. Please keep the key position in the "OFF" position through the key cycles.
  7. Screen will show "The diagnostic tester is unable to communicate with this vehicle." You will be prompted to "select a vehicle from the vehicle list", press TICK.
  8. A list of vehicles will be displayed, select ALL OTHERS, and press TICK.
  9. Screen shows "To enable WDS to reprogram the PCM with the correct calibration", enter one of the following: Vehicle Calibration number (7 digits), Tear Tag number (4 digits), or PCM part number, press TICK.
  10. Highlight the box next to the selection chosen, and enter ONLY ONE of the selections listed above. Press TICK.
  11. Follow and answer correctly all remaining screens. Once PCM is reprogrammed communication should be reestablished and PATS system can be reset (if necessary) per Workshop Manual, Section 419-01.

PART NUMBER PART NAME 5L8Z-9F715-AA Idle Air Control Valve XT-2-QDX MERCON® Multi-Purpose Automatic Transmission Fluid
WARRANTY STATUS: Eligible Under Provisions Of New Vehicle Limited Warranty Coverage And Emissions Warranty Coverage
DEALER CODING BASIC PART NO. CONDITION CODE 9F715 42

tb8487b.gif
Figure 1 - Article 06-11-7



tb8488b.gif

Sep 07, 2011 | 2001 Ford Escape

1 Answer

How to find the tranmission abnd where the speed sincer is at?


Its in the rear of the transmission tail stock The vehicle also has a speed sensor on each front wheel make sure looking for the correct sensor

Dec 05, 2010 | 1997 Ford Taurus

1 Answer

Ford escape 2001. When I accelerate to overtake another car only the rpm shoot up but the speed does not increase.


your transmission needs immediate service. common with the escape. Turbine sensor or low transmission fluid in most cases. otherwise upwards to torque converter failure.
AAMCO transmissions should be your best start

Nov 07, 2009 | 2001 Ford Escape

2 Answers

Got code P1402 sum say it is EGR problem, but that code is P0402 I have check all componets and replaced senser,regarlator,and part right next to regalator. also the code was DPFE senser high voltage any...


code 1402 EGR valve position sensor open or shorted, check the wires going to the sensor and the plug itself,hope this helps if not get back to me and we'll go from there

May 15, 2009 | 2001 Ford Escape

1 Answer

2001 ford escape check engine light possible failed speed sensor


Yes. Replace the output speed sensor on the transmission.

May 13, 2009 | 2001 Ford Escape

1 Answer

Location


I think your vehicle uses a wheel speed sensor, vs a vehicle speed sensor on trans.

Mar 28, 2009 | 2003 Ford Escape

1 Answer

Transmission


valves that move to let fluid flow to determine what gear you are in. they should have warrantied it and you should not have payed for it!

Mar 01, 2009 | 2001 Ford Escape

1 Answer

Can not hold speed


check airflow sensor just borrow one and testand or try kickdown adj,or throttle possition sensor,check for air leaks by spraying airosole flammable near intake manifold,if it revs higher theres a leak

Jan 05, 2009 | 2002 Ford Escape

Not finding what you are looking for?
2001 Ford Escape Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...