Question about Chevrolet Impala

Open Question

Diagram of 2001 impala ls ignition switch replacement

I need to replace the ignition switch and can't figure out how to get to it

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Need to replace ignition cylinder on 2000 Impala

Pop off the black ring around ignition lock small screwdriver willl do. Remove dashboard plastic to expose 2 bolts holding ignition assy. Can be tedious. IF you can turn the key turn it to Start. In the plastic housing there's a 1/4 by 3/8 hole. push in a screwdriver which will push in a button on ignition cylinder and allow you to slide it out. The hole is located at 4 o'clock if we agree that the 2 wiring harness plugs are at 6 o clock and its 1 and 1/4 inches below the face of ignition cylinder. If you dont feel that the screwdriver is pushing in that "button" rotate your key until it does. Then just slide the cylinder out.

Posted on Apr 12, 2009

Ad
  • 6982 Answers

SOURCE: 2001 Chevy impala had ignition switch replaced,

Turn the key to "on" and let the light flash. It should stop flashing after about ten to twenty minutes. Once the light is on steady, turn it off, then start the car. I usually put another battery on jumper cables attached to the cars battery so it does not run down and die before the system re-arms.

Posted on Aug 16, 2009

  • 8 Answers

SOURCE: NEED ENGINE DIAGRAM FOR REPLACING

sorry no diagram but rather simple on either side of the engine there are plastic covers in the middle of the valve cover take that off to expose the coil packs disconnect them and the spark plugs are right there in the well i beleave a 5/8 deep well socket and a couple extentions and u should be good

Posted on Sep 03, 2009

  • 14036 Answers

SOURCE: ignition switch 2001 chevrolet impala

YOU NEED A HAYNES REPAIR MANUAL WITH PHOTOS TO SHOW YOU HOW TO REMOVE STEERING WHEEL AND DISABLE AIRBAGS.YOUR IGNITION SWITCH IS IN THE STEERING COLUMN.

Posted on Jul 07, 2010

  • 3074 Answers

SOURCE: My key will not turn my ignition switch. Yesterday

you can look at this website, it may help Tim:

http://wiki.answers.com/Q/How_do_you_unlock_a_steering_wheel_It_is_locked_and_the_key_will_not_work

Posted on Oct 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 Chevy Impala LS that won't crank,


I doubt it has anything to do with the key switch.
If the security system is the cause, the security warning light should be on.
Someone would need to check the circuit between the key switch and the starter when it fails to crank to find the problem.

Apr 30, 2013 | Cars & Trucks

2 Answers

My 2001 lincon ls shuts off when driving then struggles to turn on


1) Reset the ignition timing according with the instruction manufacturer.
2) Test the primary and secondary circuite from ignition system
See the diagrams attached. God bless you
5_15_2012_6_34_00_am.jpg5_15_2012_6_34_34_am.jpg5_15_2012_6_35_18_am.jpg5_15_2012_6_35_36_am.jpg

May 15, 2012 | 2001 Lincoln LS V8

1 Answer

2001 impala replaced ignition switch, now wont turn over. NO security in message center


Unless you used the correct coded key cylinder the engine will not start.

Mar 28, 2017 | Chevrolet Impala Cars & Trucks

1 Answer

Ignition switch 2001 chevrolet impala


YOU NEED A HAYNES REPAIR MANUAL WITH PHOTOS TO SHOW YOU HOW TO REMOVE STEERING WHEEL AND DISABLE AIRBAGS.YOUR IGNITION SWITCH IS IN THE STEERING COLUMN.

Jul 07, 2010 | 2001 Chevrolet Impala

3 Answers

Ignition control module on a 2001 Chevy Impala


There is a switch relay that plugs behine the ignition switch cylinder.You would have to take apart the dash console to take it apart to replace it.Also helps solve a few problem on the 2001 chevrolet impala, with heat gauage not working and a/c not blowing cold air anymore.Replacing it, should fix the problem with that.

Apr 11, 2010 | 2001 Chevrolet Impala

2 Answers

Tempature Gauge is not working on my 2001 Chevrolet Impala LS.


Sounds like a bad coolant temp sensor. Do you have a check engine light on?

Mar 24, 2009 | 2005 Chevrolet Impala

1 Answer

Serpentine belt replacement on 2001 impala


I bought a new belt and it had a series of diagrams for different engines on the cardboard packaging (ie GM 3.8L). I needed it for my '01 Impala.

Sep 01, 2008 | 2001 Chevrolet Impala

2 Answers

01-LS stops when idling/driving/hot/cold....


make sure to check for and aftermarket ignition module installation in other words make sure the ignition module is factory and not aftermarket,
this is not a fuel problem because fuel problem acts diferent
but coul be your ignition module or your crank sensor

May 28, 2008 | 2001 Chevrolet Impala

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

126 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...