Question about 1991 Dodge Dynasty

1 Answer

Dodge dynasty driving heard pop voltage drop to 0 no click no

Start everything else works

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 141 Answers

Sounds to me like the inline fuse popped on you. It should be located on the fat red wire going to your starter. Hope this helps. Best wishes and God Bless.
Bryon

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1990 dodge dynasty with shifting problems i have had the seloind pack replaced still stifts rough and still will drop out of drive down into second and then dosen't want to shift back to driv


go to the scrapyard and find a accident damaged vehicle then buy the box and the computer and change the whole lot ,failing which buy a newer secondhand car as it may be cheaper in the long run preffably one with a manual gearbox

Dec 11, 2011 | 1990 Dodge Dynasty

1 Answer

1993 Dodge Dynasty


the blower motors armature could of gone bad, if any noises were heard before hand it was caused by a worn bearing. it will lock solid if this was the case

Feb 20, 2010 | 1993 Dodge Dynasty

1 Answer

We are having trouble with the engine light staying on and the voltage going down to 0 , when we are driving it .My husband put on a new battery end tonight and still won't stay off. It has a new battery...


Since the voltage shows 0, that indicates the battery is not charging. You most likely need a new alternator. Drive the car (while you still can) to a parts store, they will check the charging system for free, and advise you on what to do to fix the problem.

Dec 05, 2009 | 1993 Dodge Dynasty

2 Answers

Dodge dynasty wont star battery is good lites work


check for proper ground to body and engine, check for proper gauge of cables used.

Jul 18, 2009 | 1993 Dodge Dynasty

1 Answer

Fuel pressure drops immediately to zero when engine is shut off.


I am not really familiar with the setup there but I'd be looking for a second relay to kick the pump on when cranking.

Jun 05, 2009 | 1991 Dodge Dynasty

1 Answer

Reset factory alarm on 90 dodge dynasty key in door does not work


i have 1989 dynasty and my factory alarm is still engaged and i am unable to start my care how can i fix it

Mar 24, 2009 | 1990 Dodge Dynasty

1 Answer

Heater on 1993 dodge dynasty


Make sure the hoses aren't plugged up before you start tearing things apart. Also check any fuses or relays. The relays are in the engine compartment on the left side just above the battery. If you pop open that lid on the plain unmarked black box, it will tell you what each relay is for. Hope this helps.

Oct 22, 2008 | 1993 Dodge Dynasty

1 Answer

Charging problem


Could you clarify your engine size?

4 Cylinders K 2.5L TBI SOHC 6 Cylinders 3 3.0L FI (found in 36% of 1990 Dodge Dynasty) 6 Cylinders R 3.3L FI (found in 64% of 1990 Dodge Dynasty)


If you have the 3.3L the voltage regulators are located in the Powertrain Control Module (PCM) or Single Board Engine Controller (SBEC), depending on the model. If, after diagnosis, the regulator is deemed faulty, the PCM/SBEC must be replaced with a new one.

Hope this helps for now

Jul 06, 2008 | 1990 Dodge Dynasty

Not finding what you are looking for?
1991 Dodge Dynasty Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...