Question about 2003 Chrysler Concorde

1 Answer

2000 CHRYSLER CONCORDE HEADLIGHT BULB REPLACEMENT

HOW DO YOU EXTRACT THE HEADLIGHT HOUSING, IN ORDER TO CHANGE THE BULB? I REMOVED THE TWO LONG SCREWS. BUT CANNOT PULL THE HOUSING FORWARD. DO YOU HAVE TO REMOVE THE WHOLE FRONT BUMPER?

Posted by on

  • boxerbeya Jan 26, 2009

    this is impossible as there is no space large enough behind the housing to extract the bulb. this is the driver side headlight on a chrysler concorde 2000. this is the first time that i have requested info from your site.

  • Anonymous Mar 24, 2014

    I accidently ripped the right front bumper forward from a wood box. I didn't see it underneath all the snow. How do I fix it?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 5,158 Answers

Thought i already answered this... must have been for someone else... you should be able to access the bulb from within the engine compartment... if it's on the side of the battery you may have to remove it. do not touch the bulb with your fingers as that shortens the life of it.

Robert

Posted on Jan 26, 2009

  • Roberta Smith
    Roberta Smith Jan 26, 2009

    REMOVAL
    Release hood latch and open hood.
    Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
    Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
    Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
    Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
    Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
    Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    Remove headlamp housing Remove Headlamp Housing
    INSTALLATION
    CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

    Place headlamp housing into position.
    Connect wire connector to lamp socket(s) and/or bulbs.
    Verify headlamp and signal lamp operation.
    Install jackscrews to attach headlamp housing to crossmember.
    Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    Install nut on fascia stud through the splash shield access hole.
    Verify headlamp operation and alignment




    that should help.... perhaps if that does assist you better .. please change the rating on this solution... thanks

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a headlight bulb on a 1996 Chrysler Concorde. Driver side and passenger side.


Assuming you can't find access to the headlights, like a lot of newer cars, then try this:
If you don't have access to the lights under the hood. Look around the headlights outside. There must be a screw on or under the headlight mount. maybe under the bumper.

But if you have access to the bulbs now, then use gloves to replace the bulbs if they are the newer hot bulbs. A finger print on those bulbs can cause it to explode.
Some bulbs twist and turn out, others just pull out straight.
Hope this helps.

Mar 29, 2015 | 1996 Chrysler Concorde

1 Answer

How to remove headlights on 98 chrysler concorde


Lift hood and you should see 2 or 3 screws holding complete housing. Remove them and pull complete housing out to make it easy to replace bulbs.

Oct 30, 2011 | 1998 Chrysler Concorde

2 Answers

How do i get to my low beams on my chrysler 2005 sebring sedan i got to the high beams perfect but the low beams right next to it has a metal barrier surrounding it which makes it impossible


Unfortunately, the answer I have is not a happy one =(. My wife has a 2005. In order to replace the bulb you will have to pull the Crutons (plastic push pins) that hold the front bumber cover on, remove the Headlight housing & replace the bulb that way. Shame on Chrysler for making it so difficult, in my opinion. But I hope this helps you to change the bulb =)

Aug 26, 2011 | 2004 Chrysler Sebring

1 Answer

How do you change the brake light on the back window on a 2000 chrysler concorde


  1. Release decklid latch and open decklid.
  2. From under rear shelf panel, disconnect the lamp socket from the CHMSL housing.
  3. Remove bulb from the socket.
INSTALLATION
  1. Install the bulb into the socket.
  2. Install socket into CHMSL housing.
  3. Verify CHMSL operation.

Apr 19, 2011 | 2000 Chrysler Concorde

1 Answer

How to replace bulbs in headlights in a 1995 Chrysler Concorde


In my 2000 you have to pull the headlight assembly out.

Oct 18, 2009 | 1995 Chrysler Concorde

2 Answers

Replace low beam on 2000 LHS


The headlight housing must be removed to access the bulbs on the back of the housing. HOWEVER!!! you must take loose the bumper on the side you are replacing. To do this you also have to take loose the inner finder and turn you wheel sharply in the opposite direction of the bulb to be replaced. There is a 10mm nut you will have to remove inside as well as multiple plastic fasteners along the inner finder and across the front under the hood. Bulb just twist out to remove once the housing is removed. Also, resist the urge to use a very large hammer. Use caution when pulling the plastic bumper out where the 10mm nut was removed, the stud can easily scratch the paint while working the housing out of its socket.

Jun 25, 2009 | 2000 Chrysler LHS

1 Answer

How to change headlight in 2000 chrysler sebring convertible


There is a cover over the bulb that is removed by turning counter clockwise. (as viewed from the back of the housing)
Remove the spring clip that holds the bulb and pull out bulb.
Plug in new bulb (do not touch glass with hands) and install re-install spring clip and back cover.

Mar 15, 2009 | 2000 Chrysler Sebring

1 Answer

DHOW TO CHANGE OUT HEADLIGHT BULB ON 1996 CHRYSLER CONCORD LXI


For the bulb removal follow these steps.
-Open the hood and look behind the headlamp assembly with the burned out bulb.
-You'll see a black plastic ring about 2 inches in diameter, rotate this a quarter turn.
-Unplug the bulb, gently pulling the clip up to release the bulb.

Feb 05, 2009 | 1996 Chrysler Concorde

2 Answers

How do you replace the headlight bulb on a 2001 chrysler lhs.


This can be done buy popping the hood and removing the bulb from the rear of the headlight housing. don't screw with the housing because, its leveled for optimal sight range.

Jan 28, 2009 | 2000 Chrysler LHS

1 Answer

How do I remove the headlight assembly


two torx head screws per headlight, once you loosen them you will see they are very long, pull them out and the headlight should pull forward

Nov 17, 2008 | 2003 Chrysler Concorde

Not finding what you are looking for?
2003 Chrysler Concorde Logo

2,675 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...