Question about 1989 Mazda 626

1 Answer

Turn signals not working

Earlier today my right front and back turn signals would not work. i removed the fuse and replaced it, (it was not blown btw) . when i replaced it neither turn signal will work now. and i put the exact same fuse back in and tried a new one. my hazard lights work but only on the left side. i am sure i have two problems.

Posted by on

  • Denise Jones Sep 03, 2013

    I have similar problem with my 2001 millenia... hazards and turn signals not working; right side stayed on; removed hazard fuse to turn off light so it wouldn't continue to drain battery; where can i get this flasher relay from

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

There should be A Fuse Relay Box under the Hood. There is a Flasher Relay in it for the Blinkers. Replace this Relay and it should be good. Please Rate my response,I need all the Help I can get! Thanks!

Posted on Jan 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal fuze


There is not fuse just for the right front. If the fuse is blown none of the turn signals will work

Aug 02, 2016 | Cars & Trucks

1 Answer

99 windstar driver side turn signal not working left rear flashes fast


computer glitch do not know if you got last answer so here we go again

You have a right front or rear turn signal/parking light bulb blown.

turn on flashers it might help locate which one .
Remove the lens cover push and twist to remove blown bulb
replace with 1157 2 element bulb
install reverse order
Hope this helps Mike

Jan 18, 2016 | Cars & Trucks

2 Answers

Front right and back right turn signal wont work but the front left and back left do


first check the bulbs on that side by visual or changing to the other side if you can't see that well if the bulbs from the front and back work or are good when checked the flasher has blown out on one side and you have to replace it other possible cause could be a broken wire for the right side lights so look at the connectors for that side front & back if all is good one more thing could do this the actual turn signal lever that you use to activate the signals could be bad for the right side especially if it does not go back to the normal position after making a turn and the steering wheel rotates back to it's normal position but the turn signal lever does not click back to the center position this would burn out that side from the signal constantly being on good luck stephen

Jan 03, 2015 | 1991 Ford Probe

1 Answer

Cadillac srx 2007


sounds like a fuse is blown. check your fuses

Aug 02, 2013 | Cars & Trucks

1 Answer

Turn signals not working properly


replace flasher, under your dash, its a round, metal cap shaped unit , try that, also, change your rear bulbs, sometimes the ones that work are the problem, check your fuses also !

Mar 25, 2013 | 1998 Dodge Durango

3 Answers

My rear brake light is not working, nor is my blinker at the back right. When I put the right turn signal on it blinks really fast, faster than normal, and the front blinker works. I have replaced both...


Normally with the blinker blinking really fast, it's telling you that one of the bulb is blown, front or rear signals. Check your fuse, and fuse relay to see if it would fix the promblem

Jan 23, 2011 | Chevrolet K3500 Cars & Trucks

1 Answer

How to change the turn signal flasher?


Check the the bulbs at the front and rear of the vehicle work. If one is not lit up, replace that one. On some of the earlier model cars the blinkers would stay solid and not flash when one or both bulbs were blown. Modern cars have a rapid flash when one or both are blown

Nov 24, 2009 | Oldsmobile Cutlass Supreme Cars & Trucks

2 Answers

2002 Hyundai elantra driver side turn signal not working outside


This simply means that the front driver side turn signal bulb has failed. Replace it.

Oct 28, 2009 | 2000 Nissan Maxima

1 Answer

The turn signals do not work on 2000 nissan exterra.Fuse was blown. Replaced and blew again after a few seconds.


1.Remove front & Rear turn signal Bulbs.
2.Replace Fuse.
3.Signal on.
4.Fix rear Signal Bulb.
5.Fix Front Signal Bulb.
7.If your Fuse blown.
8.Defect is There.

Jun 11, 2009 | 2000 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

357 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...